Re: [PATCH v1 2/4] hwmon: (sfctemp) Add StarFive JH71x0 temperature sensor

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On 2/6/23 09:12, Hal Feng wrote:
On Tue, 3 Jan 2023 14:10:17 -0800, Guenter Roeck wrote:
On Tue, Jan 03, 2023 at 09:31:43AM +0800, Hal Feng wrote:
From: Emil Renner Berthing <kernel@xxxxxxxx>

Register definitions and conversion constants based on sfctemp driver by
Samin in the StarFive 5.10 kernel.

Signed-off-by: Emil Renner Berthing <kernel@xxxxxxxx>
Co-developed-by: Samin Guo <samin.guo@xxxxxxxxxxxxxxxx>
Signed-off-by: Samin Guo <samin.guo@xxxxxxxxxxxxxxxx>
Signed-off-by: Hal Feng <hal.feng@xxxxxxxxxxxxxxxx>

This is obviously version 4 of the previous patch series,
with various enhancements. Please do not "sell" that as
v1 of a new patch series. Submit it as next version,
and provide a change log.

Sorry to reply too late. I will resend this series as v4 tomorrow.


---
  Documentation/hwmon/index.rst   |   1 +
  Documentation/hwmon/sfctemp.rst |  33 +++
  MAINTAINERS                     |   8 +
  drivers/hwmon/Kconfig           |  10 +
  drivers/hwmon/Makefile          |   1 +
  drivers/hwmon/sfctemp.c         | 350 ++++++++++++++++++++++++++++++++
  6 files changed, 403 insertions(+)
  create mode 100644 Documentation/hwmon/sfctemp.rst
  create mode 100644 drivers/hwmon/sfctemp.c

diff --git a/Documentation/hwmon/index.rst b/Documentation/hwmon/index.rst
index c1d11cf13eef..f7ede608b6e3 100644
--- a/Documentation/hwmon/index.rst
+++ b/Documentation/hwmon/index.rst
@@ -179,6 +179,7 @@ Hardware Monitoring Kernel Drivers
     sch5627
     sch5636
     scpi-hwmon
+   sfctemp
     sht15
     sht21
     sht3x
diff --git a/Documentation/hwmon/sfctemp.rst b/Documentation/hwmon/sfctemp.rst
new file mode 100644
index 000000000000..9fbd5bb1f356
--- /dev/null
+++ b/Documentation/hwmon/sfctemp.rst
@@ -0,0 +1,33 @@
+.. SPDX-License-Identifier: GPL-2.0
+
+Kernel driver sfctemp
+=====================
+
+Supported chips:
+ - StarFive JH7100
+ - StarFive JH7110
+
+Authors:
+ - Emil Renner Berthing <kernel@xxxxxxxx>
+
+Description
+-----------
+
+This driver adds support for reading the built-in temperature sensor on the
+JH7100 and JH7110 RISC-V SoCs by StarFive Technology Co. Ltd.
+
+``sysfs`` interface
+-------------------
+
+The temperature sensor can be enabled, disabled and queried via the standard
+hwmon interface in sysfs under ``/sys/class/hwmon/hwmonX`` for some value of
+``X``:
+
+================ ==== =============================================
+Name             Perm Description
+================ ==== =============================================
+temp1_enable     RW   Enable or disable temperature sensor.
+                      Automatically enabled by the driver,
+                      but may be disabled to save power.
+temp1_input      RO   Temperature reading in milli-degrees Celsius.
+================ ==== =============================================
diff --git a/MAINTAINERS b/MAINTAINERS
index 85e8f83161d7..ab3cd5827b26 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -18661,6 +18661,14 @@ L:	netdev@xxxxxxxxxxxxxxx
  S:	Supported
  F:	drivers/net/ethernet/sfc/
+SFCTEMP HWMON DRIVER
+M:	Emil Renner Berthing <kernel@xxxxxxxx>
+L:	linux-hwmon@xxxxxxxxxxxxxxx
+S:	Maintained
+F:	Documentation/devicetree/bindings/hwmon/starfive,jh71x0-temp.yaml
+F:	Documentation/hwmon/sfctemp.rst
+F:	drivers/hwmon/sfctemp.c
+
  SFF/SFP/SFP+ MODULE SUPPORT
  M:	Russell King <linux@xxxxxxxxxxxxxxx>
  L:	netdev@xxxxxxxxxxxxxxx
diff --git a/drivers/hwmon/Kconfig b/drivers/hwmon/Kconfig
index 7ac3daaf59ce..c6bbfcca3a14 100644
--- a/drivers/hwmon/Kconfig
+++ b/drivers/hwmon/Kconfig
@@ -1910,6 +1910,16 @@ config SENSORS_STTS751
  	  This driver can also be built as a module. If so, the module
  	  will be called stts751.
+config SENSORS_SFCTEMP
+	tristate "Starfive JH71x0 temperature sensor"
+	depends on SOC_STARFIVE || COMPILE_TEST
+	help
+	  If you say yes here you get support for temperature sensor
+	  on the Starfive JH71x0 SoCs.
+
+	  This driver can also be built as a module.  If so, the module
+	  will be called sfctemp.
+
  config SENSORS_SMM665
  	tristate "Summit Microelectronics SMM665"
  	depends on I2C
diff --git a/drivers/hwmon/Makefile b/drivers/hwmon/Makefile
index 11d076cad8a2..5a4a02c5535c 100644
--- a/drivers/hwmon/Makefile
+++ b/drivers/hwmon/Makefile
@@ -179,6 +179,7 @@ obj-$(CONFIG_SENSORS_SBRMI)	+= sbrmi.o
  obj-$(CONFIG_SENSORS_SCH56XX_COMMON)+= sch56xx-common.o
  obj-$(CONFIG_SENSORS_SCH5627)	+= sch5627.o
  obj-$(CONFIG_SENSORS_SCH5636)	+= sch5636.o
+obj-$(CONFIG_SENSORS_SFCTEMP)	+= sfctemp.o
  obj-$(CONFIG_SENSORS_SL28CPLD)	+= sl28cpld-hwmon.o
  obj-$(CONFIG_SENSORS_SHT15)	+= sht15.o
  obj-$(CONFIG_SENSORS_SHT21)	+= sht21.o
diff --git a/drivers/hwmon/sfctemp.c b/drivers/hwmon/sfctemp.c
new file mode 100644
index 000000000000..e56716ad9587
--- /dev/null
+++ b/drivers/hwmon/sfctemp.c
@@ -0,0 +1,350 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2021 Emil Renner Berthing <kernel@xxxxxxxx>
+ * Copyright (C) 2021 Samin Guo <samin.guo@xxxxxxxxxxxxxxxx>
+ */
+#include <linux/clk.h>
+#include <linux/completion.h>
+#include <linux/delay.h>
+#include <linux/hwmon.h>
+#include <linux/interrupt.h>
+#include <linux/io.h>
+#include <linux/module.h>
+#include <linux/mutex.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+#include <linux/reset.h>
+
+/*
+ * TempSensor reset. The RSTN can be de-asserted once the analog core has
+ * powered up. Trst(min 100ns)
+ * 0:reset  1:de-assert
+ */
+#define SFCTEMP_RSTN	BIT(0)

Missing include of linux/bits.h

Will add it. Thanks.


+
+/*
+ * TempSensor analog core power down. The analog core will be powered up
+ * Tpu(min 50us) after PD is de-asserted. RSTN should be held low until the
+ * analog core is powered up.
+ * 0:power up  1:power down
+ */
+#define SFCTEMP_PD	BIT(1)
+
+/*
+ * TempSensor start conversion enable.
+ * 0:disable  1:enable
+ */
+#define SFCTEMP_RUN	BIT(2)
+
+/*
+ * TempSensor conversion value output.
+ * Temp(C)=DOUT*Y/4094 - K
+ */
+#define SFCTEMP_DOUT_POS	16
+#define SFCTEMP_DOUT_MSK	GENMASK(27, 16)
+
+/* DOUT to Celcius conversion constants */
+#define SFCTEMP_Y1000	237500L
+#define SFCTEMP_Z	4094L
+#define SFCTEMP_K1000	81100L
+
+struct sfctemp {
+	/* serialize access to hardware register and enabled below */
+	struct mutex lock;
+	struct completion conversion_done;
+	void __iomem *regs;
+	struct clk *clk_sense;
+	struct clk *clk_bus;
+	struct reset_control *rst_sense;
+	struct reset_control *rst_bus;
+	bool enabled;
+};
+
+static irqreturn_t sfctemp_isr(int irq, void *data)
+{
+	struct sfctemp *sfctemp = data;
+
+	complete(&sfctemp->conversion_done);
+	return IRQ_HANDLED;
+}
+
+static void sfctemp_power_up(struct sfctemp *sfctemp)
+{
+	/* make sure we're powered down first */
+	writel(SFCTEMP_PD, sfctemp->regs);
+	udelay(1);
+
+	writel(0, sfctemp->regs);
+	/* wait t_pu(50us) + t_rst(100ns) */
+	usleep_range(60, 200);
+
+	/* de-assert reset */
+	writel(SFCTEMP_RSTN, sfctemp->regs);
+	udelay(1); /* wait t_su(500ps) */
+}
+
+static void sfctemp_power_down(struct sfctemp *sfctemp)
+{
+	writel(SFCTEMP_PD, sfctemp->regs);
+}
+
+static void sfctemp_run_single(struct sfctemp *sfctemp)
+{
+	writel(SFCTEMP_RSTN | SFCTEMP_RUN, sfctemp->regs);
+	udelay(1);
+	writel(SFCTEMP_RSTN, sfctemp->regs);

The datasheet (or, rather, programming manual) does not appear
to be public, so I have to guess here.

The code suggests that running a single conversion may be a choice,
not a requirement. If it is indeed a choice, the reasoning needs to be
explained since it adds a lot of complexity and dependencies to the
driver (for example, interrupt support is only mandatory or even needed
due to this choice). It also adds a significant delay to temperature
read operations, which may have practical impact on thermal control
software.

If the chip only supports single temperature readings, that needs to be
explained as well (and why SFCTEMP_RUN has to be reset in that case).

The chip supports continuous conversion. When you set SFCTEMP_RUN, the
temperature raw data will be generated all the time. However, it will
also generate interrupts all the time when the conversion is finished,
because of the hardware limitation. So in this driver, we just support
the single conversion.


Sorry, I don't follow the logic. The interrupt is, for all practical
purposes, useless because there are no limits and exceeding any such
limits is therefore not supported. The only reason to have and enable
to interrupt is because continuous mode is disabled.

The code could be simplified a lot if interrupt support would be
dropped and continuous mode would be enabled.

Guenter

Thank you for your feedback.

Best regards,
Hal




[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux