Convert the bindings for Synaptics RMI4 bus and devices to DT schema. Changes during conversion: 1. Add reset-gpios already used in DTS and mentioned by RMI4 specification. 2. Do not require address/size cells, because without functions (children) they aren't really needed. Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@xxxxxxxxxx> --- Jason, Matthias, Vincent, I put your names as maintainers, because moderately recently you were changing the driver. Let me know if this is okay or you prefer not to maintain the hardware. --- .../bindings/input/rmi4/rmi_2d_sensor.txt | 56 ---- .../bindings/input/rmi4/rmi_f01.txt | 39 --- .../bindings/input/rmi4/rmi_i2c.txt | 61 ---- .../bindings/input/rmi4/rmi_spi.txt | 56 ---- .../devicetree/bindings/input/syna,rmi4.yaml | 271 ++++++++++++++++++ 5 files changed, 271 insertions(+), 212 deletions(-) delete mode 100644 Documentation/devicetree/bindings/input/rmi4/rmi_2d_sensor.txt delete mode 100644 Documentation/devicetree/bindings/input/rmi4/rmi_f01.txt delete mode 100644 Documentation/devicetree/bindings/input/rmi4/rmi_i2c.txt delete mode 100644 Documentation/devicetree/bindings/input/rmi4/rmi_spi.txt create mode 100644 Documentation/devicetree/bindings/input/syna,rmi4.yaml diff --git a/Documentation/devicetree/bindings/input/rmi4/rmi_2d_sensor.txt b/Documentation/devicetree/bindings/input/rmi4/rmi_2d_sensor.txt deleted file mode 100644 index 9afffbdf6e28..000000000000 --- a/Documentation/devicetree/bindings/input/rmi4/rmi_2d_sensor.txt +++ /dev/null @@ -1,56 +0,0 @@ -Synaptics RMI4 2D Sensor Device Binding - -The Synaptics RMI4 core is able to support RMI4 devices using different -transports and different functions. This file describes the device tree -bindings for devices which contain 2D sensors using Function 11 or -Function 12. Complete documentation for transports and other functions -can be found in: -Documentation/devicetree/bindings/input/rmi4. - -RMI4 Function 11 and Function 12 are for 2D touch position sensing. -Additional documentation for F11 can be found at: -http://www.synaptics.com/sites/default/files/511-000136-01-Rev-E-RMI4-Interfacing-Guide.pdf - -Optional Touch Properties: -Description in Documentation/devicetree/bindings/input/touchscreen -- touchscreen-inverted-x -- touchscreen-inverted-y -- touchscreen-swapped-x-y -- touchscreen-x-mm -- touchscreen-y-mm - -Optional Properties: -- syna,clip-x-low: Sets a minimum value for X. -- syna,clip-y-low: Sets a minimum value for Y. -- syna,clip-x-high: Sets a maximum value for X. -- syna,clip-y-high: Sets a maximum value for Y. -- syna,offset-x: Add an offset to X. -- syna,offset-y: Add an offset to Y. -- syna,delta-x-threshold: Set the minimum distance on the X axis required - to generate an interrupt in reduced reporting - mode. -- syna,delta-y-threshold: Set the minimum distance on the Y axis required - to generate an interrupt in reduced reporting - mode. -- syna,sensor-type: Set the sensor type. 1 for touchscreen 2 for touchpad. -- syna,disable-report-mask: Mask for disabling posiiton reporting. Used to - disable reporing absolute position data. -- syna,rezero-wait-ms: Time in miliseconds to wait after issuing a rezero - command. - - -Example of a RMI4 I2C device with F11: -Example: - &i2c1 { - rmi4-i2c-dev@2c { - compatible = "syna,rmi4-i2c"; - - ... - - rmi4-f11@11 { - reg = <0x11>; - touchscreen-inverted-y; - syna,sensor-type = <2>; - }; - }; - }; diff --git a/Documentation/devicetree/bindings/input/rmi4/rmi_f01.txt b/Documentation/devicetree/bindings/input/rmi4/rmi_f01.txt deleted file mode 100644 index 079cad2b6843..000000000000 --- a/Documentation/devicetree/bindings/input/rmi4/rmi_f01.txt +++ /dev/null @@ -1,39 +0,0 @@ -Synaptics RMI4 F01 Device Binding - -The Synaptics RMI4 core is able to support RMI4 devices using different -transports and different functions. This file describes the device tree -bindings for devices which contain Function 1. Complete documentation -for transports and other functions can be found in: -Documentation/devicetree/bindings/input/rmi4. - -Additional documentation for F01 can be found at: -http://www.synaptics.com/sites/default/files/511-000136-01-Rev-E-RMI4-Interfacing-Guide.pdf - -Optional Properties: -- syna,nosleep-mode: If set the device will run at full power without sleeping. - nosleep has 3 modes, 0 will not change the default - setting, 1 will disable nosleep (allow sleeping), - and 2 will enable nosleep (disabling sleep). -- syna,wakeup-threshold: Defines the amplitude of the disturbance to the - background capacitance that will cause the - device to wake from dozing. -- syna,doze-holdoff-ms: The delay to wait after the last finger lift and the - first doze cycle. -- syna,doze-interval-ms: The time period that the device sleeps between finger - activity. - - -Example of a RMI4 I2C device with F01: - Example: - &i2c1 { - rmi4-i2c-dev@2c { - compatible = "syna,rmi4-i2c"; - - ... - - rmi4-f01@1 { - reg = <0x1>; - syna,nosleep-mode = <1>; - }; - }; - }; diff --git a/Documentation/devicetree/bindings/input/rmi4/rmi_i2c.txt b/Documentation/devicetree/bindings/input/rmi4/rmi_i2c.txt deleted file mode 100644 index dcb012f5b3ee..000000000000 --- a/Documentation/devicetree/bindings/input/rmi4/rmi_i2c.txt +++ /dev/null @@ -1,61 +0,0 @@ -Synaptics RMI4 I2C Device Binding - -The Synaptics RMI4 core is able to support RMI4 devices using different -transports and different functions. This file describes the device tree -bindings for devices using the I2C transport driver. Complete documentation -for other transports and functions can be found in -Documentation/devicetree/bindings/input/rmi4. - -Required Properties: -- compatible: syna,rmi4-i2c -- reg: I2C address -- #address-cells: Set to 1 to indicate that the function child nodes - consist of only on uint32 value. -- #size-cells: Set to 0 to indicate that the function child nodes do not - have a size property. - -Optional Properties: -- interrupts: interrupt which the rmi device is connected to. -See Documentation/devicetree/bindings/interrupt-controller/interrupts.txt - -- syna,reset-delay-ms: The number of milliseconds to wait after resetting the - device. - -- syna,startup-delay-ms: The number of milliseconds to wait after powering on - the device. - -- vdd-supply: VDD power supply. -See ../regulator/regulator.txt - -- vio-supply: VIO power supply -See ../regulator/regulator.txt - -Function Parameters: -Parameters specific to RMI functions are contained in child nodes of the rmi device - node. Documentation for the parameters of each function can be found in: -Documentation/devicetree/bindings/input/rmi4/rmi_f*.txt. - - - -Example: - &i2c1 { - rmi4-i2c-dev@2c { - compatible = "syna,rmi4-i2c"; - reg = <0x2c>; - #address-cells = <1>; - #size-cells = <0>; - interrupt-parent = <&gpio>; - interrupts = <4 2>; - - rmi4-f01@1 { - reg = <0x1>; - syna,nosleep-mode = <1>; - }; - - rmi4-f11@11 { - reg = <0x11>; - touchscreen-inverted-y; - syna,sensor-type = <2>; - }; - }; - }; diff --git a/Documentation/devicetree/bindings/input/rmi4/rmi_spi.txt b/Documentation/devicetree/bindings/input/rmi4/rmi_spi.txt deleted file mode 100644 index 632f473db65b..000000000000 --- a/Documentation/devicetree/bindings/input/rmi4/rmi_spi.txt +++ /dev/null @@ -1,56 +0,0 @@ -Synaptics RMI4 SPI Device Binding - -The Synaptics RMI4 core is able to support RMI4 devices using different -transports and different functions. This file describes the device tree -bindings for devices using the SPI transport driver. Complete documentation -for other transports and functions can be found in -Documentation/devicetree/bindings/input/rmi4. - -Required Properties: -- compatible: syna,rmi4-spi -- reg: Chip select address for the device -- #address-cells: Set to 1 to indicate that the function child nodes - consist of only on uint32 value. -- #size-cells: Set to 0 to indicate that the function child nodes do not - have a size property. - -Optional Properties: -- interrupts: interrupt which the rmi device is connected to. -See Documentation/devicetree/bindings/interrupt-controller/interrupts.txt - -- spi-rx-delay-us: microsecond delay after a read transfer. -- spi-tx-delay-us: microsecond delay after a write transfer. - -Function Parameters: -Parameters specific to RMI functions are contained in child nodes of the rmi device - node. Documentation for the parameters of each function can be found in: -Documentation/devicetree/bindings/input/rmi4/rmi_f*.txt. - - - -Example: - spi@7000d800 { - rmi4-spi-dev@0 { - compatible = "syna,rmi4-spi"; - reg = <0x0>; - #address-cells = <1>; - #size-cells = <0>; - spi-max-frequency = <4000000>; - spi-cpha; - spi-cpol; - interrupt-parent = <&gpio>; - interrupts = <TEGRA_GPIO(K, 2) 0x2>; - spi-rx-delay-us = <30>; - - rmi4-f01@1 { - reg = <0x1>; - syna,nosleep-mode = <1>; - }; - - rmi4-f11@11 { - reg = <0x11>; - touchscreen-inverted-y; - syna,sensor-type = <2>; - }; - }; - }; diff --git a/Documentation/devicetree/bindings/input/syna,rmi4.yaml b/Documentation/devicetree/bindings/input/syna,rmi4.yaml new file mode 100644 index 000000000000..286b4d52cea9 --- /dev/null +++ b/Documentation/devicetree/bindings/input/syna,rmi4.yaml @@ -0,0 +1,271 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/input/syna,rmi4.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Synaptics RMI4 compliant devices + +maintainers: + - Jason A. Donenfeld <Jason@xxxxxxxxx> + - Matthias Schiffer <matthias.schiffer@xxxxxxxxxxxxxxx + - Vincent Huang <vincent.huang@xxxxxxxxxxxxxxxx> + +description: | + The Synaptics RMI4 (Register Mapped Interface 4) core is able to support RMI4 + devices using different transports (I2C, SPI) and different functions (e.g. + Function 1, 2D sensors using Function 11 or 12). + +properties: + compatible: + enum: + - syna,rmi4-i2c + - syna,rmi4-spi + + reg: + maxItems: 1 + + '#address-cells': + const: 1 + + '#size-cells': + const: 0 + + interrupts: + maxItems: 1 + + reset-gpios: + maxItems: 1 + description: Active low signal + + spi-cpha: true + spi-cpol: true + + syna,reset-delay-ms: + description: + Delay to wait after resetting the device. + + syna,startup-delay-ms: + description: + Delay to wait after powering on the device. + + vdd-supply: true + vio-supply: true + + rmi4-f01@1: + type: object + additionalProperties: false + description: + Function 1 + + properties: + reg: + maxItems: 1 + + syna,nosleep-mode: + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [0, 1, 2] + description: + If set the device will run at full power without sleeping. nosleep + has 3 modes, 0 will not change the default setting, 1 will disable + nosleep (allow sleeping), and 2 will enable nosleep (disabling + sleep). + + syna,wakeup-threshold: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + Defines the amplitude of the disturbance to the background + capacitance that will cause the