On Thu, Jul 20, 2023 at 12:15 AM Krzysztof Kozlowski <krzysztof.kozlowski@xxxxxxxxxx> wrote: > > On 20/07/2023 00:41, James Hilliard wrote: > > This patch adds support for the Variscite MX6 SoM Carrier Board. > > > > This Carrier-Board has the following : > > - LVDS interface for the VLCD-CAP-GLD-LVDS 7" LCD 800 x 480 touch display > > - HDMI Connector > > - USB Host + USB OTG Connector > > - 10/100/1000 Mbps Ethernet > > - miniPCI-Express slot > > - SD Card connector > > - Audio Headphone/Line In jack connectors > > - S-ATA > > - On-board DMIC > > - RS485 Header > > - CAN bus header > > - SPI header > > - Camera Interfaces header > > - OnBoard RTC with Coin Backup battery socket > > - RS232 Debug Header (IDC10) > > - RS232 DTE > > > > Product Page : https://www.variscite.com/product/single-board-computers/var-mx6customboard > > > > The dts file based on the ones provided by Variscite on their own > > kernel, but adapted for mainline. > > > > Signed-off-by: Gregory CLEMENT <gregory.clement@xxxxxxxxxxx> > > Signed-off-by: James Hilliard <james.hilliard1@xxxxxxxxx> > > --- > > .../devicetree/bindings/arm/fsl.yaml | 1 + > > Please run scripts/checkpatch.pl and fix reported warnings. Some > warnings can be ignored, but the code here looks like it needs a fix. > Feel free to get in touch if the warning is not clear. > > > arch/arm/boot/dts/Makefile | 1 + > > .../arm/boot/dts/imx6q-var-mx6customboard.dts | 279 ++++++++++++++++++ > > 3 files changed, 281 insertions(+) > > create mode 100644 arch/arm/boot/dts/imx6q-var-mx6customboard.dts > > > > diff --git a/Documentation/devicetree/bindings/arm/fsl.yaml b/Documentation/devicetree/bindings/arm/fsl.yaml > > index 15d411084065..0f583852de8a 100644 > > --- a/Documentation/devicetree/bindings/arm/fsl.yaml > > +++ b/Documentation/devicetree/bindings/arm/fsl.yaml > > @@ -298,6 +298,7 @@ properties: > > - udoo,imx6q-udoo # Udoo i.MX6 Quad Board > > - uniwest,imx6q-evi # Uniwest Evi > > - variscite,dt6customboard > > + - variscite,mx6customboard > > - wand,imx6q-wandboard # Wandboard i.MX6 Quad Board > > - ysoft,imx6q-yapp4-crux # i.MX6 Quad Y Soft IOTA Crux board > > - ysoft,imx6q-yapp4-pegasus # i.MX6 Quad Y Soft IOTA Pegasus board > > diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile > > index 59829fc90315..9cfc3d3e91ea 100644 > > --- a/arch/arm/boot/dts/Makefile > > +++ b/arch/arm/boot/dts/Makefile > > @@ -665,6 +665,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \ > > imx6q-udoo.dtb \ > > imx6q-utilite-pro.dtb \ > > imx6q-var-dt6customboard.dtb \ > > + imx6q-var-mx6customboard.dtb \ > > imx6q-vicut1.dtb \ > > imx6q-wandboard.dtb \ > > imx6q-wandboard-revb1.dtb \ > > diff --git a/arch/arm/boot/dts/imx6q-var-mx6customboard.dts b/arch/arm/boot/dts/imx6q-var-mx6customboard.dts > > new file mode 100644 > > index 000000000000..66047dff11ec > > --- /dev/null > > +++ b/arch/arm/boot/dts/imx6q-var-mx6customboard.dts > > @@ -0,0 +1,279 @@ > > +// SPDX-License-Identifier: GPL-2.0+ > > +/* > > + * Support for Variscite MX6 Carrier-board > > + * > > + * Copyright 2016 Variscite, Ltd. All Rights Reserved > > + * Copyright 2022 Bootlin > > + */ > > + > > +/dts-v1/; > > + > > +#include "imx6qdl-var-som.dtsi" > > +#include <dt-bindings/pwm/pwm.h> > > + > > +/ { > > + model = "Variscite i.MX6 QUAD/DUAL VAR-SOM-MX6 Custom Board"; > > + compatible = "variscite,mx6customboard", "fsl,imx6q"; > > Where is the SoM compatible? I mostly just copied this from the DART-MX6 device tree which is another variscite imx6q based modular SoM custom board combination: https://github.com/torvalds/linux/blob/v6.5-rc2/arch/arm/boot/dts/nxp/imx/imx6q-var-dt6customboard.dts#L17 The terminology is a bit confusing in general here, variscite has 2 families of pin2pin modules, the "VAR-SOM" and the "DART" family. https://www.variscite.com/variscite-pin2pin-system-on-module-families/ Within each connector family there are then multiple SoM boards that can be used with the same carrier boards(ie the Custom Board carrier board like the evaluation kit) although they are often bundled together with specific boards in practice. So the existing DART-MX6 I think uses the same SoC but is in a different family and as such has a different carrier board. However as the relation between the SoM and the carrier board is effectively the same, I just copied the way compatibile is being set there for the VAR-SOM-MX6 from the existing DART-MX6 custom board device tree. I think this roughly represents the SoM board device tree associations as I'm understanding them: pin2pin Family: DART SoM: https://www.variscite.com/product/system-on-module-som/cortex-a9/dart-mx6-cpu-freescale-imx6/ SoM part: DART-MX6 SoM device tree: imx6qdl-var-dart.dtsi SoM SoC: imx6q Board: https://www.variscite.com/product/single-board-computers/dt6customboard/ Board device tree: imx6q-var-dt6customboard.dts Board compatible: compatible = "variscite,dt6customboard", "fsl,imx6q"; pin2pin Family: VAR-SOM SoM: https://www.variscite.com/product/system-on-module-som/cortex-a9/var-som-mx6-cpu-freescale-imx6/ SoM part: VAR-SOM-MX6 SoM device tree: imx6qdl-var-som.dtsi SoM SoC: imx6q Board: mx6customboard https://www.variscite.com/product/single-board-computers/var-mx6customboard/ Board device tree: imx6q-var-mx6customboard.dts Board compatible: compatible = "variscite,mx6customboard", "fsl,imx6q"; What's confusing here is that the DART-MX6 is also described as a SoM: "DART-MX6 from Variscite is the smallest System on Module (SoM) / Computer on Module (CoM) supporting NXP/Freescale’s i.MX6 Quad and Dual-core Cortex-A9™ processor" So we have a "DART-MX6" SoM part which corresponds to the "VAR-SOM-MX6" SoM part, with both being SoM's but only one("VAR-SOM-MX6") having SoM in the actual part name. Does the compatible section for imx6qdl-var-dart.dtsi look correct? I'm not sure what exactly a "SoM compatible" should look like here as SoM is both a generic term(used to describe by both the "DART-MX6" and "VAR-SOM-MX6" parts) as well as term used within a part(used in the part for "VAR-SOM-MX6" as well as other SoM's in the "VAR-SOM" family but not the "DART-MX6" part or other SoM's in the "DART" family). > > Best regards, > Krzysztof >
