On Tue, 28 Feb 2023 at 09:16, Jeremy Kerr <jk@xxxxxxxxxxxxxxxxxxxx> wrote:
>
> The current ast2600 I3C clock definitions are top-level (rather than
> based on their actual hw sources: either HCLK or APLL), and include a
> couple of definitions for (non-existent) i3c6 and i3c7.
>
> Re-parent the individual I3C controller clocks to the main i3c clock,
> explicitly sourced from the APLL rather than whatever G6_CLK_SELECTION5
> was last set to.
>
> While we're at it, remove the definitions for the i3c6 and i3c7 clock
> lines; this hardware isn't present.
>
> This is a partial cherry-pick and rework of ed44b8cdfdb and 1a35eb926d7
> from Aspeed's own tree, originally by Dylan Hung
> <dylan_hung@xxxxxxxxxxxxxx>.
>
> Signed-off-by: Jeremy Kerr <jk@xxxxxxxxxxxxxxxxxxxx>
Looks good. I have some suggestions below.
>
> ---
> v4:
> - expand NUM_CLKS for the new I3C clock
> v3:
> - split dt-bindings and clk changes
> v2:
> - reword commit message
> ---
> drivers/clk/clk-ast2600.c | 40 ++++++++++++++++++++++++++++++---------
> 1 file changed, 31 insertions(+), 9 deletions(-)
>
> diff --git a/drivers/clk/clk-ast2600.c b/drivers/clk/clk-ast2600.c
> index 1f08ff3c60fa..d465d097e6f2 100644
> --- a/drivers/clk/clk-ast2600.c
> +++ b/drivers/clk/clk-ast2600.c
> @@ -4,6 +4,7 @@
>
> #define pr_fmt(fmt) "clk-ast2600: " fmt
>
> +#include <linux/bitfield.h>
> #include <linux/mfd/syscon.h>
> #include <linux/of_address.h>
> #include <linux/of_device.h>
> @@ -15,7 +16,7 @@
>
> #include "clk-aspeed.h"
>
> -#define ASPEED_G6_NUM_CLKS 71
> +#define ASPEED_G6_NUM_CLKS 72
NUM_CLKS seems dangerous. Should we instead use ARRAY_SIZE(aspeed_g6_gates)?
Or at least a BUILD_BUG_ON( ARRAY_SIZE(aspeed_g6_gates) != ASPEED_G6_NUM_CLKS))?
>
> #define ASPEED_G6_SILICON_REV 0x014
> #define CHIP_REVISION_ID GENMASK(23, 16)
> @@ -32,6 +33,18 @@
> #define ASPEED_G6_CLK_SELECTION1 0x300
> #define ASPEED_G6_CLK_SELECTION2 0x304
> #define ASPEED_G6_CLK_SELECTION4 0x310
> +#define ASPEED_G6_CLK_SELECTION5 0x314
> +#define I3C_CLK_SELECTION BIT(31)
> +#define I3C_CLK_SELECT_HCLK 0
> +#define I3C_CLK_SELECT_APLL_DIV 1
> +#define APLL_DIV_SELECTION GENMASK(30, 28)
> +#define APLL_DIV_2 0b001
> +#define APLL_DIV_3 0b010
> +#define APLL_DIV_4 0b011
> +#define APLL_DIV_5 0b100
> +#define APLL_DIV_6 0b101
> +#define APLL_DIV_7 0b110
> +#define APLL_DIV_8 0b111
>
> #define ASPEED_HPLL_PARAM 0x200
> #define ASPEED_APLL_PARAM 0x210
> @@ -97,14 +110,13 @@ static const struct aspeed_gate_data aspeed_g6_gates[] = {
> [ASPEED_CLK_GATE_LHCCLK] = { 37, -1, "lhclk-gate", "lhclk", 0 }, /* LPC master/LPC+ */
> /* Reserved 38 RSA: no longer used */
> /* Reserved 39 */
> - [ASPEED_CLK_GATE_I3C0CLK] = { 40, 40, "i3c0clk-gate", NULL, 0 }, /* I3C0 */
> - [ASPEED_CLK_GATE_I3C1CLK] = { 41, 41, "i3c1clk-gate", NULL, 0 }, /* I3C1 */
> - [ASPEED_CLK_GATE_I3C2CLK] = { 42, 42, "i3c2clk-gate", NULL, 0 }, /* I3C2 */
> - [ASPEED_CLK_GATE_I3C3CLK] = { 43, 43, "i3c3clk-gate", NULL, 0 }, /* I3C3 */
> - [ASPEED_CLK_GATE_I3C4CLK] = { 44, 44, "i3c4clk-gate", NULL, 0 }, /* I3C4 */
> - [ASPEED_CLK_GATE_I3C5CLK] = { 45, 45, "i3c5clk-gate", NULL, 0 }, /* I3C5 */
> - [ASPEED_CLK_GATE_I3C6CLK] = { 46, 46, "i3c6clk-gate", NULL, 0 }, /* I3C6 */
> - [ASPEED_CLK_GATE_I3C7CLK] = { 47, 47, "i3c7clk-gate", NULL, 0 }, /* I3C7 */
> + [ASPEED_CLK_GATE_I3C0CLK] = { 40, 40, "i3c0clk-gate", "i3cclk", 0 }, /* I3C0 */
> + [ASPEED_CLK_GATE_I3C1CLK] = { 41, 41, "i3c1clk-gate", "i3cclk", 0 }, /* I3C1 */
> + [ASPEED_CLK_GATE_I3C2CLK] = { 42, 42, "i3c2clk-gate", "i3cclk", 0 }, /* I3C2 */
> + [ASPEED_CLK_GATE_I3C3CLK] = { 43, 43, "i3c3clk-gate", "i3cclk", 0 }, /* I3C3 */
> + [ASPEED_CLK_GATE_I3C4CLK] = { 44, 44, "i3c4clk-gate", "i3cclk", 0 }, /* I3C4 */
> + [ASPEED_CLK_GATE_I3C5CLK] = { 45, 45, "i3c5clk-gate", "i3cclk", 0 }, /* I3C5 */
> + /* Reserved: 46 & 47 */
> [ASPEED_CLK_GATE_UART1CLK] = { 48, -1, "uart1clk-gate", "uart", 0 }, /* UART1 */
> [ASPEED_CLK_GATE_UART2CLK] = { 49, -1, "uart2clk-gate", "uart", 0 }, /* UART2 */
> [ASPEED_CLK_GATE_UART3CLK] = { 50, -1, "uart3clk-gate", "uart", 0 }, /* UART3 */
> @@ -775,6 +787,16 @@ static void __init aspeed_g6_cc(struct regmap *map)
> /* USB 2.0 port1 phy 40MHz clock */
> hw = clk_hw_register_fixed_rate(NULL, "usb-phy-40m", NULL, 0, 40000000);
> aspeed_g6_clk_data->hws[ASPEED_CLK_USBPHY_40M] = hw;
> +
> + /* i3c clock: source from apll, divide by 8 */
> + regmap_read(map, ASPEED_G6_CLK_SELECTION5, &val);
> + val &= ~(I3C_CLK_SELECTION | APLL_DIV_SELECTION);
Is there any value in registering a mux device here? See the emmc extclk device.
> + val |= FIELD_PREP(I3C_CLK_SELECTION, I3C_CLK_SELECT_APLL_DIV);
> + val |= FIELD_PREP(APLL_DIV_SELECTION, APLL_DIV_8);
> + regmap_write(map, ASPEED_G6_CLK_SELECTION5, val);
This is a departure in style from the existing code. The existing code
did things like this:
regmap_update_bits(map, ASPEED_G6_CLK_SELECTION1, GENMASK(10,
8), BIT(10));
Which uses the regmap API instead of FIELD_PREP macros. If you think
FIELD_PREP is better then that's fine.
> +
> + hw = clk_hw_register_fixed_factor(NULL, "i3cclk", "apll", 0, 1, 8);
> + aspeed_g6_clk_data->hws[ASPEED_CLK_I3C] = hw;
> };
>
> static void __init aspeed_g6_cc_init(struct device_node *np)
> --
> 2.39.1
>