device to wake from dozing. + + syna,doze-holdoff-ms: + description: + The delay to wait after the last finger lift and the first doze + cycle. + + syna,doze-interval-ms: + description: + The time period that the device sleeps between finger activity. + + required: + - reg + +patternProperties: + "^rmi4-f1[12]@1[12]$": + type: object + unevaluatedProperties: false + $ref: /schemas/input/touchscreen/touchscreen.yaml# + description: + RMI4 Function 11 and Function 12 are for 2D touch position sensing. + + properties: + reg: + maxItems: 1 + + syna,clip-x-low: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + Minimum value for X. + + syna,clip-y-low: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + Minimum value for Y. + + syna,clip-x-high: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + Maximum value for X. + + syna,clip-y-high: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + Maximum value for Y. + + syna,offset-x: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + Add an offset to X. + + syna,offset-y: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + Add an offset to Y. + + syna,delta-x-threshold: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + Minimum distance on the X axis required to generate an interrupt in + reduced reporting mode. + + syna,delta-y-threshold: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + Minimum distance on the Y axis required to generate an interrupt in + reduced reporting mode. + + syna,sensor-type: + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [1, 2] + description: | + Sensor type: 1 for touchscreen 2 for touchpad. + + syna,disable-report-mask: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + Mask for disabling posiiton reporting. Used to disable reporing + absolute position data. + + syna,rezero-wait-ms: + description: + Time to wait after issuing a rezero command. + + required: + - reg + + "^rmi4-f[0-9a-z]+@[0-9a-z]+$": + type: object + description: + Other functions, not documented yet. + + properties: + reg: + maxItems: 1 + + required: + - reg + +required: + - compatible + - reg + +unevaluatedProperties: false + +allOf: + - $ref: /schemas/spi/spi-peripheral-props.yaml# + + - if: + properties: + compatible: + contains: + const: syna,rmi4-i2c + then: + properties: + spi-rx-delay-us: false + spi-tx-delay-us: false + else: + properties: + syna,reset-delay-ms: false + syna,startup-delay-ms: false + +examples: + - | + #include <dt-bindings/interrupt-controller/irq.h> + + i2c { + #address-cells = <1>; + #size-cells = <0>; + + touchscreen@20 { + compatible = "syna,rmi4-i2c"; + reg = <0x20>; + interrupt-parent = <&gpx1>; + interrupts = <6 IRQ_TYPE_EDGE_FALLING>; + + syna,startup-delay-ms = <100>; + vdd-supply = <&tsp_vdd>; + vio-supply = <&ldo32_reg>; + + pinctrl-0 = <&touch_irq>; + pinctrl-names = "default"; + #address-cells = <1>; + #size-cells = <0>; + + rmi4-f01@1 { + reg = <0x1>; + syna,nosleep-mode = <1>; + }; + + rmi4-f12@12 { + reg = <0x12>; + syna,sensor-type = <1>; + }; + + rmi4-f1a@1a { + reg = <0x1a>; + }; + }; + }; + + - | + #include <dt-bindings/interrupt-controller/irq.h> + + spi { + #address-cells = <1>; + #size-cells = <0>; + + touchscreen@0 { + compatible = "syna,rmi4-spi"; + reg = <0x0>; + interrupt-parent = <&gpx1>; + interrupts = <6 IRQ_TYPE_EDGE_FALLING>; + + spi-max-frequency = <4000000>; + spi-rx-delay-us = <30>; + spi-cpha; + spi-cpol; + + #address-cells = <1>; + #size-cells = <0>; + + rmi4-f01@1 { + reg = <0x1>; + syna,nosleep-mode = <1>; + }; + + rmi4-f11@11 { + reg = <0x11>; + touchscreen-inverted-y; + syna,sensor-type = <2>; + }; + }; + }; -- 2.34.1
