On 14/04/2023 12:29, Sricharan Ramabadhran wrote:
> Add device tree binding Documentation details for ipq5018
> pinctrl driver.
>
Thank you for your patch. There is something to discuss/improve.
> +
> + interrupt-controller: true
> + "#interrupt-cells": true
> + gpio-controller: true
> + "#gpio-cells": true
> + gpio-ranges: true
> + wakeup-parent: true
> +
> + gpio-reserved-ranges:
> + minItems: 1
> + maxItems: 33
24
(you cannot have more than 24...)
> +
> + gpio-line-names:
> + maxItems: 47
> +
> +patternProperties:
> + "-state$":
> + oneOf:
> + - $ref: "#/$defs/qcom-ipq5018-tlmm-state"
> + - patternProperties:
> + "-pins$":
> + $ref: "#/$defs/qcom-ipq5018-tlmm-state"
> + additionalProperties: false
> +
> +$defs:
> + qcom-ipq5018-tlmm-state:
> + type: object
> + description:
> + Pinctrl node's client devices use subnodes for desired pin configuration.
> + Client device subnodes use below standard properties.
> + $ref: qcom,tlmm-common.yaml#/$defs/qcom-tlmm-state
> +
> + properties:
> + pins:
> + description:
> + List of gpio pins affected by the properties specified in this
> + subnode.
> + items:
> + pattern: "^gpio([0-9]|[1-3][0-9]|4[0-6])$"
> + minItems: 1
> + maxItems: 8
> +
> + function:
> + description:
> + Specify the alternative function to be configured for the specified
> + pins.
> +
> + enum: [ atest_char, audio_pdm0, audio_pdm1, audio_rxbclk, audio_rxd,
> + audio_rxfsync, audio_rxmclk, audio_txbclk, audio_txd,
> + audio_txfsync, audio_txmclk, blsp0_i2c, blsp0_spi, blsp0_uart0,
> + blsp0_uart1, blsp1_i2c0, blsp1_i2c1, blsp1_spi0, blsp1_spi1,
> + blsp1_uart0, blsp1_uart1, blsp1_uart2, blsp2_i2c0, blsp2_i2c1,
> + blsp2_spi, blsp2_spi0, blsp2_spi1, btss, burn0, burn1, cri_trng,
> + cri_trng0, cri_trng1, cxc_clk, cxc_data, dbg_out, eud_gpio,
> + gcc_plltest, gcc_tlmm, gpio, led0, led2, mac0, mac1, mdc, mdio,
> + pcie0_clk, pcie0_wake, pcie1_clk, pcie1_wake, pll_test,
> + prng_rosc, pwm0, pwm1, pwm2, pwm3, qdss_cti_trig_in_a0,
> + qdss_cti_trig_in_a1, qdss_cti_trig_in_b0, qdss_cti_trig_in_b1,
> + qdss_cti_trig_out_a0, qdss_cti_trig_out_a1,
> + qdss_cti_trig_out_b0, qdss_cti_trig_out_b1, qdss_traceclk_a,
> + qdss_traceclk_b, qdss_tracectl_a, qdss_tracectl_b,
> + qdss_tracedata_a, qdss_tracedata_b, qspi_clk, qspi_cs,
> + qspi_data, reset_out, sdc1_clk, sdc1_cmd, sdc1_data, wci_txd,
> + wci_rxd, wsa_swrm, wsi_clk3, wsi_data3, wsis_reset, xfem ]
> +
> + bias-pull-down: true
> + bias-pull-up: true
> + bias-disable: true
> + drive-strength: true
> + input-enable: true
> + output-high: true
> + output-low: true
Drop all these 7, especially that input-enable is not allowed explicitly.
> +
> + required:
> + - pins
> +
> + additionalProperties: false
Instead:
unevaluatedProperties: false
and put it after the $ref above. Just like recent changes in the next.
> +
> +required:
> + - compatible
> + - reg
> +
> +additionalProperties: false
> +
> +examples:
> + - |
> + #include <dt-bindings/interrupt-controller/arm-gic.h>
> +
> + tlmm: pinctrl@1000000 {
> + compatible = "qcom,ipq5018-tlmm";
> + reg = <0x01000000 0x300000>;
> + gpio-controller;
> + #gpio-cells = <2>;
> + gpio-ranges = <&tlmm 0 0 47>;
> + interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
> + interrupt-controller;
> + #interrupt-cells = <2>;
> +
> + uart2-state {
> + pins = "gpio34", "gpio35";
> + function = "blsp2_uart";
Does not look like you tested the bindings. Please run `make
dt_binding_check` (see
Documentation/devicetree/bindings/writing-schema.rst for instructions).
Best regards,
Krzysztof
