Hi Steev,
On Sun, Mar 26, 2023 at 4:38 PM Steev Klimaszewski <steev@xxxxxxxx> wrote:
>
> The Lenovo Thinkpad X13s has a WCN6855 Bluetooth controller on uart2,
> add this.
>
> Signed-off-by: Steev Klimaszewski <steev@xxxxxxxx>
I would like to merge this set but this one still doesn't have any
Signed-off-by other than yours.
> ---
> Changes since v7:
> * Drop regulator now in a different patchset from Johan
> * Fix alphabetization
>
> Changes since v6:
> * Remove allowed-modes as they aren't needed
> * Remove regulator-allow-set-load
> * Set regulator-always-on because the wifi chip also uses the regulator
> * cts pin uses bias-bus-hold
> * Alphabetize uart2 pins
>
> Changes since v5:
> * Update patch subject
> * Specify initial mode (via guess) for vreg_s1c
> * Drop uart17 definition
> * Rename bt_en to bt_default because configuring more than one pin
> * Correct (maybe) bias configurations
> * Correct cts gpio
> * Split rts-tx into two nodes
> * Drop incorrect link in the commit message
>
> Changes since v4:
> * Address Konrad's review comments.
>
> Changes since v3:
> * Add vreg_s1c
> * Add regulators and not dead code
> * Fix commit message changelog
>
> Changes since v2:
> * Remove dead code and add TODO comment
> * Make dtbs_check happy with the pin definitions
>
> .../qcom/sc8280xp-lenovo-thinkpad-x13s.dts | 70 +++++++++++++++++++
> 1 file changed, 70 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/qcom/sc8280xp-lenovo-thinkpad-x13s.dts b/arch/arm64/boot/dts/qcom/sc8280xp-lenovo-thinkpad-x13s.dts
> index da79b5465a1b..129c5f9a2a61 100644
> --- a/arch/arm64/boot/dts/qcom/sc8280xp-lenovo-thinkpad-x13s.dts
> +++ b/arch/arm64/boot/dts/qcom/sc8280xp-lenovo-thinkpad-x13s.dts
> @@ -24,6 +24,7 @@ / {
> aliases {
> i2c4 = &i2c4;
> i2c21 = &i2c21;
> + serial1 = &uart2;
> };
>
> wcd938x: audio-codec {
> @@ -1102,6 +1103,32 @@ &txmacro {
> status = "okay";
> };
>
> +&uart2 {
> + pinctrl-0 = <&uart2_default>;
> + pinctrl-names = "default";
> +
> + status = "okay";
> +
> + bluetooth {
> + compatible = "qcom,wcn6855-bt";
> +
> + vddio-supply = <&vreg_s10b>;
> + vddbtcxmx-supply = <&vreg_s12b>;
> + vddrfacmn-supply = <&vreg_s12b>;
> + vddrfa0p8-supply = <&vreg_s12b>;
> + vddrfa1p2-supply = <&vreg_s11b>;
> + vddrfa1p7-supply = <&vreg_s1c>;
> +
> + max-speed = <3200000>;
> +
> + enable-gpios = <&tlmm 133 GPIO_ACTIVE_HIGH>;
> + swctrl-gpios = <&tlmm 132 GPIO_ACTIVE_HIGH>;
> +
> + pinctrl-0 = <&bt_default>;
> + pinctrl-names = "default";
> + };
> +};
> +
> &usb_0 {
> status = "okay";
> };
> @@ -1222,6 +1249,21 @@ hastings_reg_en: hastings-reg-en-state {
> &tlmm {
> gpio-reserved-ranges = <70 2>, <74 6>, <83 4>, <125 2>, <128 2>, <154 7>;
>
> + bt_default: bt-default-state {
> + hstp-bt-en-pins {
> + pins = "gpio133";
> + function = "gpio";
> + drive-strength = <16>;
> + bias-disable;
> + };
> +
> + hstp-sw-ctrl-pins {
> + pins = "gpio132";
> + function = "gpio";
> + bias-pull-down;
> + };
> + };
> +
> edp_reg_en: edp-reg-en-state {
> pins = "gpio25";
> function = "gpio";
> @@ -1389,6 +1431,34 @@ reset-n-pins {
> };
> };
>
> + uart2_default: uart2-default-state {
> + cts-pins {
> + pins = "gpio121";
> + function = "qup2";
> + bias-bus-hold;
> + };
> +
> + rts-pins {
> + pins = "gpio122";
> + function = "qup2";
> + drive-strength = <2>;
> + bias-disable;
> + };
> +
> + rx-pins {
> + pins = "gpio124";
> + function = "qup2";
> + bias-pull-up;
> + };
> +
> + tx-pins {
> + pins = "gpio123";
> + function = "qup2";
> + drive-strength = <2>;
> + bias-disable;
> + };
> + };
> +
> usb0_sbu_default: usb0-sbu-state {
> oe-n-pins {
> pins = "gpio101";
> --
> 2.39.2
>
--
Luiz Augusto von Dentz
