From: Bjorn Andersson <bjorn.andersson@xxxxxxxxxx> Introduce a binding for GPIO-based mux hardware used for connecting, disconnecting and switching orientation of the SBU lines in USB Type-C applications. Signed-off-by: Bjorn Andersson <bjorn.andersson@xxxxxxxxxx> Signed-off-by: Bjorn Andersson <quic_bjorande@xxxxxxxxxxx> --- Changes since v1: - Expanded the example to indicate how this fits with the TCPM - Updated maintainer email address. .../devicetree/bindings/usb/gpio-sbu-mux.yaml | 110 ++++++++++++++++++ 1 file changed, 110 insertions(+) create mode 100644 Documentation/devicetree/bindings/usb/gpio-sbu-mux.yaml diff --git a/Documentation/devicetree/bindings/usb/gpio-sbu-mux.yaml b/Documentation/devicetree/bindings/usb/gpio-sbu-mux.yaml new file mode 100644 index 000000000000..bf4b1d016e1f --- /dev/null +++ b/Documentation/devicetree/bindings/usb/gpio-sbu-mux.yaml @@ -0,0 +1,110 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: "http://devicetree.org/schemas/usb/gpio-sbu-mux.yaml#"; +$schema: "http://devicetree.org/meta-schemas/core.yaml#"; + +title: GPIO-based SBU mux + +maintainers: + - Bjorn Andersson <andersson@xxxxxxxxxx> + +description: + In USB Type-C applications the SBU lines needs to be connected, disconnected + and swapped depending on the altmode and orientation. This binding describes + a family of hardware solutions which switches between these modes using GPIO + signals. + +properties: + compatible: + items: + - enum: + - onnn,fsusb43l10x + - pericom,pi3usb102 + - const: gpio-sbu-mux + + enable-gpios: + description: Switch enable GPIO + + select-gpios: + description: Orientation select + + vcc-supply: + description: power supply + + mode-switch: + description: Flag the port as possible handle of altmode switching + type: boolean + + orientation-switch: + description: Flag the port as possible handler of orientation switching + type: boolean + + port: + $ref: /schemas/graph.yaml#/properties/port + description: + A port node to link the SBU mux to a TypeC controller for the purpose of + handling altmode muxing and orientation switching. + +required: + - compatible + - enable-gpios + - select-gpios + - mode-switch + - orientation-switch + - port + +additionalProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + + tcpm { + connector { + compatible = "usb-c-connector"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + tcpm_hs_out: endpoint { + remote-endpoint = <&usb_hs_phy_in>; + }; + }; + + port@1 { + reg = <1>; + tcpm_ss_out: endpoint { + remote-endpoint = <&usb_ss_phy_in>; + }; + }; + + port@2 { + reg = <2>; + tcpm_sbu_out: endpoint { + remote-endpoint = <&sbu_mux_in>; + }; + }; + }; + }; + }; + + sbu-mux { + compatible = "pericom,pi3usb102", "gpio-sbu-mux"; + + enable-gpios = <&tlmm 101 GPIO_ACTIVE_LOW>; + select-gpios = <&tlmm 164 GPIO_ACTIVE_HIGH>; + + mode-switch; + orientation-switch; + + port { + sbu_mux_in: endpoint { + remote-endpoint = <&tcpm_sbu_out>; + }; + }; + }; +... -- 2.37.3
