Change PM8018 node labels to start with pm8018_ prefix, following other
Qualcomm PMIC device nodes.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@xxxxxxxxxx>
---
arch/arm/boot/dts/qcom/qcom-mdm9615-wp8548.dtsi | 2 +-
arch/arm/boot/dts/qcom/qcom-mdm9615.dtsi | 14 +++++++-------
2 files changed, 8 insertions(+), 8 deletions(-)
diff --git a/arch/arm/boot/dts/qcom/qcom-mdm9615-wp8548.dtsi b/arch/arm/boot/dts/qcom/qcom-mdm9615-wp8548.dtsi
index 92c8003dac25..dac3aa793f71 100644
--- a/arch/arm/boot/dts/qcom/qcom-mdm9615-wp8548.dtsi
+++ b/arch/arm/boot/dts/qcom/qcom-mdm9615-wp8548.dtsi
@@ -76,7 +76,7 @@ reset-out-pins {
};
};
-&pmicgpio {
+&pm8018_gpio {
usb_vbus_5v_pins: usb-vbus-5v-state {
pins = "gpio4";
function = "normal";
diff --git a/arch/arm/boot/dts/qcom/qcom-mdm9615.dtsi b/arch/arm/boot/dts/qcom/qcom-mdm9615.dtsi
index b40c52ddf9b4..e79582c6220b 100644
--- a/arch/arm/boot/dts/qcom/qcom-mdm9615.dtsi
+++ b/arch/arm/boot/dts/qcom/qcom-mdm9615.dtsi
@@ -246,7 +246,7 @@ qcom,ssbi@500000 {
reg = <0x500000 0x1000>;
qcom,controller-type = "pmic-arbiter";
- pmicintc: pmic {
+ pm8018: pmic {
compatible = "qcom,pm8018", "qcom,pm8921";
interrupts = <GIC_PPI 226 IRQ_TYPE_LEVEL_HIGH>;
#interrupt-cells = <2>;
@@ -257,38 +257,38 @@ pmicintc: pmic {
pwrkey@1c {
compatible = "qcom,pm8018-pwrkey", "qcom,pm8921-pwrkey";
reg = <0x1c>;
- interrupt-parent = <&pmicintc>;
+ interrupt-parent = <&pm8018>;
interrupts = <50 IRQ_TYPE_EDGE_RISING>,
<51 IRQ_TYPE_EDGE_RISING>;
debounce = <15625>;
pull-up;
};
- pmicmpp: mpps@50 {
+ pm8018_mpps: mpps@50 {
compatible = "qcom,pm8018-mpp", "qcom,ssbi-mpp";
interrupt-controller;
#interrupt-cells = <2>;
reg = <0x50>;
gpio-controller;
#gpio-cells = <2>;
- gpio-ranges = <&pmicmpp 0 0 6>;
+ gpio-ranges = <&pm8018_mpps 0 0 6>;
};
rtc@11d {
compatible = "qcom,pm8018-rtc", "qcom,pm8921-rtc";
- interrupt-parent = <&pmicintc>;
+ interrupt-parent = <&pm8018>;
interrupts = <39 IRQ_TYPE_EDGE_RISING>;
reg = <0x11d>;
allow-set-time;
};
- pmicgpio: gpio@150 {
+ pm8018_gpio: gpio@150 {
compatible = "qcom,pm8018-gpio", "qcom,ssbi-gpio";
reg = <0x150>;
interrupt-controller;
#interrupt-cells = <2>;
gpio-controller;
- gpio-ranges = <&pmicgpio 0 0 6>;
+ gpio-ranges = <&pm8018_gpio 0 0 6>;
#gpio-cells = <2>;
};
};
--
2.39.2
