Hello Hal, I start to play with jh7110-starfive-visionfive-2-v1.3b I have collect your series [3]. Now I'm trying to boot the image with the following cmds: setenv bootfile vmlinuz; setenv fileaddr a0000000; setenv fdtcontroladdr 0xffffffffffffffff; setenv ipaddr 10.0.0.100; setenv serverip 10.0.0.1; setenv kernel_comp_addr_r 0xb0000000; setenv kernel_comp_size 0x10000000; tftpboot ${fdt_addr_r} jh7110-starfive-visionfive-2-v1.3b.dtb; tftpboot ${kernel_addr_r} Image.gz; run chipa_set_linux; booti ${kernel_addr_r} - ${fdt_addr_r} This the result: Bytes transferred = 109443584 (685fa00 hex) StarFive # run chipa_set_linux; StarFive # printenv file fileaddr filesize StarFive # printenv filesize filesize=685fa00 StarFive # booti ${kernel_addr_r} - ${fdt_addr_r} Uncompressing Kernel Image ## Flattened Device Tree blob at 46000000 Booting using the fdt blob at 0x46000000 Using Device Tree in place at 0000000046000000, end 0000000046005c14 Starting kernel ... clk u5_dw_i2c_clk_core already disabled clk u5_dw_i2c_clk_apb already disabled --------------------------------------------- I'm missing something? Any hints? Many thanks in advance! :) Regards, Tommaso On Tue, Feb 21, 2023 at 10:46:26AM +0800, Hal Feng wrote: > This patch series adds basic clock, reset & DT support for StarFive > JH7110 SoC. Patch 17 depends on series [1] which provides pinctrl > dt-bindings. Patch 19 depends on series [2] which provides dt-bindings > of VisionFive 2 board and JH7110 SoC. > > You can simply review or test the patches at the link [3]. > > [1]: https://lore.kernel.org/all/20230209143702.44408-1-hal.feng@xxxxxxxxxxxxxxxx/ > [2]: https://lore.kernel.org/all/20230216131511.3327943-1-conor.dooley@xxxxxxxxxxxxx/ > [3]: https://github.com/hal-feng/linux/commits/visionfive2-minimal > > Changes since v3: > - Suggested by Conor, Merged clock & reset series and DT series together > so that they could go via the same tree as the dt-binding headers are > required by both driver & devicetree. > - Rebased on tag v6.2. > > [Clock & reset] > Patch 2: > - Split patch 2 into two. One for renaming file and one for renaming > variables. (by Conor) > Patch 4: > - Split patch 4 into two. One for code movement and one for > extraction. (by Conor) > Patch 5 & 9 & 10 & 11: > - Fixed the issues reported by kernel test robot. > Patch 9: > - Set (&priv->base) as driver data instead of (priv->base). > - Set the frequency of clock PLL0 as 1000MHz for Synchronizing with the > lastest u-boot setting from StarFive. (by Emil) > - Used devm_kzalloc() instead of kzalloc() when registering aux device. > Patch 10: > - Set (&priv->base) as driver data instead of (priv->base). > Patch 11: > - Used (*base) to get the register base address instead of (base). > > [Device tree] > - Dropped patch 1, 4, 5 because they were accepted. > - Added a new patch to add SiFive S7 compatible. (by Conor) > - Added a new patch to add JH7110 pin function definitions. > Patch 6: > - Changed the label "S76_0" to "S7_0" and used compatible "sifive,s7" > for core 0. > - Updated ISA of each cores. (by Conor) > - Made the node names generic. (by Krzysztof) > - Added clock-output-names for all external clocks. > - Added i2c0~6 nodes. > - Changed the node name "gpio" to "pinctrl". Changed the label "gpio" > and "gpioa" to "sysgpio" and "aongpio". (by Conor) > Patch 7: > - Separated the long lines into more lines in Makefile. (by Conor) > - Renamed jh7110-starfive-visionfive-2-va.dts and > jh7110-starfive-visionfive-2-vb.dts to > jh7110-starfive-visionfive-2-v1.2a.dts and > jh7110-starfive-visionfive-2-v1.3b.dts. > Changed the model and compatible to match v1.2A and v1.3B which > are printed on the silkscreen of VisionFive 2 board. (by Emil) > - Configured pins for i2c0/2/5/6 and enabled them. > > clock & reset v3: https://lore.kernel.org/all/20221220005054.34518-1-hal.feng@xxxxxxxxxxxxxxxx/ > DT v3: https://lore.kernel.org/all/20221220011247.35560-1-hal.feng@xxxxxxxxxxxxxxxx/ > > Changes since v2: > [Clock & reset] > - Rebased on tag v6.1. > - Added "JH71X0" to the StarFive driver headers in MAINTAINERS. > - Removed Co-developed-by tag of Hal in patch 1 and patch 4. > - Changed the commit author from Hal to Emil in patch 2 and patch 5. > Removed Co-developed-by tag of Emil in patch 2 and patch 5. (by Emil) > - Improved the coding style of patch 11, 12 and 13. > - Dropped patch 14. (by Emil) > Patch 4: > - Passed the "owner" member of reset_controller_dev structure > directly in reset_starfive_jh7100_register(). (by Emil) > - Added MAINTAINERS changes. > Patch 7: > - Split patch 7 into sys part and aon part. Merged them into patch 9 and > patch 10 respectively. (by Krzysztof) > - Renamed include/dt-bindings/clock/starfive-jh7110.h to > include/dt-bindings/clock/starfive,jh7110-crg.h. (by Krzysztof) > - Synchronized the definitions with the latest changes from Emil. > Patch 8: > - Split patch 8 into sys part and aon part. Merged them into patch 9 and > patch 10 respectively. (by Krzysztof) > - Renamed include/dt-bindings/reset/starfive-jh7110.h to > include/dt-bindings/reset/starfive,jh7110-crg.h. (by Krzysztof) > - Fixed the date of Copyright. (by Emil) > - Dropped weird indentations. (by Krzysztof) > - Synchronized the definitions with the latest changes from Emil. > Patch 9: > - Improved the description of clocks. (by Emil and Krzysztof) > - Added MAINTAINERS changes. > Patch 10: > - Improved the description of clocks. (by Emil and Krzysztof) > - Changed the clock-name "clk_rtc" to "rtc_osc" and "apb_bus_func" to > "apb_bus". > Patch 11: > - Removed the flags of trace/debug clocks and set the flags of core clocks > as CLK_IS_CRITICAL. (by Emil) > - Deleted the extra 1-1 clocks and synchronized the clock tree with the > latest changes from Emil. (by Emil) > - Selected RESET_STARFIVE_JH7110 in Kconfig option CLK_STARFIVE_JH7110_SYS. > Patch 12: > - Changed the macro JH7110_AONCLK_RTC to JH7110_AONCLK_RTC_OSC and > JH7110_AONCLK_APB_BUS_FUNC to JH7110_AONCLK_APB_BUS. > - Synchronized the clock tree with the latest changes from Emil. > - Set the MODULE_LICENSE as "GPL" according to commit bf7fbeeae6db. > Patch 13: > - Removed the "asserted" member in reset_info structure and always pass > NULL when calling reset_starfive_jh71x0_register(). (by Emil) > > [Device tree] > - Rebased on tag v6.1. > - Dropped patch 8 because it was merged. > Patch 1: > - Made the links into "Link:" tags. (by Conor) > - Corrected the board name to "VisionFive 2" instead of > "VisionFive V2" and added compatibles for version A and > version B of VisionFive 2. (by Emil) > Patch 4: > - Used "sifive,ccache0" compatible string to match. (by Conor) > Patch 5: > - Dropped "select SIFIVE_CCACHE" in config SOC_STARFIVE. (by Conor) > - Dropped "starfive,jh7110-ccache" compatible in > drivers/soc/sifive/sifive_ccache.c. > Patch 6: > - Removed all "clock-frequency = <0>". (by Conor) > - Sorted the nodes after their addresses. (by Emil) > - Renamed "clk_rtc" to "rtc_osc". > - Added "sifive,ccache0" compatible in the cache-controller node. > - Renamed "JH7110_SYSCLK_APB_BUS_FUNC" to "JH7110_SYSCLK_APB_BUS" and > renamed "apb_bus_func" to "apb_bus". > Renamed "JH7110_SYSCLK_IOMUX" to "JH7110_SYSCLK_IOMUX_APB". > Renamed "JH7110_SYSRST_IOMUX" to "JH7110_SYSRST_IOMUX_APB". > Renamed "JH7110_AONRST_AON_IOMUX" to "JH7110_AONRST_IOMUX". > - Removed "reg-names" in gpio nodes. > Patch 7: > - Corrected the board name to "VisionFive 2" instead of "VisionFive V2". > - Renamed jh7110-starfive-visionfive-v2.dts to > jh7110-starfive-visionfive-2.dtsi. > - Added dts for VisionFive 2 version A and version B boards. > - In the chosen node, deleted "linux,initrd-start" and "linux,initrd-end" > and