Re: [PATCHv2 linux-next 4/4] ARM: dts: rockchip: rv1126: Enable Ethernet for Neu2-IO

[Anand Moon <anand@xxxxxxxxxx>]

Hi Johan,

Thanks for your review comments.

On Mon, 26 Dec 2022 at 18:16, Johan Jonker <jbx6244@xxxxxxxxx> wrote:
>
>
>
> On 12/26/22 07:36, Anand Moon wrote:
> > Rockchip RV1126 has GMAC 10/100/1000M ethernet controller.
> > Enable ethernet node on Neu2-IO board.
> >
> > Signed-off-by: Anand Moon <anand@xxxxxxxxxx>
> > ---
> > drop SoB of Jagan Teki
> > ---
> >  arch/arm/boot/dts/rv1126-edgeble-neu2-io.dts | 37 ++++++++++++++++++++
> >  1 file changed, 37 insertions(+)
> >
> > diff --git a/arch/arm/boot/dts/rv1126-edgeble-neu2-io.dts b/arch/arm/boot/dts/rv1126-edgeble-neu2-io.dts
> > index dded0a12f0cd..bd592026eae6 100644
> > --- a/arch/arm/boot/dts/rv1126-edgeble-neu2-io.dts
> > +++ b/arch/arm/boot/dts/rv1126-edgeble-neu2-io.dts
> > @@ -22,6 +22,43 @@ chosen {
> >       };
> >  };
> >
> > +&gmac {
> > +     clock_in_out = "input";
> > +     pinctrl-names = "default";
> > +     pinctrl-0 = <&rgmiim1_pins &clk_out_ethernetm1_pins>;
> > +     phy-mode = "rgmii";
> > +     phy-handle = <&phy>;
>
> > +     assigned-clocks = <&cru CLK_GMAC_SRC>, <&cru CLK_GMAC_TX_RX>,
> > +                     <&cru CLK_GMAC_ETHERNET_OUT>;
>
> align
>
Ok,
> > +     assigned-clock-parents = <&cru CLK_GMAC_SRC_M1>, <&cru RGMII_MODE_CLK>;
> > +     assigned-clock-rates = <125000000>, <0>, <25000000>;
> > +     phy-supply = <&vcc_3v3>;
> > +     tx_delay = <0x2a>;
> > +     rx_delay = <0x1a>;
> > +     status = "okay";
> > +};
> > +
> > +&mdio {
>
> > +     phy: phy@0 {
>
> use ethernet-phy
>
Ok,
> no '#phy-cells' here
>
> > +             compatible = "ethernet-phy-id001c.c916",
> > +                            "ethernet-phy-ieee802.3-c22";
>
> align
>
Ok,
> > +             reg = <0x0>;
> > +             pinctrl-names = "default";
> > +             pinctrl-0 = <&eth_phy_rst>;
> > +             reset-assert-us = <20000>;
> > +             reset-deassert-us = <100000>;
> > +             reset-gpios = <&gpio0 RK_PB6 GPIO_ACTIVE_LOW>;
> > +     };
> > +};
> > +
> > +&pinctrl {
>
> > +     ethernet {
>
> Maybe use a node name more in line with where it is used.
Ok,
>
> > +             eth_phy_rst: eth-phy-rst {
> > +                     rockchip,pins = <0 RK_PB6 RK_FUNC_GPIO &pcfg_pull_down>;
> > +             };
> > +     };
> > +};
> > +
> >  &sdmmc {
> >       bus-width = <4>;
> >       cap-mmc-highspeed;

Thanks
-Anand