On 05/08/2023 19:03, Xilin Wu via B4 Relay wrote:
> From: Xilin Wu <wuxilin123@xxxxxxxxx>
>
> Add support for Xiaomi Mi 11 Ultra. This commit brings support for:
> * Front and rear display panels (initialized by bootloader)
> * USB
> * UFS
> * PCIe0
> * Thermistor sensors
> * ADSP/CDSP/Modem/SLPI
> * IR Transmitter
> * RTC provided by PMK8350
> * Buttons
>
...
> +/*
> + * Delete following upstream (sm8350.dtsi) reserved
> + * memory mappings which are different on this device.
> + */
> +/delete-node/ &pil_adsp_mem;
> +/delete-node/ &pil_slpi_mem;
> +/delete-node/ &pil_cdsp_mem;
> +/delete-node/ &pil_ipa_fw_mem;
> +/delete-node/ &pil_ipa_gsi_mem;
> +/delete-node/ &pil_gpu_mem;
> +/delete-node/ &pil_spss_mem;
> +/delete-node/ &pil_modem_mem;
> +/delete-node/ &rmtfs_mem;
> +/delete-node/ &pil_trustedvm_mem;
> +/delete-node/ &removed_mem;
> +
> +/ {
> + model = "Xiaomi Mi 11 Ultra";
> + compatible = "xiaomi,star", "qcom,sm8350";
> + chassis-type = "handset";
> +
> + chosen {
> + #address-cells = <2>;
> + #size-cells = <2>;
> + ranges;
> +
> + framebuffer0: framebuffer-front@ea600000 {
framebuffer@
> + compatible = "simple-framebuffer";
> + reg = <0 0xea600000 0 (1440 * 3200 * 4)>;
> +
> + width = <1440>;
> + height = <3200>;
> + stride = <(1440 * 4)>;
> + format = "a8r8g8b8";
> + };
> +
> + framebuffer1: framebuffer-rear@eb79c000 {
framebuffer@
> + compatible = "simple-framebuffer";
> + reg = <0 0xeb79c000 0 (126 * 294 * 4)>;
> +
> + width = <126>;
> + height = <294>;
> + stride = <(126 * 4)>;
> + format = "a8r8g8b8";
> + };
> + };
> +
> + reg = <0 0x86100000 0 0x3900000>;
> + no-map;
> + };
> +
> + pil_slpi_mem: memory@89a00000 {
> + reg = <0 0x89a00000 0 0x2f00000>;
> + no-map;
> + };
> +
> + pil_cdsp_mem: memory@8c900000 {
> + reg = <0 0x8c900000 0 0x1e00000>;
> + no-map;
> + };
> +
> + pil_ipa_fw_mem: memory@8e700000 {
> + reg = <0 0x8e700000 0 0x10000>;
> + no-map;
> + };
> +
> + pil_ipa_gsi_mem: memory@8e710000 {
> + reg = <0 0x8e710000 0 0xa000>;
> + no-map;
> + };
> +
...
> +&pm8350c_gpios {
> + gpio-line-names = "VDD_BOOST_5V_EN",
> + "NC",
> + "OTG_OVP_EN",
> + "WL_TXON",
> + "NC",
> + "NC",
> + "NC",
> + "NC",
> + "NC";
> +};
> +
> +&pmk8350_adc_tm {
> + status = "okay";
> +
> + pm8350-skin-therm@0 {
Hm, didn't we change the node names to generic "channel" and started
using labels? At least in next or ongoing patches? Or was it only for VADC?
> + reg = <0>;
> + io-channels = <&pmk8350_vadc PM8350_ADC7_AMUX_THM1_100K_PU(1)>;
> + qcom,ratiometric;
> + qcom,hw-settle-time-us = <200>;
> + };
...
> +
> +&ufs_mem_hc {
> + status = "okay";
> +
> + reset-gpios = <&tlmm 203 GPIO_ACTIVE_LOW>;
> +
> + vcc-supply = <&vreg_l7b_2p96>;
> + vcc-max-microamp = <800000>;
> + vccq-supply = <&vreg_l9b_1p2>;
> + vccq-max-microamp = <900000>;
> +};
> +
> +&ufs_mem_phy {
> + status = "okay";
> +
> + vdda-phy-supply = <&vreg_l5b_0p88>;
> + vdda-pll-supply = <&vreg_l6b_1p2>;
> +};
> +
> +&usb_1 {
> + /* USB 2.0 only */
> + qcom,select-utmi-as-pipe-clk;
> + status = "okay";
> +};
> +
> +&usb_1_dwc3 {
> + dr_mode = "otg";
> + usb-role-switch;
> + maximum-speed = "high-speed";
> + /* Remove USB3 phy */
> + phys = <&usb_1_hsphy>;
> + phy-names = "usb2-phy";
> +};
> +
> +&usb_1_dwc3_hs {
> + remote-endpoint = <&pmic_glink_hs_in>;
> +};
> +
> +&usb_1_hsphy {
> + status = "okay";
> +
> + vdda-pll-supply = <&vreg_l5b_0p88>;
> + vdda18-supply = <&vreg_l1c_1p8>;
> + vdda33-supply = <&vreg_l2b_3p07>;
> +};
> +
Looks like you have trailing blank line.
Best regards,
Krzysztof
