CAN instances 3 and 5 in the main domain are brought on the common processor board through header J27 and J28. The CAN High and Low lines from the SoC are routed through a mux on the SoM. The select lines need to be set for the CAN signals to get connected to the transceivers on the common processor board. Threfore, add respective mux, transceiver dt nodes to add support for these CAN instances. Signed-off-by: Bhavya Kapoor <b-kapoor@xxxxxx> --- Changelog v2->v3: Removed tiL6.1 subject prefix Link to v2 : https://lore.kernel.org/all/20230523085021.22524-1-b-kapoor@xxxxxx/ .../dts/ti/k3-j721s2-common-proc-board.dts | 46 +++++++++++++++++++ arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi | 12 +++++ 2 files changed, 58 insertions(+) diff --git a/arch/arm64/boot/dts/ti/k3-j721s2-common-proc-board.dts b/arch/arm64/boot/dts/ti/k3-j721s2-common-proc-board.dts index a7aa6cf08acd..f07663bbea16 100644 --- a/arch/arm64/boot/dts/ti/k3-j721s2-common-proc-board.dts +++ b/arch/arm64/boot/dts/ti/k3-j721s2-common-proc-board.dts @@ -27,6 +27,8 @@ aliases { can0 = &main_mcan16; can1 = &mcu_mcan0; can2 = &mcu_mcan1; + can3 = &main_mcan3; + can4 = &main_mcan5; }; evm_12v0: fixedregulator-evm12v0 { @@ -107,6 +109,22 @@ transceiver2: can-phy2 { standby-gpios = <&wkup_gpio0 2 GPIO_ACTIVE_HIGH>; }; + transceiver3: can-phy3 { + compatible = "ti,tcan1043"; + #phy-cells = <0>; + max-bitrate = <5000000>; + standby-gpios = <&exp2 7 GPIO_ACTIVE_LOW>; + enable-gpios = <&exp2 6 GPIO_ACTIVE_HIGH>; + mux-states = <&mux0 1>; + }; + + transceiver4: can-phy4 { + compatible = "ti,tcan1042"; + #phy-cells = <0>; + max-bitrate = <5000000>; + standby-gpios = <&exp_som 7 GPIO_ACTIVE_HIGH>; + mux-states = <&mux1 1>; + }; }; &main_pmx0 { @@ -144,6 +162,20 @@ vdd_sd_dv_pins_default: vdd-sd-dv-pins-default { J721S2_IOPAD(0x020, PIN_INPUT, 7) /* (AA23) MCAN15_RX.GPIO0_8 */ >; }; + + main_mcan3_pins_default: main-mcan3-pins-default { + pinctrl-single,pins = < + J721S2_IOPAD(0x080, PIN_INPUT, 0) /* (U26) MCASP0_AXR4.MCAN3_RX */ + J721S2_IOPAD(0x07c, PIN_OUTPUT, 0) /* (T27) MCASP0_AXR3.MCAN3_TX */ + >; + }; + + main_mcan5_pins_default: main-mcan5-pins-default { + pinctrl-single,pins = < + J721S2_IOPAD(0x03c, PIN_INPUT, 0) /* (U27) MCASP0_AFSX.MCAN5_RX */ + J721S2_IOPAD(0x038, PIN_OUTPUT, 0) /* (AB28) MCASP0_ACLKX.MCAN5_TX */ + >; + }; }; &wkup_pmx0 { @@ -309,3 +341,17 @@ &mcu_mcan1 { pinctrl-0 = <&mcu_mcan1_pins_default>; phys = <&transceiver2>; }; + +&main_mcan3 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&main_mcan3_pins_default>; + phys = <&transceiver3>; +}; + +&main_mcan5 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&main_mcan5_pins_default>; + phys = <&transceiver4>; +}; diff --git a/arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi b/arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi index 6930efff8a5a..e74bc5141903 100644 --- a/arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi +++ b/arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi @@ -31,6 +31,18 @@ secure_ddr: optee@9e800000 { }; }; + mux0: mux-controller0 { + compatible = "gpio-mux"; + #mux-state-cells = <1>; + mux-gpios = <&exp_som 1 GPIO_ACTIVE_HIGH>; + }; + + mux1: mux-controller1 { + compatible = "gpio-mux"; + #mux-state-cells = <1>; + mux-gpios = <&exp_som 2 GPIO_ACTIVE_HIGH>; + }; + transceiver0: can-phy0 { /* standby pin has been grounded by default */ compatible = "ti,tcan1042"; -- 2.39.2
