[PATCH 7/9] regulator: mt6358: Add output voltage fine tuning to fixed regulators

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



The "fixed" LDO regulators found on the MT6358 and MT6366 PMICs have
either no voltage selection register, or only one valid setting.
However these do have a fine voltage calibration setting that can
slightly boost the output voltage from 0 mV to 100 mV, in 10 mV
increments.

Add support for this by changing these into linear range regulators.

Signed-off-by: Chen-Yu Tsai <wenst@xxxxxxxxxxxx>
---
 drivers/regulator/mt6358-regulator.c | 15 +++++++++++++--
 1 file changed, 13 insertions(+), 2 deletions(-)

diff --git a/drivers/regulator/mt6358-regulator.c b/drivers/regulator/mt6358-regulator.c
index 31a16fb28ecd..26060909cf90 100644
--- a/drivers/regulator/mt6358-regulator.c
+++ b/drivers/regulator/mt6358-regulator.c
@@ -123,10 +123,13 @@ struct mt6358_regulator_info {
 		.type = REGULATOR_VOLTAGE,	\
 		.id = MT6358_ID_##vreg,	\
 		.owner = THIS_MODULE,	\
-		.n_voltages = 1,	\
+		.n_voltages = 11,	\
+		.vsel_reg = MT6358_##vreg##_ANA_CON0,	\
+		.vsel_mask = GENMASK(3, 0),	\
 		.enable_reg = enreg,	\
 		.enable_mask = BIT(enbit),	\
 		.min_uV = volt,	\
+		.uV_step = 10000, \
 	},	\
 	.status_reg = MT6358_LDO_##vreg##_CON1,	\
 	.qi = BIT(15),							\
@@ -219,10 +222,13 @@ struct mt6358_regulator_info {
 		.type = REGULATOR_VOLTAGE,	\
 		.id = MT6366_ID_##vreg,	\
 		.owner = THIS_MODULE,	\
-		.n_voltages = 1,	\
+		.n_voltages = 11,	\
+		.vsel_reg = MT6358_##vreg##_ANA_CON0,	\
+		.vsel_mask = GENMASK(3, 0),	\
 		.enable_reg = enreg,	\
 		.enable_mask = BIT(enbit),	\
 		.min_uV = volt,	\
+		.uV_step = 10000, \
 	},	\
 	.status_reg = MT6358_LDO_##vreg##_CON1,	\
 	.qi = BIT(15),							\
@@ -476,8 +482,13 @@ static const struct regulator_ops mt6358_volt_table_ops = {
 	.get_status = mt6358_get_status,
 };
 
+/* "Fixed" LDOs with output voltage calibration +0 ~ +10 mV */
 static const struct regulator_ops mt6358_volt_fixed_ops = {
 	.list_voltage = regulator_list_voltage_linear,
+	.map_voltage = regulator_map_voltage_linear,
+	.set_voltage_sel = regulator_set_voltage_sel_regmap,
+	.get_voltage_sel = mt6358_get_buck_voltage_sel,
+	.set_voltage_time_sel = regulator_set_voltage_time_sel,
 	.enable = regulator_enable_regmap,
 	.disable = regulator_disable_regmap,
 	.is_enabled = regulator_is_enabled_regmap,
-- 
2.41.0.162.gfafddb0af9-goog




[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux