Re: [PATCH 6/7] ARM: at91: dts: sama5d3: add ov2640 camera sensor support

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 





Hi, Laurent

On 12/18/2014 8:32 PM, Laurent Pinchart wrote:
Hi Josh,

Thank you for the patch.

On Thursday 18 December 2014 16:51:06 Josh Wu wrote:
According to v4l2 dt document, we add:
   a camera host: ISI port.
   a i2c camera sensor: ov2640 port.
to sama5d3xmb.dtsi.

In the ov2640 node, it defines the pinctrls, clocks and isi port.
In the ISI node, it also reference to a ov2640 port.

Signed-off-by: Josh Wu <josh.wu@xxxxxxxxx>
---
  arch/arm/boot/dts/sama5d3xmb.dtsi | 32 ++++++++++++++++++++++++++++++++
  1 file changed, 32 insertions(+)

diff --git a/arch/arm/boot/dts/sama5d3xmb.dtsi
b/arch/arm/boot/dts/sama5d3xmb.dtsi index 0aaebc6..958a528 100644
--- a/arch/arm/boot/dts/sama5d3xmb.dtsi
+++ b/arch/arm/boot/dts/sama5d3xmb.dtsi
@@ -52,6 +52,29 @@
  				};
  			};

+			i2c1: i2c@f0018000 {
+				ov2640: camera@0x30 {
+					compatible = "ovti,ov2640";
+					reg = <0x30>;
+					pinctrl-names = "default";
+					pinctrl-0 = <&pinctrl_isi_pck_as_mck
&pinctrl_sensor_power &pinctrl_sensor_reset>;
+					resetb-gpios = <&pioE 24 GPIO_ACTIVE_LOW>;
+					pwdn-gpios = <&pioE 29 GPIO_ACTIVE_HIGH>;
+					/* use pck1 for the master clock of ov2640 */
+					clocks = <&pck1>;
+					clock-names = "xvclk";
+					assigned-clocks = <&pck1>;
+					assigned-clock-rates = <25000000>;
+
+					port {
+						ov2640_0: endpoint {
+							remote-endpoint = <&isi_0>;
+							bus-width = <8>;
+						};
+					};
+				};
+			};
+
  			usart1: serial@f0020000 {
  				dmas = <0>, <0>;	/*  Do not use DMA for usart1 */
  				pinctrl-names = "default";
@@ -60,6 +83,15 @@
  			};

  			isi: isi@f0034000 {
+				port {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
I would add the port node and those two properties to
arch/arm/boot/dts/sama5d3.dtsi, as the isi has a single port. The endpoint, of
course, should stay in this file.

That makes sense. I'll fix that. Thanks for the review.

Best Regards,
Josh Wu

+					isi_0: endpoint {
+						remote-endpoint = <&ov2640_0>;
+						bus-width = <8>;
+					};
+				};
  			};

  			mmc1: mmc@f8000000 {

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html




[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]
  Powered by Linux