Some boards are using one mdio bus which holds multiple phys and also
boards are using mdio node for bus description. That's why there are cases
where address/size-cells are unnecessary which is also reported by make W=1
dtbs. That's why remove them from zynqmp.dtsi and let board DTSes to handle
it based on used description.
Error log:
/axi/ethernet@ff0e0000: unnecessary #address-cells/#size-cells without
"ranges" or child "reg" property
Signed-off-by: Michal Simek <michal.simek@xxxxxxx>
---
arch/arm64/boot/dts/xilinx/zynqmp.dtsi | 8 --------
1 file changed, 8 deletions(-)
diff --git a/arch/arm64/boot/dts/xilinx/zynqmp.dtsi b/arch/arm64/boot/dts/xilinx/zynqmp.dtsi
index e50e95cbe817..f5e1eb8cb3b7 100644
--- a/arch/arm64/boot/dts/xilinx/zynqmp.dtsi
+++ b/arch/arm64/boot/dts/xilinx/zynqmp.dtsi
@@ -584,8 +584,6 @@ gem0: ethernet@ff0b0000 {
<GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>;
reg = <0x0 0xff0b0000 0x0 0x1000>;
clock-names = "pclk", "hclk", "tx_clk", "rx_clk", "tsu_clk";
- #address-cells = <1>;
- #size-cells = <0>;
iommus = <&smmu 0x874>;
power-domains = <&zynqmp_firmware PD_ETH_0>;
resets = <&zynqmp_reset ZYNQMP_RESET_GEM0>;
@@ -600,8 +598,6 @@ gem1: ethernet@ff0c0000 {
<GIC_SPI 59 IRQ_TYPE_LEVEL_HIGH>;
reg = <0x0 0xff0c0000 0x0 0x1000>;
clock-names = "pclk", "hclk", "tx_clk", "rx_clk", "tsu_clk";
- #address-cells = <1>;
- #size-cells = <0>;
iommus = <&smmu 0x875>;
power-domains = <&zynqmp_firmware PD_ETH_1>;
resets = <&zynqmp_reset ZYNQMP_RESET_GEM1>;
@@ -616,8 +612,6 @@ gem2: ethernet@ff0d0000 {
<GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>;
reg = <0x0 0xff0d0000 0x0 0x1000>;
clock-names = "pclk", "hclk", "tx_clk", "rx_clk", "tsu_clk";
- #address-cells = <1>;
- #size-cells = <0>;
iommus = <&smmu 0x876>;
power-domains = <&zynqmp_firmware PD_ETH_2>;
resets = <&zynqmp_reset ZYNQMP_RESET_GEM2>;
@@ -632,8 +626,6 @@ gem3: ethernet@ff0e0000 {
<GIC_SPI 63 IRQ_TYPE_LEVEL_HIGH>;
reg = <0x0 0xff0e0000 0x0 0x1000>;
clock-names = "pclk", "hclk", "tx_clk", "rx_clk", "tsu_clk";
- #address-cells = <1>;
- #size-cells = <0>;
iommus = <&smmu 0x877>;
power-domains = <&zynqmp_firmware PD_ETH_3>;
resets = <&zynqmp_reset ZYNQMP_RESET_GEM3>;
--
2.36.1
