The Loongson-2's power management controller was ACPI, supports ACPI
S2Idle (Suspend To Idle), ACPI S3 (Suspend To RAM), ACPI S4 (Suspend To
Disk), ACPI S5 (Soft Shutdown) and supports multiple wake-up methods
(USB, GMAC, PWRBTN, etc.). This driver was to add power management
controller support that base on dts for Loongson-2 series SoCs.
Co-developed-by: Liu Yun <liuyun@xxxxxxxxxxx>
Signed-off-by: Liu Yun <liuyun@xxxxxxxxxxx>
Co-developed-by: Liu Peibao <liupeibao@xxxxxxxxxxx>
Signed-off-by: Liu Peibao <liupeibao@xxxxxxxxxxx>
Signed-off-by: Yinbo Zhu <zhuyinbo@xxxxxxxxxxx>
---
MAINTAINERS | 1 +
drivers/soc/loongson/Kconfig | 10 ++
drivers/soc/loongson/Makefile | 1 +
drivers/soc/loongson/loongson2_pm.c | 215 ++++++++++++++++++++++++++++
4 files changed, 227 insertions(+)
create mode 100644 drivers/soc/loongson/loongson2_pm.c
diff --git a/MAINTAINERS b/MAINTAINERS
index bcd05f1fa5c1..7c4ad0cbaeff 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -12195,6 +12195,7 @@ M: Yinbo Zhu <zhuyinbo@xxxxxxxxxxx>
L: linux-pm@xxxxxxxxxxxxxxx
S: Maintained
F: Documentation/devicetree/bindings/soc/loongson/loongson,ls2k-pmc.yaml
+F: drivers/soc/loongson/loongson2_pm.c
LOONGSON-2 SOC SERIES PINCTRL DRIVER
M: zhanghongchen <zhanghongchen@xxxxxxxxxxx>
diff --git a/drivers/soc/loongson/Kconfig b/drivers/soc/loongson/Kconfig
index 707f56358dc4..4f3ce9eb7520 100644
--- a/drivers/soc/loongson/Kconfig
+++ b/drivers/soc/loongson/Kconfig
@@ -16,3 +16,13 @@ config LOONGSON2_GUTS
SoCs. Initially only reading SVR and registering soc device are
supported. Other guts accesses, such as reading firmware configuration
by default, should eventually be added into this driver as well.
+
+config LOONGSON2_PM
+ bool "Loongson-2 SoC Power Management Controller Driver"
+ depends on LOONGARCH && OF
+ help
+ The Loongson-2's power management controller was ACPI, supports ACPI
+ S2Idle (Suspend To Idle), ACPI S3 (Suspend To RAM), ACPI S4 (Suspend To
+ Disk), ACPI S5 (Soft Shutdown) and supports multiple wake-up methods
+ (USB, GMAC, PWRBTN, etc.). This driver was to add power management
+ controller support that base on dts for Loongson-2 series SoCs.
diff --git a/drivers/soc/loongson/Makefile b/drivers/soc/loongson/Makefile
index 263c486df638..4118f50f55e2 100644
--- a/drivers/soc/loongson/Makefile
+++ b/drivers/soc/loongson/Makefile
@@ -4,3 +4,4 @@
#
obj-$(CONFIG_LOONGSON2_GUTS) += loongson2_guts.o
+obj-$(CONFIG_LOONGSON2_PM) += loongson2_pm.o
diff --git a/drivers/soc/loongson/loongson2_pm.c b/drivers/soc/loongson/loongson2_pm.c
new file mode 100644
index 000000000000..cd022a1d5b33
--- /dev/null
+++ b/drivers/soc/loongson/loongson2_pm.c
@@ -0,0 +1,215 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Loongson-2 PM Support
+ *
+ * Copyright (C) 2023 Loongson Technology Corporation Limited
+ */
+
+#include <linux/io.h>
+#include <linux/of.h>
+#include <linux/init.h>
+#include <linux/input.h>
+#include <linux/suspend.h>
+#include <linux/interrupt.h>
+#include <linux/pm_wakeirq.h>
+#include <linux/platform_device.h>
+#include <asm/bootinfo.h>
+#include <asm/suspend.h>
+
+#define LOONGSON2_PM1_CNT_REG 0x14
+#define LOONGSON2_PM1_STS_REG 0x0c
+#define LOONGSON2_PM1_ENA_REG 0x10
+#define LOONGSON2_GPE0_STS_REG 0x28
+#define LOONGSON2_GPE0_ENA_REG 0x2c
+
+#define LOONGSON2_PM1_PWRBTN_STS BIT(8)
+#define LOONGSON2_PM1_PCIEXP_WAKE_STS BIT(14)
+#define LOONGSON2_PM1_WAKE_STS BIT(15)
+#define LOONGSON2_PM1_CNT_INT_EN BIT(0)
+#define LOONGSON2_PM1_PWRBTN_EN LOONGSON2_PM1_PWRBTN_STS
+
+static struct loongson2_pm {
+ void __iomem *base;
+ struct input_dev *dev;
+ bool suspended;
+} loongson2_pm;
+
+#define loongson2_pm_readw(reg) readw(loongson2_pm.base + reg)
+#define loongson2_pm_readl(reg) readl(loongson2_pm.base + reg)
+#define loongson2_pm_writew(val, reg) writew(val, loongson2_pm.base + reg)
+#define loongson2_pm_writel(val, reg) writel(val, loongson2_pm.base + reg)
+
+static void loongson2_pm_status_clear(void)
+{
+ u16 value;
+
+ value = loongson2_pm_readw(LOONGSON2_PM1_STS_REG);
+ value |= (LOONGSON2_PM1_PWRBTN_STS | LOONGSON2_PM1_PCIEXP_WAKE_STS |
+ LOONGSON2_PM1_WAKE_STS);
+ loongson2_pm_writew(value, LOONGSON2_PM1_STS_REG);
+ loongson2_pm_writel(loongson2_pm_readl(LOONGSON2_GPE0_STS_REG), LOONGSON2_GPE0_STS_REG);
+}
+
+static void loongson2_pm_irq_enable(void)
+{
+ u16 value;
+
+ value = loongson2_pm_readw(LOONGSON2_PM1_CNT_REG);
+ value |= LOONGSON2_PM1_CNT_INT_EN;
+ loongson2_pm_writew(value, LOONGSON2_PM1_CNT_REG);
+
+ value = loongson2_pm_readw(LOONGSON2_PM1_ENA_REG);
+ value |= LOONGSON2_PM1_PWRBTN_EN;
+ loongson2_pm_writew(value, LOONGSON2_PM1_ENA_REG);
+}
+
+static int loongson2_suspend_enter(suspend_state_t state)
+{
+ loongson2_pm_status_clear();
+ loongarch_common_suspend();
+ loongarch_suspend_enter();
+ loongarch_common_resume();
+ loongson2_pm_irq_enable();
+ pm_set_resume_via_firmware();
+
+ return 0;
+}
+
+static int loongson2_suspend_begin(suspend_state_t state)
+{
+ pm_set_suspend_via_firmware();
+
+ return 0;
+}
+
+static int loongson2_suspend_valid_state(suspend_state_t state)
+{
+ return (state == PM_SUSPEND_MEM);
+}
+
+static const struct platform_suspend_ops loongson2_suspend_ops = {
+ .valid = loongson2_suspend_valid_state,
+ .begin = loongson2_suspend_begin,
+ .enter = loongson2_suspend_enter,
+};
+
+static int loongson2_power_button_init(struct device *dev, int irq)
+{
+ int ret;
+ struct input_dev *button;
+
+ button = input_allocate_device();
+ if (!dev)
+ return -ENOMEM;
+
+ button->name = "Power Button";
+ button->phys = "pm/button/input0";
+ button->id.bustype = BUS_HOST;
+ button->dev.parent = NULL;
+ input_set_capability(button, EV_KEY, KEY_POWER);
+
+ ret = input_register_device(button);
+ if (ret)
+ goto free_dev;
+
+ dev_pm_set_wake_irq(&button->dev, irq);
+ device_set_wakeup_capable(&button->dev, true);
+ device_set_wakeup_enable(&button->dev, true);
+
+ loongson2_pm.dev = button;
+ dev_info(dev, "Power Button: Init successful!\n");
+
+ return 0;
+
+free_dev:
+ input_free_device(button);
+
+ return ret;
+}
+
+static irqreturn_t loongson2_pm_irq_handler(int irq, void *dev_id)
+{
+ u16 status = loongson2_pm_readw(LOONGSON2_PM1_STS_REG);
+
+ if (!loongson2_pm.suspended && (status & LOONGSON2_PM1_PWRBTN_STS)) {
+ pr_info("Power Button pressed...\n");
+ input_report_key(loongson2_pm.dev, KEY_POWER, 1);
+ input_sync(loongson2_pm.dev);
+ input_report_key(loongson2_pm.dev, KEY_POWER, 0);
+ input_sync(loongson2_pm.dev);
+ }
+
+ loongson2_pm_status_clear();
+
+ return IRQ_HANDLED;
+}
+
+static int __maybe_unused loongson2_pm_suspend(struct device *dev)
+{
+ loongson2_pm.suspended = true;
+
+ return 0;
+}
+
+static int __maybe_unused loongson2_pm_resume(struct device *dev)
+{
+ loongson2_pm.suspended = false;
+
+ return 0;
+}
+static SIMPLE_DEV_PM_OPS(loongson2_pm_ops, loongson2_pm_suspend, loongson2_pm_resume);
+
+static int loongson2_pm_probe(struct platform_device *pdev)
+{
+ int irq, retval;
+ u64 suspend_addr;
+ struct device *dev = &pdev->dev;
+
+ loongson2_pm.base = devm_platform_ioremap_resource(pdev, 0);
+ if (IS_ERR(loongson2_pm.base))
+ return PTR_ERR(loongson2_pm.base);
+
+ irq = platform_get_irq(pdev, 0);
+ if (irq < 0)
+ return irq;
+
+ if (!device_property_read_u64(dev, "loongson,suspend-address", &suspend_addr))
+ loongson_sysconf.suspend_addr = (u64)phys_to_virt(suspend_addr);
+ else
+ dev_err(dev, "No loongson,suspend-address, could not support S3!\n");
+
+ if (loongson2_power_button_init(dev, irq))
+ return -EINVAL;
+
+ retval = devm_request_irq(&pdev->dev, irq, loongson2_pm_irq_handler,
+ IRQF_SHARED, "pm_irq", &loongson2_pm);
+ if (retval)
+ return retval;
+
+ loongson2_pm_irq_enable();
+ loongson2_pm_status_clear();
+
+ if (loongson_sysconf.suspend_addr)
+ suspend_set_ops(&loongson2_suspend_ops);
+
+ return 0;
+}
+
+static const struct of_device_id loongson2_pm_match[] = {
+ { .compatible = "loongson,ls2k1000-pmc", },
+ { .compatible = "loongson,ls2k0500-pmc", },
+ {},
+};
+
+static struct platform_driver loongson2_pm_driver = {
+ .driver = {
+ .name = "ls2k-pm",
+ .pm = &loongson2_pm_ops,
+ .of_match_table = loongson2_pm_match,
+ },
+ .probe = loongson2_pm_probe,
+};
+module_platform_driver(loongson2_pm_driver);
+
+MODULE_DESCRIPTION("Loongson-2 PM driver");
+MODULE_LICENSE("GPL");
