Add the pcie2a, pcie2a_phy, and respective tlmm nodes that are needed to get pcie 2a controller enabled on Qdrive3. This patch enables 4GB 64bit memory space for PCIE_2A to have BAR allocations of 64bit pref mem needed on this Qdrive3 platform with dual SoCs for root port and switch NT-EP. Hence this ranges property is overridden in sa8540p-ride.dts only. Signed-off-by: Shazad Hussain <quic_shazhuss@xxxxxxxxxxx> --- Changes since v1: - Fix ranges property indentation (Konrad) This patch depends on below patch series for vreg_l11a. [v4] arm64: dts: qcom: sa8540p-ride: enable PCIe support https://lore.kernel.org/all/20221206161916.315640-1-bmasney@xxxxxxxxxx/ arch/arm64/boot/dts/qcom/sa8540p-ride.dts | 44 +++++++++++++++++++++++ 1 file changed, 44 insertions(+) diff --git a/arch/arm64/boot/dts/qcom/sa8540p-ride.dts b/arch/arm64/boot/dts/qcom/sa8540p-ride.dts index bb4afd3a9632..7ce104fea4f8 100644 --- a/arch/arm64/boot/dts/qcom/sa8540p-ride.dts +++ b/arch/arm64/boot/dts/qcom/sa8540p-ride.dts @@ -146,6 +146,27 @@ vreg_l8g: ldo8 { }; }; +&pcie2a { + ranges = <0x01000000 0x0 0x3c200000 0x0 0x3c200000 0x0 0x100000>, + <0x02000000 0x0 0x3c300000 0x0 0x3c300000 0x0 0x1d00000>, + <0x03000000 0x5 0x00000000 0x5 0x00000000 0x1 0x00000000>; + + perst-gpios = <&tlmm 143 GPIO_ACTIVE_LOW>; + wake-gpios = <&tlmm 145 GPIO_ACTIVE_HIGH>; + + pinctrl-names = "default"; + pinctrl-0 = <&pcie2a_default>; + + status = "okay"; +}; + +&pcie2a_phy { + vdda-phy-supply = <&vreg_l11a>; + vdda-pll-supply = <&vreg_l3a>; + + status = "okay"; +}; + &pcie3a { ranges = <0x01000000 0x0 0x40200000 0x0 0x40200000 0x0 0x100000>, <0x02000000 0x0 0x40300000 0x0 0x40300000 0x0 0x20000000>, @@ -247,6 +268,29 @@ &xo_board_clk { /* PINCTRL */ &tlmm { + pcie2a_default: pcie2a-default-state { + perst-pins { + pins = "gpio143"; + function = "gpio"; + drive-strength = <2>; + bias-pull-down; + }; + + clkreq-pins { + pins = "gpio142"; + function = "pcie2a_clkreq"; + drive-strength = <2>; + bias-pull-up; + }; + + wake-pins { + pins = "gpio145"; + function = "gpio"; + drive-strength = <2>; + bias-pull-up; + }; + }; + pcie3a_default: pcie3a-default-state { perst-pins { pins = "gpio151"; -- 2.38.0
