Enable Display Subsystem with Visionox VTDR6130 Panel (same as on MTP8550). Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@xxxxxxxxxx> --- Context in the patch depends on: 1. https://lore.kernel.org/linux-arm-msm/20230516133011.108093-1-krzysztof.kozlowski@xxxxxxxxxx/T/#t 2. https://lore.kernel.org/linux-arm-msm/20230512160452.206585-1-krzysztof.kozlowski@xxxxxxxxxx/ --- arch/arm64/boot/dts/qcom/sm8550-qrd.dts | 76 +++++++++++++++++++++++++ 1 file changed, 76 insertions(+) diff --git a/arch/arm64/boot/dts/qcom/sm8550-qrd.dts b/arch/arm64/boot/dts/qcom/sm8550-qrd.dts index 30b36a149125..03bf6bc2db4d 100644 --- a/arch/arm64/boot/dts/qcom/sm8550-qrd.dts +++ b/arch/arm64/boot/dts/qcom/sm8550-qrd.dts @@ -420,6 +420,10 @@ vreg_l3g_1p2: ldo3 { }; }; +&dispcc { + status = "okay"; +}; + &gcc { clocks = <&bi_tcxo_div2>, <&sleep_clk>, <&pcie0_phy>, @@ -431,6 +435,50 @@ &gcc { <&usb_dp_qmpphy QMP_USB43DP_USB3_PIPE_CLK>; }; +&mdss { + status = "okay"; +}; + +&mdss_dsi0 { + vdda-supply = <&vreg_l3e_1p2>; + status = "okay"; + + panel@0 { + compatible = "visionox,vtdr6130"; + reg = <0>; + + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&sde_dsi_active>, <&sde_te_active>; + pinctrl-1 = <&sde_dsi_suspend>, <&sde_te_suspend>; + + vddio-supply = <&vreg_l12b_1p8>; + vci-supply = <&vreg_l13b_3p0>; + vdd-supply = <&vreg_l11b_1p2>; + + reset-gpios = <&tlmm 133 GPIO_ACTIVE_LOW>; + + port { + panel0_in: endpoint { + remote-endpoint = <&mdss_dsi0_out>; + }; + }; + }; +}; + +&mdss_dsi0_out { + remote-endpoint = <&panel0_in>; + data-lanes = <0 1 2 3>; +}; + +&mdss_dsi0_phy { + vdds-supply = <&vreg_l1e_0p88>; + status = "okay"; +}; + +&mdss_mdp { + status = "okay"; +}; + &pcie_1_phy_aux_clk { status = "disabled"; }; @@ -532,6 +580,34 @@ wcd_tx: codec@0,3 { &tlmm { gpio-reserved-ranges = <32 8>; + sde_dsi_active: sde-dsi-active-state { + pins = "gpio133"; + function = "gpio"; + drive-strength = <8>; + bias-disable; + }; + + sde_dsi_suspend: sde-dsi-suspend-state { + pins = "gpio133"; + function = "gpio"; + drive-strength = <2>; + bias-pull-down; + }; + + sde_te_active: sde-te-active-state { + pins = "gpio86"; + function = "mdp_vsync"; + drive-strength = <2>; + bias-pull-down; + }; + + sde_te_suspend: sde-te-suspend-state { + pins = "gpio86"; + function = "mdp_vsync"; + drive-strength = <2>; + bias-pull-down; + }; + wcd_default: wcd-reset-n-active-state { pins = "gpio108"; function = "gpio"; -- 2.34.1
