On 16:20-20230328, Roger Quadros wrote:
>
>
> On 28/03/2023 16:18, Nishanth Menon wrote:
> > On 15:43-20230328, Roger Quadros wrote:
> >> USB0 is a Type-C port with dual data role and power sink.
> >>
> >> Signed-off-by: Roger Quadros <rogerq@xxxxxxxxxx>
> >> ---
> >> arch/arm64/boot/dts/ti/k3-am62-lp-sk.dts | 4 ++
> >> arch/arm64/boot/dts/ti/k3-am625-sk.dts | 44 ++++++++++++++++++-
> >> .../arm64/boot/dts/ti/k3-am62x-sk-common.dtsi | 4 --
> >> 3 files changed, 47 insertions(+), 5 deletions(-)
> >>
> >> diff --git a/arch/arm64/boot/dts/ti/k3-am62-lp-sk.dts b/arch/arm64/boot/dts/ti/k3-am62-lp-sk.dts
> >> index b2ca19e3042e..a3c3609833fd 100644
> >> --- a/arch/arm64/boot/dts/ti/k3-am62-lp-sk.dts
> >> +++ b/arch/arm64/boot/dts/ti/k3-am62-lp-sk.dts
> >> @@ -225,3 +225,7 @@ ldo4_reg: ldo4 {
> >> };
> >> };
> >> };
> >> +
> >> +&usb0 {
> >> + dr_mode = "peripheral";
> >> +};
> >> diff --git a/arch/arm64/boot/dts/ti/k3-am625-sk.dts b/arch/arm64/boot/dts/ti/k3-am625-sk.dts
> >> index cdc0858dd1b2..13fdaa9ce4e7 100644
> >> --- a/arch/arm64/boot/dts/ti/k3-am625-sk.dts
> >> +++ b/arch/arm64/boot/dts/ti/k3-am625-sk.dts
> >> @@ -136,6 +136,35 @@ AM62X_IOPAD(0x01d4, PIN_INPUT, 7) /* (B15) UART0_RTSn.GPIO1_23 */
> >> };
> >> };
> >>
> >> +&main_i2c0 {
> >> + typec_pd: tps6598x@3f {
> >> + compatible = "ti,tps6598x";
> >> + reg = <0x3f>;
> >> + interrupt-parent = <&exp1>;
> >> + interrupts = <17 IRQ_TYPE_EDGE_FALLING>;
> >> + interrupt-names = "irq";
> >> +
> >> + connector {
> >> + compatible = "usb-c-connector";
> >> + label = "USB-C";
> >> + self-powered;
> >> + data-role = "dual";
> >> + power-role = "sink";
> >> + ports {
> >> + #address-cells = <1>;
> >> + #size-cells = <0>;
> >> +
> >> + port@0 {
> >> + reg = <0>;
> >> + usb_con_hs: endpoint {
> >> + remote-endpoint = <&usb0_hs_ep>;
> >> + };
> >> + };
> >> + };
> >> + };
> >> + };
> >> +};
> >> +
> >> &main_i2c1 {
> >> exp1: gpio@22 {
> >> compatible = "ti,tca6424";
> >> @@ -150,7 +179,7 @@ exp1: gpio@22 {
> >> "UART1_FET_BUF_EN", "WL_LT_EN",
> >> "GPIO_HDMI_RSTn", "CSI_GPIO1",
> >> "CSI_GPIO2", "PRU_3V3_EN",
> >> - "HDMI_INTn", "TEST_GPIO2",
> >> + "HDMI_INTn", "PD_I2C_IRQ",
> >> "MCASP1_FET_EN", "MCASP1_BUF_BT_EN",
> >> "MCASP1_FET_SEL", "UART1_FET_SEL",
> >> "TSINT#", "IO_EXP_TEST_LED";
> >> @@ -256,3 +285,16 @@ partition@3fc0000 {
> >> };
> >> };
> >> };
> >> +
> >> +&usb0 {
> >> + #address-cells = <1>;
> >> + #size-cells = <0>;
> >> + usb-role-switch;
> >> +
> >> + port@0 {
> >> + reg = <0>;
> >> + usb0_hs_ep: endpoint {
> >> + remote-endpoint = <&usb_con_hs>;
> >> + };
> >> + };
> >> +};
> >> diff --git a/arch/arm64/boot/dts/ti/k3-am62x-sk-common.dtsi b/arch/arm64/boot/dts/ti/k3-am62x-sk-common.dtsi
> >> index 80e8b9b9a5f5..e3223088b90c 100644
> >> --- a/arch/arm64/boot/dts/ti/k3-am62x-sk-common.dtsi
> >> +++ b/arch/arm64/boot/dts/ti/k3-am62x-sk-common.dtsi
> >> @@ -264,10 +264,6 @@ &usbss1 {
> >> ti,vbus-divider;
> >> };
> >>
> >> -&usb0 {
> >> - dr_mode = "peripheral";
> >> -};
> >> -
> >
> > How about sk-lp ?
>
> moved it to sk-lp. see above in this patch.
>
A bit confused. Looking at [1] vs [2], it seems to indicate pd controller at
0x3f as well? Am I misreading the schematics?
[1] https://www.ti.com/tool/SK-AM62-LP#design-files
[2] https://www.ti.com/tool/SK-AM62#design-files
--
Regards,
Nishanth Menon
Key (0xDDB5849D1736249D) / Fingerprint: F8A2 8693 54EB 8232 17A3 1A34 DDB5 849D 1736 249D
