Re: [PATCH] ASoC: dt-bindings: nau8825: Convert to dtschema

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On 5/9/2023 2:22 PM, Krzysztof Kozlowski wrote:
On 09/05/2023 07:10, David Lin wrote:
Convert the NAU8825 audio CODEC bindings to DT schema.

Signed-off-by: David Lin <CTLIN0@xxxxxxxxxxx>
---
  .../devicetree/bindings/sound/nau8825.txt     | 111 ---------
  .../bindings/sound/nuvoton,nau8825.yaml       | 220 ++++++++++++++++++
  2 files changed, 220 insertions(+), 111 deletions(-)
  delete mode 100644 Documentation/devicetree/bindings/sound/nau8825.txt
  create mode 100644 Documentation/devicetree/bindings/sound/nuvoton,nau8825.yaml
Does not look like you tested the bindings. Please run `make
dt_binding_check` (see
Documentation/devicetree/bindings/writing-schema.rst for instructions).

No, I had ever run 'make dt_binding_check', the result is no errors.

However, regarding your bot found the warnings, I check my environment
is not the latest dtschema and without yamllint.

diff --git a/Documentation/devicetree/bindings/sound/nau8825.txt b/Documentation/devicetree/bindings/sound/nau8825.txt
deleted file mode 100644
index a9c34526f4cb..000000000000
--- a/Documentation/devicetree/bindings/sound/nau8825.txt
+++ /dev/null
@@ -1,111 +0,0 @@
-Nuvoton NAU8825 audio codec
(...)

+  nuvoton,jkdet-enable:
+    description:
+      Enable jack detection via JKDET pin.
+    type: boolean
+
+  nuvoton,jkdet-pull-enable:
+    description:
+      Enable JKDET pin pull.
+      If set - pin pull enabled, otherwise pin in high impedance state.
+    type: boolean
+
+  nuvoton,jkdet-pull-up:
+    description:
+      Pull-up JKDET pin.
+      If set then JKDET pin is pull up, otherwise pull down.
+    type: boolean
+
+  nuvoton,jkdet-polarity:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description:
+      JKDET pin polarity.
+    enum:
+      - 0 # active high
+      - 1 # active low
Since this is optional:
default: ?

Same in other places.
OK~I will add default value to these optional properties.
+
+  nuvoton,vref-impedance:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description:
+      VREF Impedance selection.
+    enum:
+      - 0 # Open
+      - 1 # 25 kOhm
+      - 2 # 125 kOhm
+      - 3 # 2.5 kOhm
+
+  nuvoton,micbias-voltage:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description:
+      Micbias voltage level.
+    enum:
+      - 0 # VDDA
+      - 1 # VDDA
+      - 2 # VDDA * 1.1
+      - 3 # VDDA * 1.2
+      - 4 # VDDA * 1.3
+      - 5 # VDDA * 1.4
+      - 6 # VDDA * 1.53
+      - 7 # VDDA * 1.53
+
+  nuvoton,sar-threshold-num:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description:
+      Number of buttons supported.
+    minimum: 1
+    maximum: 4
+
+  nuvoton,sar-threshold:
+    $ref: /schemas/types.yaml#/definitions/uint32-array
+    description:
+      Impedance threshold for each button. Array that contains up to 8 buttons
+      configuration. SAR value is calculated as
+      SAR = 255 * MICBIAS / SAR_VOLTAGE * R / (2000 + R) where MICBIAS is
+      configured by 'nuvoton,micbias-voltage', SAR_VOLTAGE is configured by
+      'nuvoton,sar-voltage', R - button impedance.
+      Refer datasheet section 10.2 for more information about threshold
+      calculation.
+    minItems: 1
+    maxItems: 4
+    items:
+      minimum: 0
+      maximum: 255
+
+  nuvoton,sar-hysteresis:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description:
+      Button impedance measurement hysteresis.
+
+  nuvoton,sar-voltage:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description:
+      Reference voltage for button impedance measurement.
+    enum:
+      - 0 # VDDA
+      - 1 # VDDA
+      - 2 # VDDA * 1.1
+      - 3 # VDDA * 1.2
+      - 4 # VDDA * 1.3
+      - 5 # VDDA * 1.4
+      - 6 # VDDA * 1.53
+      - 7 # VDDA * 1.53
+
+  nuvoton,sar-compare-time:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description:
+      SAR compare time.
+    enum:
+      - 0 # 500ns
+      - 1 # 1us
+      - 2 # 2us
+      - 3 # 4us
+
+  nuvoton,sar-sampling-time:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description:
+      SAR sampling time.
+    enum:
+      - 0 # 2us
+      - 1 # 4us
+      - 2 # 8us
+      - 3 # 16us
+
+  nuvoton,short-key-debounce:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description:
+      Button short key press debounce time.
+    enum:
+      - 0 # 30 ms
+      - 1 # 50 ms
+      - 2 # 100 ms
+
+  nuvoton,jack-insert-debounce:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description:
+      number from 0 to 7 that sets debounce time to 2^(n+2) ms.
maximum: 7

+
+  nuvoton,jack-eject-debounce:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description:
+      number from 0 to 7 that sets debounce time to 2^(n+2) ms
maximum: 7
Regarding the description have limitation for range, so your comment is
great.

+
+  nuvoton,crosstalk-enable:
+    description:
+      make crosstalk function enable if set.
+    type: boolean
+
+  nuvoton,adcout-drive-strong:
+    description:
+      make the drive strength of ADCOUT IO PIN strong if set.
+      Otherwise, the drive keeps normal strength.
+    type: boolean
+
+  nuvoton,adc-delay-ms:
+    description:
+      Delay (in ms) to make input path stable and avoid pop noise.
+      The default value is 125 and range between 125 to 500 ms.
+    minimum: 125
+    maximum: 500
+
+  clocks:
+   description:
+     list of phandle and clock specifier pairs according to common clock
+     bindings for the clocks described in clock-names.
Drop description. maxItems: 1.
OK~I will add  it.

+
+  clock-names:
+   description:
+     should include "mclk" for the MCLK master clock.
No, you need to list entries with items.
OK~I will add  it.

+
+required:
+  - compatible
+  - reg
+
+unevaluatedProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/gpio/tegra-gpio.h>
+    #include <dt-bindings/soc/tegra-pmc.h>
+    #include <dt-bindings/interrupt-controller/irq.h>
+    i2c {
+        #address-cells = <1>;
+        #size-cells = <0>;
+        headset: nau8825@1a {
Node names should be generic, audio-codec for example.
https://devicetree-specification.readthedocs.io/en/latest/chapter2-devicetree-basics.html#generic-names-recommendation
OK~I can follow it.
+            compatible = "nuvoton,nau8825";
+            reg = <0x1a>;
Best regards,
Krzysztof

________________________________
________________________________
The privileged confidential information contained in this email is intended for use only by the addressees as indicated by the original sender of this email. If you are not the addressee indicated in this email or are not responsible for delivery of the email to such a person, please kindly reply to the sender indicating this fact and delete all copies of it from your computer and network server immediately. Your cooperation is highly appreciated. It is advised that any unauthorized use of confidential information of Nuvoton is strictly prohibited; and any information in this email irrelevant to the official business of Nuvoton shall be deemed as neither given nor endorsed by Nuvoton.




[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux