This is another attempt on adding this feature on LEDs, hoping this is the right time and someone finally notice this. Most of the times Switch/PHY have connected multiple LEDs that are controlled by HW based on some rules/event. Currently we lack any support for a generic way to control the HW part and normally we either never implement the feature or only add control for brightness or hw blink. This is based on Marek idea of providing some API to cled but use a different implementation that in theory should be more generilized. The current idea is: - LED driver implement 3 API (hw_control_status/start/stop). They are used to put the LED in hardware mode and to configure the various trigger. - We have hardware triggers that are used to expose to userspace the supported hardware mode and set the hardware mode on trigger activation. - We can also have triggers that both support hardware and software mode. - The LED driver will declare each supported hardware blink mode and communicate with the trigger all the supported blink modes that will be available by sysfs. - A trigger will use blink_set to configure the blink mode to active in hardware mode. - On hardware trigger activation, only the hardware mode is enabled but the blink modes are not configured. The LED driver should reset any link mode active by default. Each LED driver will have to declare explicit support for the offload trigger (or return not supported error code) as we the trigger_data that the LED driver will elaborate and understand what is referring to (based on the current active trigger). I posted a user for this new implementation that will benefit from this and will add a big feature to it. Currently qca8k can have up to 3 LEDs connected to each PHY port and we have some device that have only one of them connected and the default configuration won't work for that. The netdev trigger is expanded and it does now support hardware only triggers. The idea is to use hardware mode when a device_name is not defined. An additional sysfs entry is added to give some info about the available trigger modes supported in the current configuration. It was reported that at least 3 other switch family would benefits by this as they all lack support for a generic way to setup their leds and netdev team NACK each try to add special code to support LEDs present on switch in favor of a generic solution. v8: - Improve the documentation of the new feature - Rename to a more symbolic name - Fix some bug in netdev trigger (not using BIT()) - Add more define for qca8k-leds driver - Add activity led mode - Drop interval support - Move qca8k brightness set to blocking variant (can sleep while setting the mode) - More some function out of config define and provide variant if not selected - Fix many bugs in the validate option in the netdev trigger - Add phy generic schema for leds support - Add additional required Documentation changes v7: - Rebase on top of net-next (for qca8k changes) - Fix some typo in commit description - Fix qca8k leds documentation warning - Remove RFC tag v6: - Back to RFC. - Drop additional trigger - Rework netdev trigger to support common modes used by switch and hardware only triggers - Refresh qca8k leds logic and driver v5: - Move out of RFC. (no comments from Andrew this is the right path?) - Fix more spelling mistake (thx Randy) - Fix error reported by kernel test bot - Drop the additional HW_CONTROL flag. It does simplify CONFIG handling and hw control should be available anyway to support triggers as module. v4: - Rework implementation and drop hw_configure logic. We now expand blink_set. - Address even more spelling mistake. (thx a lot Randy) - Drop blink option and use blink_set delay. - Rework phy-activity trigger to actually make the groups dynamic. v3: - Rework start/stop as Andrew asked. - Introduce more logic to permit a trigger to run in hardware mode. - Add additional patch with netdev hardware support. - Use test_bit API to check flag passed to hw_control_configure. - Added a new cmd to hw_control_configure to reset any active blink_mode. - Refactor all the patches to follow this new implementation. v2: - Fix spelling mistake (sorry) - Drop patch 02 "permit to declare supported offload triggers". Change the logic, now the LED driver declare support for them using the configure_offload with the cmd TRIGGER_SUPPORTED. - Rework code to follow this new implementation. - Update Documentation to better describe how this offload implementation work. Christian Marangi (13): leds: add support for hardware driven LEDs leds: add function to configure hardware controlled LED leds: trigger: netdev: drop NETDEV_LED_MODE_LINKUP from mode leds: trigger: netdev: rename and expose NETDEV trigger enum modes leds: trigger: netdev: convert device attr to macro leds: trigger: netdev: add hardware control support leds: trigger: netdev: use mutex instead of spinlocks leds: trigger: netdev: add available mode sysfs attr leds: trigger: netdev: add additional hardware only triggers net: dsa: qca8k: add LEDs support dt-bindings: leds: Document netdev trigger dt-bindings: net: phy: Document support for leds node dt-bindings: net: dsa: qca8k: add LEDs definition example .../devicetree/bindings/leds/common.yaml | 2 + .../devicetree/bindings/net/dsa/qca8k.yaml | 24 + .../devicetree/bindings/net/ethernet-phy.yaml | 22 + Documentation/leds/leds-class.rst | 94 ++++ drivers/leds/Kconfig | 11 + drivers/leds/led-class.c | 27 ++ drivers/leds/led-triggers.c | 38 ++ drivers/leds/trigger/ledtrig-netdev.c | 414 ++++++++++++----- drivers/net/dsa/qca/Kconfig | 9 + drivers/net/dsa/qca/Makefile | 1 + drivers/net/dsa/qca/qca8k-8xxx.c | 4 + drivers/net/dsa/qca/qca8k-leds.c | 419 ++++++++++++++++++ drivers/net/dsa/qca/qca8k.h | 69 +++ include/linux/leds.h | 95 +++- 14 files changed, 1126 insertions(+), 103 deletions(-) create mode 100644 drivers/net/dsa/qca/qca8k-leds.c -- 2.38.1
