On 17.12.2022 00:26, Eric Chanudet wrote:
> Include the dtsi to use a single pmic descriptions.
> Both sa8295p-adp and sa8540p-adp have the same spmi pmic apparently.
>
> Signed-off-by: Eric Chanudet <echanude@xxxxxxxxxx>
> ---
Reviewed-by: Konrad Dybcio <konrad.dybcio@xxxxxxxxxx>
Konrad
> arch/arm64/boot/dts/qcom/sa8295p-adp.dts | 79 +-----------------------
> 1 file changed, 1 insertion(+), 78 deletions(-)
>
> diff --git a/arch/arm64/boot/dts/qcom/sa8295p-adp.dts b/arch/arm64/boot/dts/qcom/sa8295p-adp.dts
> index 84cb6f3eeb56..c8437efe8235 100644
> --- a/arch/arm64/boot/dts/qcom/sa8295p-adp.dts
> +++ b/arch/arm64/boot/dts/qcom/sa8295p-adp.dts
> @@ -11,6 +11,7 @@
> #include <dt-bindings/spmi/spmi.h>
>
> #include "sa8540p.dtsi"
> +#include "sa8540p-pmics.dtsi"
>
> / {
> model = "Qualcomm SA8295P ADP";
> @@ -260,84 +261,6 @@ &remoteproc_nsp1 {
> status = "okay";
> };
>
> -&spmi_bus {
> - pm8450a: pmic@0 {
> - compatible = "qcom,pm8150", "qcom,spmi-pmic";
> - reg = <0x0 SPMI_USID>;
> - #address-cells = <1>;
> - #size-cells = <0>;
> -
> - rtc@6000 {
> - compatible = "qcom,pm8941-rtc";
> - reg = <0x6000>;
> - reg-names = "rtc", "alarm";
> - interrupts = <0x0 0x61 0x1 IRQ_TYPE_NONE>;
> - wakeup-source;
> - };
> -
> - pm8450a_gpios: gpio@c000 {
> - compatible = "qcom,pm8150-gpio", "qcom,spmi-gpio";
> - reg = <0xc000>;
> - gpio-controller;
> - gpio-ranges = <&pm8450a_gpios 0 0 10>;
> - #gpio-cells = <2>;
> - interrupt-controller;
> - #interrupt-cells = <2>;
> - };
> - };
> -
> - pm8450c: pmic@4 {
> - compatible = "qcom,pm8150", "qcom,spmi-pmic";
> - reg = <0x4 SPMI_USID>;
> - #address-cells = <1>;
> - #size-cells = <0>;
> -
> - pm8450c_gpios: gpio@c000 {
> - compatible = "qcom,pm8150-gpio", "qcom,spmi-gpio";
> - reg = <0xc000>;
> - gpio-controller;
> - gpio-ranges = <&pm8450c_gpios 0 0 10>;
> - #gpio-cells = <2>;
> - interrupt-controller;
> - #interrupt-cells = <2>;
> - };
> - };
> -
> - pm8450e: pmic@8 {
> - compatible = "qcom,pm8150", "qcom,spmi-pmic";
> - reg = <0x8 SPMI_USID>;
> - #address-cells = <1>;
> - #size-cells = <0>;
> -
> - pm8450e_gpios: gpio@c000 {
> - compatible = "qcom,pm8150-gpio", "qcom,spmi-gpio";
> - reg = <0xc000>;
> - gpio-controller;
> - gpio-ranges = <&pm8450e_gpios 0 0 10>;
> - #gpio-cells = <2>;
> - interrupt-controller;
> - #interrupt-cells = <2>;
> - };
> - };
> -
> - pm8450g: pmic@c {
> - compatible = "qcom,pm8150", "qcom,spmi-pmic";
> - reg = <0xc SPMI_USID>;
> - #address-cells = <1>;
> - #size-cells = <0>;
> -
> - pm8450g_gpios: gpio@c000 {
> - compatible = "qcom,pm8150-gpio", "qcom,spmi-gpio";
> - reg = <0xc000>;
> - gpio-controller;
> - gpio-ranges = <&pm8450g_gpios 0 0 10>;
> - #gpio-cells = <2>;
> - interrupt-controller;
> - #interrupt-cells = <2>;
> - };
> - };
> -};
> -
> &ufs_mem_hc {
> reset-gpios = <&tlmm 228 GPIO_ACTIVE_LOW>;
>