changed the value of "stdout-path" to "serial0:115200n8". > - Changed the bias of uart0 "rx-pins" to > "bias-disable; /* external pull-up */". > - Renamed "clk_rtc" to "rtc_osc". > - Moved the gpio node behind the uart0 node. > > clock & reset v2: https://lore.kernel.org/all/20221118010627.70576-1-hal.feng@xxxxxxxxxxxxxxxx/ > DT v2: https://lore.kernel.org/all/20221118011714.70877-1-hal.feng@xxxxxxxxxxxxxxxx/ > > Changes since v1: > [Clock & reset] > - Rebased on tag v6.1-rc5. > - Rewrote the clock and reset drivers using auxiliary bus framework, so > patch 8, 9, 15 were dropped and all patches changed a lot. (by Stephen) > - Split Patch 14 into two patches. One is for factoring out the common > JH71X0 code, the another one is for renaming. (by Stephen) > - Created a subdirectory for StarFive reset drivers. > - Factored out common JH71X0 reset code. > - Renamed the common clock and reset code from "*starfive*" or > "*STARFIVE*" to "*jh71x0*" or "*JH71X0*". > - Combined JH7110 system and always-on clock DT binding headers in one > file named "include/dt-bindings/clock/starfive-jh7110.h". > - Renamed clock definitions "JH7110_SYSCLK_PCLK2_MUX_FUNC_PCLK" and > "JH7110_SYSCLK_U2_PCLK_MUX_PCLK" to "JH7110_SYSCLK_PCLK2_MUX_FUNC" and > "JH7110_SYSCLK_PCLK2_MUX". > - Rewrote the DT bindings of clock and reset for using auxiliary bus. > - Registered an auxiliary device for reset controller in clock drivers. > - Changed clock names "CODAJ*" and "WAVE*" to "codaj*" and "wave*". > Changed clock names "u2_pclk_mux_func_pclk" and "u2_pclk_mux_pclk" to > "pclk2_mux_func" and "pclk2_mux". > - Changed the flags of clock apb0 and noc_bus_isp_axi to CLK_IS_CRITICAL > as suggested by StarFive SDK group. > - Registered clock gmac0_gtxc as a gate clock instead of a div clock > as suggested by StarFive SDK group. > - Changed the frequency of clock pll2_out to 1188MHz as suggested by > StarFive SDK group. > - Fixed the bug that the clock JH7110_AONCLK_GMAC0_GTXCLK was not handled > in JH7110 always-on clock driver. > - Registered the reset driver as an auxiliary driver. > - Reworded the commit messages. > > [Device tree] > - Rebased on tag v6.1-rc5. > - Added blank line in patch 1. (by Krzysztof) > - Rebased patch 4 and 6 on the newest code. (by Conor) > - Dropped patch 5. (by Conor) > - Removed the quirk of JH7100 in patch 6, considering this patch series > should only add support for JH7110. > - For patch 27, added Co-developed-by tag for Jianlong and me. Renamed > cpu labels to "S76_0", "U74_*" instead of "cpu*" following the style > of jh7100.dtsi. Moved all "clock-frequency" properties to the board dts. > Rewrote clock-controller nodes and deleted reset-controller nodes for > using auxiliary bus. Rewrote gpio nodes following generic pinctrl > bindings. Removed the redundant second reset entry of uart nodes. > - For patch 28, added Co-developed-by tag for Jianlong and me. Added a > chosen node. Removed reserved-memory node. Added fixed frequency clock > nodes for overriding the "clock-frequency" properties. Rewrote the gpio > nodes following generic pinctrl bindings. > - Dropped patch 30. (by Conor) > - Reworded the commit messages. > > v1: https://lore.kernel.org/all/20220929143225.17907-1-hal.feng@xxxxxxxxxxxxxxxxxxxxxx/ > > Emil Renner Berthing (16): > clk: starfive: Factor out common JH7100 and JH7110 code > clk: starfive: Rename clk-starfive-jh7100.h to clk-starfive-jh71x0.h > clk: starfive: Rename "jh7100" to "jh71x0" for the common code > reset: Create subdirectory for StarFive drivers > reset: starfive: Factor out common JH71X0 reset code > reset: starfive: Extract the common JH71X0 reset code > reset: starfive: Rename "jh7100" to "jh71x0" for the common code > reset: starfive: jh71x0: Use 32bit I/O on 32bit registers > dt-bindings: clock: Add StarFive JH7110 system clock and reset > generator > dt-bindings: clock: Add StarFive JH7110 always-on clock and reset > generator > clk: starfive: Add StarFive JH7110 system clock driver > clk: starfive: Add StarFive JH7110 always-on clock driver > dt-bindings: timer: Add StarFive JH7110 clint > dt-bindings: interrupt-controller: Add StarFive JH7110 plic > riscv: dts: starfive: Add initial StarFive JH7110 device tree > riscv: dts: starfive: Add StarFive JH7110 VisionFive 2 board device > tree > > Hal Feng (2): > reset: starfive: Add StarFive JH7110 reset driver > dt-bindings: riscv: Add SiFive S7 compatible > > Jianlong Huang (1): > riscv: dts: starfive: Add StarFive JH7110 pin function definitions > > .../clock/starfive,jh7110-aoncrg.yaml | 76 ++ > .../clock/starfive,jh7110-syscrg.yaml | 80 ++ > .../sifive,plic-1.0.0.yaml | 1 + > .../devicetree/bindings/riscv/cpus.yaml | 1 + > .../bindings/timer/sifive,clint.yaml | 1 + > MAINTAINERS | 16 +- > arch/riscv/boot/dts/starfive/Makefile | 6 +- > arch/riscv/boot/dts/starfive/jh7110-pinfunc.h | 308 ++++++++ > .../jh7110-starfive-visionfive-2-v1.2a.dts | 13 + > .../jh7110-starfive-visionfive-2-v1.3b.dts | 13 + > .../jh7110-starfive-visionfive-2.dtsi | 215 ++++++ > arch/riscv/boot/dts/starfive/jh7110.dtsi | 507 +++++++++++++ > drivers/clk/starfive/Kconfig | 27 + > drivers/clk/starfive/Makefile | 6 +- > .../clk/starfive/clk-starfive-jh7100-audio.c | 74 +- > drivers/clk/starfive/clk-starfive-jh7100.c | 713 +++++------------- > drivers/clk/starfive/clk-starfive-jh7100.h | 112 --- > .../clk/starfive/clk-starfive-jh7110-aon.c | 156 ++++ > .../clk/starfive/clk-starfive-jh7110-sys.c | 448 +++++++++++ > drivers/clk/starfive/clk-starfive-jh71x0.c | 383 ++++++++++ > drivers/clk/starfive/clk-starfive-jh71x0.h | 122 +++ > drivers/reset/Kconfig | 8 +- > drivers/reset/Makefile | 2 +- > drivers/reset/reset-starfive-jh7100.c | 173 ----- > drivers/reset/starfive/Kconfig | 20 + > drivers/reset/starfive/Makefile | 5 + > .../reset/starfive/reset-starfive-jh7100.c | 74 ++ > .../reset/starfive/reset-starfive-jh7110.c | 64 ++ > .../reset/starfive/reset-starfive-jh71x0.c | 131 ++++ > .../reset/starfive/reset-starfive-jh71x0.h | 20 + > .../dt-bindings/clock/starfive,jh7110-crg.h | 225 ++++++ > .../dt-bindings/reset/starfive,jh7110-crg.h | 154 ++++ > 32 files changed, 3296 insertions(+), 858 deletions(-) > create mode 100644 Documentation/devicetree/bindings/clock/starfive,jh7110-aoncrg.yaml > create mode 100644 Documentation/devicetree/bindings/clock/starfive,jh7110-syscrg.yaml > create mode 100644 arch/riscv/boot/dts/starfive/jh7110-pinfunc.h > create mode 100644 arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2-v1.2a.dts > create mode 100644 arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2-v1.3b.dts > create mode 100644 arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2.dtsi > create mode 100644 arch/riscv/boot/dts/starfive/jh7110.dtsi > delete mode 100644 drivers/clk/starfive/clk-starfive-jh7100.h > create mode 100644 drivers/clk/starfive/clk-starfive-jh7110-aon.c > create mode 100644 drivers/clk/starfive/clk-starfive-jh7110-sys.c > create mode 100644 drivers/clk/starfive/clk-starfive-jh71x0.c > create mode 100644 drivers/clk/starfive/clk-starfive-jh71x0.h > delete mode 100644 drivers/reset/reset-starfive-jh7100.c > create mode 100644 drivers/reset/starfive/Kconfig > create mode 100644 drivers/reset/starfive/Makefile > create mode 100644 drivers/reset/starfive/reset-starfive-jh7100.c > create mode 100644 drivers/reset/starfive/reset-starfive-jh7110.c > create mode 100644 drivers/reset/starfive/reset-starfive-jh71x0.c > create mode 100644 drivers/reset/starfive/reset-starfive-jh71x0.h > create mode 100644 include/dt-bindings/clock/starfive,jh7110-crg.h > create mode 100644 include/dt-bindings/reset/starfive,jh7110-crg.h > > > base-commit: c9c3395d5e3dcc6daee66c6908354d47bf98cb0c > -- > 2.38.1 >