Re: [PATCH v1 3/3] riscv: dts: starfive: add tdm node and sound card

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On 29/03/2023 17:33, Walker Chen wrote:
> Add the tdm controller node and sound card for the StarFive JH7110 SoC.
> 
> Signed-off-by: Walker Chen <walker.chen@xxxxxxxxxxxxxxxx>
> ---
>  .../jh7110-starfive-visionfive-2.dtsi         | 87 +++++++++++++++++++
>  arch/riscv/boot/dts/starfive/jh7110.dtsi      | 34 ++++++++
>  2 files changed, 121 insertions(+)
> 
> diff --git a/arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2.dtsi b/arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2.dtsi
> index 1155b97b593d..35137c2edf5d 100644
> --- a/arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2.dtsi
> +++ b/arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2.dtsi
> @@ -62,6 +62,10 @@
>  	clock-frequency = <297000000>;
>  };
>  
> +&wm8960_mclk {
> +	clock-frequency = <24576000>;
> +};
> +
>  &i2srx_bclk_ext {
>  	clock-frequency = <12288000>;
>  };
> @@ -102,6 +106,14 @@
>  	pinctrl-names = "default";
>  	pinctrl-0 = <&i2c0_pins>;
>  	status = "okay";
> +
> +	wm8960: codec@1a {
> +		compatible = "wlf,wm8960";
> +		reg = <0x1a>;
> +		#sound-dai-cells = <0>;
> +
> +		wlf,shared-lrclk;
> +	};
>  };
>  
>  &i2c2 {
> @@ -214,6 +226,40 @@
>  			slew-rate = <0>;
>  		};
>  	};
> +
> +	tdm0_pins: tdm0-pins {
> +		tdm0-pins-tx {
> +			pinmux = <GPIOMUX(44, GPOUT_SYS_TDM_TXD,
> +					      GPOEN_ENABLE,
> +					      GPI_NONE)>;
> +			bias-pull-up;
> +			drive-strength = <2>;
> +			input-disable;
> +			input-schmitt-disable;
> +			slew-rate = <0>;
> +		};
> +
> +		tdm0-pins-rx {
> +			pinmux = <GPIOMUX(61, GPOUT_HIGH,
> +					      GPOEN_DISABLE,
> +					      GPI_SYS_TDM_RXD)>;
> +			input-enable;
> +		};
> +
> +		tdm0-pins-sync {
> +			pinmux = <GPIOMUX(63, GPOUT_HIGH,
> +					      GPOEN_DISABLE,
> +					      GPI_SYS_TDM_SYNC)>;
> +			input-enable;
> +		};
> +
> +		tdm0-pins-pcmclk {
> +			pinmux = <GPIOMUX(38, GPOUT_HIGH,
> +					      GPOEN_DISABLE,
> +					      GPI_SYS_TDM_CLK)>;
> +			input-enable;
> +		};
> +	};
>  };
>  
>  &uart0 {
> @@ -221,3 +267,44 @@
>  	pinctrl-0 = <&uart0_pins>;
>  	status = "okay";
>  };
> +
> +&tdm {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&tdm0_pins>;
> +	status = "okay";
> +};
> +
> +&sound0 {
> +	simple-audio-card,dai-link@0 {
> +		reg = <0>;
> +		status = "okay";

Why? Drop.

> +		format = "dsp_a";
> +		bitclock-master = <&dailink_master>;
> +		frame-master = <&dailink_master>;
> +
> +		widgets =

Drop line break.

> +				"Microphone", "Mic Jack",
> +				"Line", "Line In",
> +				"Line", "Line Out",
> +				"Speaker", "Speaker",
> +				"Headphone", "Headphone Jack";
> +		routing =

Drop unnecessary line break.

> +				"Headphone Jack", "HP_L",
> +				"Headphone Jack", "HP_R",
> +				"Speaker", "SPK_LP",
> +				"Speaker", "SPK_LN",
> +				"LINPUT1", "Mic Jack",
> +				"LINPUT3", "Mic Jack",
> +				"RINPUT1", "Mic Jack",
> +				"RINPUT2", "Mic Jack";
> +		cpu {
> +			sound-dai = <&tdm>;
> +		};
> +
> +		dailink_master:codec {

Missing space after label:.

> +			sound-dai = <&wm8960>;
> +			clocks = <&wm8960_mclk>;
> +			clock-names = "mclk";
> +		};
> +	};
> +};
> diff --git a/arch/riscv/boot/dts/starfive/jh7110.dtsi b/arch/riscv/boot/dts/starfive/jh7110.dtsi
> index b503b6137743..a89158d1d7a6 100644
> --- a/arch/riscv/boot/dts/starfive/jh7110.dtsi
> +++ b/arch/riscv/boot/dts/starfive/jh7110.dtsi
> @@ -210,6 +210,12 @@
>  		#clock-cells = <0>;
>  	};
>  
> +	wm8960_mclk: wm8960_mclk {

No underscores in node names. Use consistent naming - do you see here
any nodes named "mclk"?

Anyway this is some fake clock. Real clock should come out from wm8960.

> +		compatible = "fixed-clock";
> +		clock-output-names = "wm8960_mclk";
> +		#clock-cells = <0>;
> +	};
> +
>  	i2srx_bclk_ext: i2srx-bclk-ext-clock {
>  		compatible = "fixed-clock";
>  		clock-output-names = "i2srx_bclk_ext";
> @@ -375,6 +381,27 @@
>  			status = "disabled";
>  		};
>  
> +		tdm: tdm@10090000 {
> +			compatible = "starfive,jh7110-tdm";
> +			reg = <0x0 0x10090000 0x0 0x1000>;
> +			clocks = <&syscrg JH7110_SYSCLK_TDM_AHB>,
> +				 <&syscrg JH7110_SYSCLK_TDM_APB>,
> +				 <&syscrg JH7110_SYSCLK_TDM_INTERNAL>,
> +				 <&syscrg JH7110_SYSCLK_TDM_TDM>,
> +				 <&syscrg JH7110_SYSCLK_MCLK_INNER>,
> +				 <&tdm_ext>;
> +			clock-names = "tdm_ahb", "tdm_apb",
> +				      "tdm_internal", "tdm",
> +				      "mclk_inner", "tdm_ext";
> +			resets = <&syscrg JH7110_SYSRST_TDM_AHB>,
> +				 <&syscrg JH7110_SYSRST_TDM_APB>,
> +				 <&syscrg JH7110_SYSRST_TDM_CORE>;
> +			dmas = <&dma 20>, <&dma 21>;
> +			dma-names = "rx","tx";
> +			#sound-dai-cells = <0>;
> +			status = "disabled";
> +		};
> +
>  		stgcrg: clock-controller@10230000 {
>  			compatible = "starfive,jh7110-stgcrg";
>  			reg = <0x0 0x10230000 0x0 0x10000>;
> @@ -601,5 +628,12 @@
>  			#reset-cells = <1>;
>  			power-domains = <&pwrc JH7110_PD_VOUT>;
>  		};
> +
> +		sound0: snd-card0 {

1. Why card0?
2. Where is this node located? In MMIO bus? Run some basic checks on
your DTS before submitting upstream.
dtbs_check
dtbs W=1

3. Why this is even in the DTSI? This really looks wrong.

> +			compatible = "simple-audio-card";
> +			simple-audio-card,name = "Starfive-TDM-Sound-Card";
> +			#address-cells = <1>;
> +			#size-cells = <0>;

Best regards,
Krzysztof




[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux