From: Frank Wunderlich <frank-w@xxxxxxxxxxxxxxx> This Series adds some Nodes to mt7986 devicetree and the BananaPi R3 This version is rebased on linux 6.2-rc1 and i dropped already applied Patches from v7. i had run full dtbs-check but i end up with some strange warnings in ethernet-node that should not come up as phy-handle and sfp/managed properties are already defined. These errors also came up for mt7986a-rfb. phy-handle made optional https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/Documentation/devicetree/bindings/net/mediatek,net.yaml#n265 property sfp/managed (which is included for mac subnode in yaml above): https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/Documentation/devicetree/bindings/net/ethernet-controller.yaml#n137 changes: v8: - drop model string override in emmc-dtso - drop cs-gpios from spi-nodes - add interrupt-settings for mt7531 switch v7: - rebase on next so dropped already applied patches - squashed overlay-patch into the bpi-r3 base support - moved regulators from mmc-dts to common dtsi - changed dtsi to dts (as board base dtb) and mmc-dts to overlays - renamed overlays to dtso - removed angelos RB because of changes in bpi-r3 patch v6: - dropped regulators from usb-patch as suggested by chunfeng yun - moved 3v3 regulator to mmc-patch as it is needed for emmc to work rfbs were tested by sam shih, r3 by me - dropped RB from AngeloGioacchino from mmc-patch due to this change - fixed links in coverletter which were broken in v5 - i hope this series is sent without errors now (my mailprovider limited mails last 2 times while sending part 10) v5: - changed usb ranges/reg/unit-adress - added reviewd-by's except usb-part due to changes v4: - dropped RFC prefix - rebase on matthias' mtk dts-next (for 6.2) branch - added author information to overlays - fixed sfp binding error - added fix for moving wed_pcie node - readded missing compatible patches v3: - changed mmc pull-ups - added patch for board binding (sent separately before) - added pcie node in mt7986 (not yet again in r3) - added dt overlays Frank Wunderlich (2): dt-bindings: phy: mediatek,tphy: add support for mt7986 arm64: dts: mt7986: add Bananapi R3 Sam Shih (3): arm64: dts: mt7986: add usb related device nodes arm64: dts: mt7986: add mmc related device nodes arm64: dts: mt7986: add pcie related device nodes .../bindings/phy/mediatek,tphy.yaml | 1 + arch/arm64/boot/dts/mediatek/Makefile | 5 + .../mt7986a-bananapi-bpi-r3-emmc.dtso | 29 ++ .../mt7986a-bananapi-bpi-r3-nand.dtso | 55 +++ .../mediatek/mt7986a-bananapi-bpi-r3-nor.dtso | 68 +++ .../mediatek/mt7986a-bananapi-bpi-r3-sd.dtso | 24 + .../dts/mediatek/mt7986a-bananapi-bpi-r3.dts | 450 ++++++++++++++++++ arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts | 120 +++++ arch/arm64/boot/dts/mediatek/mt7986a.dtsi | 122 +++++ arch/arm64/boot/dts/mediatek/mt7986b-rfb.dts | 8 + 10 files changed, 882 insertions(+) create mode 100644 arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-emmc.dtso create mode 100644 arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-nand.dtso create mode 100644 arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-nor.dtso create mode 100644 arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-sd.dtso create mode 100644 arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3.dts -- 2.34.1
