Re: [PATCH v3 2/4] ARM: dts: imx6qdl: Add Variscite VAR-SOM-MX6 SoM support

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Thu, Jul 20, 2023 at 7:27 AM Fabio Estevam <festevam@xxxxxxxxx> wrote:
>
> On Thu, Jul 20, 2023 at 10:10 AM James Hilliard
> <james.hilliard1@xxxxxxxxx> wrote:
>
> > +       reg_audio: regulator-audio {
> > +               compatible = "regulator-fixed";
> > +               regulator-name = "tlv320aic3x-supply";
> > +               enable-active-high;
>
> enable-active-high should only be used when there is a corresponding
> gpio property.
>
> > +&ecspi3 {
> > +       fsl,spi-num-chipselects = <1>;
> > +       pinctrl-names = "default";
> > +       pinctrl-0 = <&pinctrl_ecspi3>;
> > +       cs-gpios = <&gpio4 24 GPIO_ACTIVE_HIGH>;
>
> This should be ACTIVE_LOW instead.
>
> > +       status = "okay";
> > +};
> > +
> > +&fec {
> > +       pinctrl-names = "default";
> > +       pinctrl-0 = <&pinctrl_enet>;
> > +       phy-mode = "rgmii";
> > +       phy-reset-gpios = <&gpio1 25 GPIO_ACTIVE_LOW>;
>
> This is a deprecated property.
>
> The recommendation is to add a mdio node with:
>
> reset-gpios = <&gpio1 25 GPIO_ACTIVE_LOW>;
> reset-assert-us = <10000>;
>
> Is this an Atheros AR8031 PHY. If so, please check imx6qdl-sabresd.dtsi.

Hmm, the datasheet appears to indicate it uses a KSZ9031RN ethernet phy.

Would that be a different configuration vs the Atheros AR8031 PHY?

>
> > +&ssi2 {
> > +       fsl,mode = "i2s-slave";
>
> This is unused, drop it.
>
> Please check commit ece1e4999 606 ("ASoC: fsl_ssi: Remove unneeded
> 'i2s-slave' property")
>
> > +&usdhc3 {
> > +       pinctrl-names = "default", "state_100mhz", "state_200mhz";
> > +       pinctrl-0 = <&pinctrl_usdhc3>;
> > +       pinctrl-1 = <&pinctrl_usdhc3_100mhz>;
> > +       pinctrl-2 = <&pinctrl_usdhc3_200mhz>;
> > +       bus-width = <4>;
> > +       vmmc-supply = <&reg_wl18xx_vmmc>;
> > +       non-removable;
> > +       wakeup-source;
> > +       keep-power-in-suspend;
> > +       cap-power-off-card;
> > +       #address-cells = <1>;
> > +       #size-cells = <0>;
> > +       status = "okay";
> > +
> > +       wifi: wifi@0 {
> > +               compatible = "ti,wl1835";
> > +               reg = <2>;
>
> @0 and reg = <2> do not match.




[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux