Re: [PATCH 3/6] media: dt-bindings: mediatek,vcodec: Remove VDEC_SYS for mt8183

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On 05/06/2023 18:20, Nícolas F. R. A. Prado wrote:
> The binding expects the first register space to be VDEC_SYS. But on
> mt8183, which uses the stateless decoders, this space is used only for
> controlling clocks and resets, which are better described as separate
> clock-controller and reset-controller nodes.
> 
> In fact, in mt8173's devicetree there are already such separate
> clock-controller nodes, which cause duplicate addresses between the
> vdecsys node and the vcodec node. But for this SoC, since the stateful
> decoder code makes other uses of the VDEC_SYS register space, it's not
> straightforward to remove it.
> 
> In order to avoid the same address conflict to happen on mt8183,
> since the only current use of the VDEC_SYS register space in
> the driver is to read the status of a clock that indicates the hardware
> is active, remove the VDEC_SYS register space from the binding and
> describe an extra clock that will be used to directly check the hardware
> status.
> 
> Also add reg-names to be able to tell that this new register schema is
> used, so the driver can keep backward compatibility.
> 
> Signed-off-by: Nícolas F. R. A. Prado <nfraprado@xxxxxxxxxxxxx>
> ---
> 
>  .../media/mediatek,vcodec-decoder.yaml        | 29 +++++++++++++++++--
>  1 file changed, 27 insertions(+), 2 deletions(-)
> 
> diff --git a/Documentation/devicetree/bindings/media/mediatek,vcodec-decoder.yaml b/Documentation/devicetree/bindings/media/mediatek,vcodec-decoder.yaml
> index 6447e6c86f29..36a53b2484d6 100644
> --- a/Documentation/devicetree/bindings/media/mediatek,vcodec-decoder.yaml
> +++ b/Documentation/devicetree/bindings/media/mediatek,vcodec-decoder.yaml
> @@ -21,17 +21,21 @@ properties:
>        - mediatek,mt8183-vcodec-dec
>  
>    reg:
> +    minItems: 11
>      maxItems: 12
>  
> +  reg-names:
> +    minItems: 11

maxItems

> +
>    interrupts:
>      maxItems: 1
>  
>    clocks:
> -    minItems: 1
> +    minItems: 2

It does not make any sense. Just two patches ago you made it 1! Don't
add incorrect values which are immediately changed in the same patchset.

>      maxItems: 8
>  
>    clock-names:
> -    minItems: 1
> +    minItems: 2
>      maxItems: 8
>  
>    assigned-clocks: true
> @@ -84,6 +88,24 @@ allOf:
>          clock-names:
>            items:
>              - const: vdec
> +            - const: active
> +
> +        reg:
> +          maxItems: 11
> +
> +        reg-names:
> +          items:
> +            - const: misc
> +            - const: ld
> +            - const: top
> +            - const: cm
> +            - const: ad
> +            - const: av
> +            - const: pp
> +            - const: hwd
> +            - const: hwq
> +            - const: hwb
> +            - const: hwg
>  
>    - if:
>        properties:
> @@ -108,6 +130,9 @@ allOf:
>              - const: venc_lt_sel
>              - const: vdec_bus_clk_src
>  
> +        reg:
> +          minItems: 12

so max can be 1000?



Best regards,
Krzysztof




[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux