From: Aswath Govindraju <a-govindraju@xxxxxx>
Add PCIe1 RC device tree node for the single PCIe instance present on
the j721s2.
Reviewed-by: Siddharth Vadapalli <s-vadapalli@xxxxxx>
Signed-off-by: Aswath Govindraju <a-govindraju@xxxxxx>
Signed-off-by: Vignesh Raghavendra <vigneshr@xxxxxx>
Signed-off-by: Matt Ranostay <mranostay@xxxxxx>
Signed-off-by: Ravi Gunasekaran <r-gunasekaran@xxxxxx>
---
Changes from v10:
* Removed Link tag from commit message
Changes from v9:
* No change
Changes from v8:
* No change
Changes from v7:
* No change
Changes from v6:
* Remove the pcie_ep node as device cannot act as RC and EP
at the same time
Changes from v5:
* No change
Changes from v4:
* No change
Changes from v3:
* No change
Changes from v2:
* Patch newly added to the series
arch/arm64/boot/dts/ti/k3-j721s2-main.dtsi | 47 ++++++++++++++++++++++
1 file changed, 47 insertions(+)
diff --git a/arch/arm64/boot/dts/ti/k3-j721s2-main.dtsi b/arch/arm64/boot/dts/ti/k3-j721s2-main.dtsi
index c9b90ffb4f7c..35aae4b52c54 100644
--- a/arch/arm64/boot/dts/ti/k3-j721s2-main.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j721s2-main.dtsi
@@ -871,6 +871,53 @@
};
};
+ pcie1_rc: pcie@2910000 {
+ compatible = "ti,j7200-pcie-host", "ti,j721e-pcie-host";
+ reg = <0x00 0x02910000 0x00 0x1000>,
+ <0x00 0x02917000 0x00 0x400>,
+ <0x00 0x0d800000 0x00 0x00800000>,
+ <0x00 0x18000000 0x00 0x00001000>;
+ reg-names = "intd_cfg", "user_cfg", "reg", "cfg";
+ interrupt-names = "link_state";
+ interrupts = <GIC_SPI 330 IRQ_TYPE_EDGE_RISING>;
+ device_type = "pci";
+ ti,syscon-pcie-ctrl = <&scm_conf 0x074>;
+ max-link-speed = <3>;
+ num-lanes = <4>;
+ power-domains = <&k3_pds 276 TI_SCI_PD_EXCLUSIVE>;
+ clocks = <&k3_clks 276 41>;
+ clock-names = "fck";
+ #address-cells = <3>;
+ #size-cells = <2>;
+ bus-range = <0x0 0xff>;
+ vendor-id = <0x104c>;
+ device-id = <0xb013>;
+ msi-map = <0x0 &gic_its 0x0 0x10000>;
+ dma-coherent;
+ ranges = <0x01000000 0x0 0x18001000 0x00 0x18001000 0x0 0x0010000>,
+ <0x02000000 0x0 0x18011000 0x00 0x18011000 0x0 0x7fef000>;
+ dma-ranges = <0x02000000 0x0 0x0 0x0 0x0 0x10000 0x0>;
+ #interrupt-cells = <1>;
+ interrupt-map-mask = <0 0 0 7>;
+ interrupt-map = <0 0 0 1 &pcie1_intc 0>, /* INT A */
+ <0 0 0 2 &pcie1_intc 0>, /* INT B */
+ <0 0 0 3 &pcie1_intc 0>, /* INT C */
+ <0 0 0 4 &pcie1_intc 0>; /* INT D */
+ /*
+ * Disable the node by default in the common include file.
+ * And enable it in the board specific DT file where the
+ * pinmux property is added.
+ */
+ status = "disabled";
+
+ pcie1_intc: interrupt-controller {
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ interrupt-parent = <&gic500>;
+ interrupts = <GIC_SPI 324 IRQ_TYPE_EDGE_RISING>;
+ };
+ };
+
main_mcan0: can@2701000 {
compatible = "bosch,m_can";
reg = <0x00 0x02701000 0x00 0x200>,
--
2.17.1
