On Wed, Jan 04, 2023 at 02:15:12PM +0530, Sai Krishna Potthuri wrote:
> Add EDAC support for Xilinx ZynqMP OCM Controller, so this driver
> reports CE and UE errors upon interrupt generation, and also creates UE/CE
> debugfs entries for error injection.
> On Xilinx ZynqMP platform, both OCM Controller driver(zynqmp_edac) and
> DDR Memory Controller driver(synopsys_edac) co-exist which means both
> can be loaded at a time. This scenario is tested on Xilinx ZynqMP
> platform.
>
> Fix following issue reported by the robot.
> "MAINTAINERS references a file that doesn't exist:
> Documentation/devicetree/bindings/edac/xlnx,zynqmp-ocmc.yaml"
>
> Co-developed-by: Shubhrajyoti Datta <shubhrajyoti.datta@xxxxxxx>
> Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xxxxxxx>
> Signed-off-by: Sai Krishna Potthuri <sai.krishna.potthuri@xxxxxxx>
> Reported-by: kernel test robot <lkp@xxxxxxxxx>
> ---
> MAINTAINERS | 7 +
> drivers/edac/Kconfig | 9 +
> drivers/edac/Makefile | 1 +
> drivers/edac/zynqmp_edac.c | 465 +++++++++++++++++++++++++++++++++++++
> 4 files changed, 482 insertions(+)
> create mode 100644 drivers/edac/zynqmp_edac.c
Some touchups ontop, see below.
I had to revert back to the #ifdeffery because IS_ENABLED doesn't prevent the
compiler from looking inside the conditional...
Anyway, inter-diff below. Holler if something's still amiss.
Thx.
---
diff --git a/drivers/edac/Kconfig b/drivers/edac/Kconfig
-index 58ab63642e72..7944e40c67da 100644
+index 4cfdefbd744d..68f576700911 100644
--- a/drivers/edac/Kconfig
+++ b/drivers/edac/Kconfig
-@@ -539,4 +539,13 @@ config EDAC_DMC520
+@@ -542,4 +542,12 @@ config EDAC_DMC520
Support for error detection and correction on the
SoCs with ARM DMC-520 DRAM controller.
-+config EDAC_ZYNQMP_OCM
++config EDAC_ZYNQMP
+ tristate "Xilinx ZynqMP OCM Controller"
+ depends on ARCH_ZYNQMP || COMPILE_TEST
+ help
+ This driver supports error detection and correction for the
-+ Xilinx ZynqMP OCM (On Chip Memory) controller.
-+ This driver can also be built as a module. If so, the module
-+ will be called zynqmp_ocm_edac.
++ Xilinx ZynqMP OCM (On Chip Memory) controller. It can also be
++ built as a module. In that case it will be called zynqmp_edac.
+
endif # EDAC
diff --git a/drivers/edac/Makefile b/drivers/edac/Makefile
-index 2d1641a27a28..47cbda06d7b0 100644
+index 2d1641a27a28..9b025c5b3061 100644
--- a/drivers/edac/Makefile
+++ b/drivers/edac/Makefile
@@ -84,3 +84,4 @@ obj-$(CONFIG_EDAC_QCOM) += qcom_edac.o
obj-$(CONFIG_EDAC_ASPEED) += aspeed_edac.o
obj-$(CONFIG_EDAC_BLUEFIELD) += bluefield_edac.o
obj-$(CONFIG_EDAC_DMC520) += dmc520_edac.o
-+obj-$(CONFIG_EDAC_ZYNQMP_OCM) += zynqmp_edac.o
++obj-$(CONFIG_EDAC_ZYNQMP) += zynqmp_edac.o
diff --git a/drivers/edac/zynqmp_edac.c b/drivers/edac/zynqmp_edac.c
new file mode 100644
-index 000000000000..69069028457b
+index 000000000000..b11f1157d4bb
--- /dev/null
+++ b/drivers/edac/zynqmp_edac.c
-@@ -0,0 +1,465 @@
+@@ -0,0 +1,469 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Xilinx ZynqMP OCM ECC Driver
@@ -220,12 +224,14 @@ index 000000000000..69069028457b
+ p->ceinfo.fault_hi = readl(base + CE_FFD1_OFST);
+ p->ceinfo.addr = (OCM_BASEVAL | readl(base + CE_FFA_OFST));
+ writel(ECC_CTRL_CLR_CE_ERR, base + OCM_ISR_OFST);
-+ } else {
++ } else if (mask & OCM_UEINTR_MASK) {
+ p->ue_cnt++;
+ p->ueinfo.fault_lo = readl(base + UE_FFD0_OFST);
+ p->ueinfo.fault_hi = readl(base + UE_FFD1_OFST);
+ p->ueinfo.addr = (OCM_BASEVAL | readl(base + UE_FFA_OFST));
+ writel(ECC_CTRL_CLR_UE_ERR, base + OCM_ISR_OFST);
++ } else {
++ WARN_ON_ONCE(1);
+ }
+}
+
@@ -234,7 +240,7 @@ index 000000000000..69069028457b
+ * @dci: Pointer to the EDAC device instance
+ * @p: Pointer to the OCM ECC status structure
+ *
-+ * Handles the ECC correctable and uncorrectable error.
++ * Handles correctable and uncorrectable errors.
+ */
+static void handle_error(struct edac_device_ctl_info *dci, struct ecc_status *p)
+{
@@ -275,7 +281,7 @@ index 000000000000..69069028457b
+
+ regval = readl(priv->baseaddr + OCM_ISR_OFST);
+ if (!(regval & (OCM_CEINTR_MASK | OCM_UEINTR_MASK))) {
-+ WARN_ONCE(1, "Unhandled IRQ%d.", irq);
++ WARN_ONCE(1, "Unhandled IRQ%d, ISR: 0x%x", irq, regval);
+ return IRQ_NONE;
+ }
+
@@ -403,16 +409,16 @@ index 000000000000..69069028457b
+ if (ret)
+ return ret;
+
-+ ue_bitpos = BIT(priv->ue_bitpos[0]) | BIT(priv->ue_bitpos[1]);
++ if (priv->ue_bitpos[0] > UE_MAX_BITPOS_UPPER ||
++ priv->ue_bitpos[1] > UE_MAX_BITPOS_UPPER)
++ return -EINVAL;
+
+ if (priv->ue_bitpos[0] == priv->ue_bitpos[1]) {
+ edac_printk(KERN_ERR, EDAC_DEVICE, "Bit positions should not be equal\n");
+ return -EINVAL;
+ }
+
-+ if (priv->ue_bitpos[0] > UE_MAX_BITPOS_UPPER ||
-+ priv->ue_bitpos[1] > UE_MAX_BITPOS_UPPER)
-+ return -EINVAL;
++ ue_bitpos = BIT(priv->ue_bitpos[0]) | BIT(priv->ue_bitpos[1]);
+
+ writel((u32)ue_bitpos, priv->baseaddr + OCM_FID0_OFST);
+ writel((u32)(ue_bitpos >> 32), priv->baseaddr + OCM_FID1_OFST);
@@ -492,8 +498,9 @@ index 000000000000..69069028457b
+ /* Enable UE, CE interrupts */
+ writel((OCM_CEINTR_MASK | OCM_UEINTR_MASK), priv->baseaddr + OCM_IEN_OFST);
+
-+ if (IS_ENABLED(CONFIG_EDAC_DEBUG))
-+ setup_debugfs(dci);
++#ifdef CONFIG_EDAC_DEBUG
++ setup_debugfs(dci);
++#endif
+
+ ret = edac_device_add_device(dci);
+ if (ret)
@@ -515,8 +522,9 @@ index 000000000000..69069028457b
+ /* Disable UE, CE interrupts */
+ writel((OCM_CEINTR_MASK | OCM_UEINTR_MASK), priv->baseaddr + OCM_IDS_OFST);
+
-+ if (IS_ENABLED(CONFIG_EDAC_DEBUG))
-+ debugfs_remove_recursive(priv->debugfs_dir);
++#ifdef CONFIG_EDAC_DEBUG
++ debugfs_remove_recursive(priv->debugfs_dir);
++#endif
+
+ edac_device_del_device(&pdev->dev);
+ edac_device_free_ctl_info(dci);
--
Regards/Gruss,
Boris.
https://people.kernel.org/tglx/notes-about-netiquette
