Re: [PATCH 6/7] ARM: at91: dts: sama5d3: add ov2640 camera sensor support

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 




Hi Josh,

Thank you for the patch.

On Thursday 18 December 2014 16:51:06 Josh Wu wrote:
> According to v4l2 dt document, we add:
>   a camera host: ISI port.
>   a i2c camera sensor: ov2640 port.
> to sama5d3xmb.dtsi.
> 
> In the ov2640 node, it defines the pinctrls, clocks and isi port.
> In the ISI node, it also reference to a ov2640 port.
> 
> Signed-off-by: Josh Wu <josh.wu@xxxxxxxxx>
> ---
>  arch/arm/boot/dts/sama5d3xmb.dtsi | 32 ++++++++++++++++++++++++++++++++
>  1 file changed, 32 insertions(+)
> 
> diff --git a/arch/arm/boot/dts/sama5d3xmb.dtsi
> b/arch/arm/boot/dts/sama5d3xmb.dtsi index 0aaebc6..958a528 100644
> --- a/arch/arm/boot/dts/sama5d3xmb.dtsi
> +++ b/arch/arm/boot/dts/sama5d3xmb.dtsi
> @@ -52,6 +52,29 @@
>  				};
>  			};
> 
> +			i2c1: i2c@f0018000 {
> +				ov2640: camera@0x30 {
> +					compatible = "ovti,ov2640";
> +					reg = <0x30>;
> +					pinctrl-names = "default";
> +					pinctrl-0 = <&pinctrl_isi_pck_as_mck
> &pinctrl_sensor_power &pinctrl_sensor_reset>;
> +					resetb-gpios = <&pioE 24 GPIO_ACTIVE_LOW>;
> +					pwdn-gpios = <&pioE 29 GPIO_ACTIVE_HIGH>;
> +					/* use pck1 for the master clock of ov2640 */
> +					clocks = <&pck1>;
> +					clock-names = "xvclk";
> +					assigned-clocks = <&pck1>;
> +					assigned-clock-rates = <25000000>;
> +
> +					port {
> +						ov2640_0: endpoint {
> +							remote-endpoint = <&isi_0>;
> +							bus-width = <8>;
> +						};
> +					};
> +				};
> +			};
> +
>  			usart1: serial@f0020000 {
>  				dmas = <0>, <0>;	/*  Do not use DMA for usart1 */
>  				pinctrl-names = "default";
> @@ -60,6 +83,15 @@
>  			};
> 
>  			isi: isi@f0034000 {
> +				port {
> +					#address-cells = <1>;
> +					#size-cells = <0>;
> +

I would add the port node and those two properties to 
arch/arm/boot/dts/sama5d3.dtsi, as the isi has a single port. The endpoint, of 
course, should stay in this file.

> +					isi_0: endpoint {
> +						remote-endpoint = <&ov2640_0>;
> +						bus-width = <8>;
> +					};
> +				};
>  			};
> 
>  			mmc1: mmc@f8000000 {

-- 
Regards,

Laurent Pinchart

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html




[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]
  Powered by Linux