Re: [RFC PATCH v2 1/2] dt-bindings: sc16is7xx: Add property to change GPIO function

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Thu, May 18, 2023 at 09:29:06AM -0400, Hugo Villeneuve wrote:
> From: Hugo Villeneuve <hvilleneuve@xxxxxxxxxxxx>
> 
> Some variants in this series of uart controllers have GPIO pins that
> are shared between GPIO and modem control lines.
> 
> The pin mux mode (GPIO or modem control lines) can be set for each
> ports (channels) supported by the variant.
> 
> This adds a property to the device tree to set the GPIO pin mux to
> modem control lines on selected ports if needed.
> 
> Signed-off-by: Hugo Villeneuve <hvilleneuve@xxxxxxxxxxxx>

On the basis of similarity to existing properties due to my lack of
understanding of the hardware it'll have to be an Ack. Hopefully Greg &
Co. have more specific insight.
Acked-by: Conor Dooley <conor.dooley@xxxxxxxxxxxxx>

Thanks,
Conor.

> ---
> v1 -> v2: Add nxp vendor prefix
>           Add git base-commit
> 
>  .../bindings/serial/nxp,sc16is7xx.txt         | 28 +++++++++++++++++++
>  1 file changed, 28 insertions(+)
> 
> diff --git a/Documentation/devicetree/bindings/serial/nxp,sc16is7xx.txt b/Documentation/devicetree/bindings/serial/nxp,sc16is7xx.txt
> index 0fa8e3e43bf8..23a81c83f012 100644
> --- a/Documentation/devicetree/bindings/serial/nxp,sc16is7xx.txt
> +++ b/Documentation/devicetree/bindings/serial/nxp,sc16is7xx.txt
> @@ -23,6 +23,9 @@ Optional properties:
>      1 = active low.
>  - irda-mode-ports: An array that lists the indices of the port that
>  		   should operate in IrDA mode.
> +- nxp,modem-control-line-ports: An array that lists the indices of the port that
> +				should have shared GPIO lines configured as modem
> +				control lines.
>  
>  Example:
>          sc16is750: sc16is750@51 {
> @@ -35,6 +38,17 @@ Example:
>                  #gpio-cells = <2>;
>          };
>  
> +	sc16is752: sc16is752@54 {
> +		compatible = "nxp,sc16is752";
> +		reg = <0x54>;
> +		clocks = <&clk20m>;
> +		interrupt-parent = <&gpio3>;
> +		interrupts = <7 IRQ_TYPE_EDGE_FALLING>;
> +		nxp,modem-control-line-ports = <1>; /* Port 1 as modem control lines */
> +		gpio-controller; /* Port 0 as GPIOs */
> +		#gpio-cells = <2>;
> +	};
> +
>  * spi as bus
>  
>  Required properties:
> @@ -59,6 +73,9 @@ Optional properties:
>      1 = active low.
>  - irda-mode-ports: An array that lists the indices of the port that
>  		   should operate in IrDA mode.
> +- nxp,modem-control-line-ports: An array that lists the indices of the port that
> +				should have shared GPIO lines configured as modem
> +				control lines.
>  
>  Example:
>  	sc16is750: sc16is750@0 {
> @@ -70,3 +87,14 @@ Example:
>  		gpio-controller;
>  		#gpio-cells = <2>;
>  	};
> +
> +	sc16is752: sc16is752@0 {
> +		compatible = "nxp,sc16is752";
> +		reg = <0>;
> +		clocks = <&clk20m>;
> +		interrupt-parent = <&gpio3>;
> +		interrupts = <7 IRQ_TYPE_EDGE_FALLING>;
> +		nxp,modem-control-line-ports = <1>; /* Port 1 as modem control lines */
> +		gpio-controller; /* Port 0 as GPIOs */
> +		#gpio-cells = <2>;
> +	};
> 
> base-commit: 4d6d4c7f541d7027beed4fb86eb2c451bd8d6fff
> -- 
> 2.30.2
> 

Attachment: signature.asc
Description: PGP signature


[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux