Hi Marek, Am Freitag, 9. Dezember 2022, 13:02:10 CET schrieb Marek Vasut: > On 12/9/22 10:36, Alexander Stein wrote: > > Hello Krzysztof, > > Hi, > > > Am Freitag, 9. Dezember 2022, 10:07:45 CET schrieb Krzysztof Kozlowski: > >> On 09/12/2022 09:54, Alexander Stein wrote: > >>> Hello Krzysztof, > >>> > >>> thanks for the fast feedback. > >>> > >>> Am Freitag, 9. Dezember 2022, 09:39:49 CET schrieb Krzysztof Kozlowski: > >>>> On 09/12/2022 09:33, Alexander Stein wrote: > >>>>> It takes some time until the enable GPIO has settled when turning on. > >>>>> This delay is platform specific and may be caused by e.g. voltage > >>>>> shifts, capacitors etc. > >>>>> > >>>>> Signed-off-by: Alexander Stein <alexander.stein@xxxxxxxxxxxxxxx> > >>>>> --- > >>>>> > >>>>> .../devicetree/bindings/display/bridge/ti,sn65dsi83.yaml | 4 > >>>>> ++++ > >>>>> 1 file changed, 4 insertions(+) > >>>>> > >>>>> diff --git > >>>>> a/Documentation/devicetree/bindings/display/bridge/ti,sn65dsi83.yaml > >>>>> b/Documentation/devicetree/bindings/display/bridge/ti,sn65dsi83.yaml > >>>>> index 48a97bb3e2e0d..3f50d497cf8ac 100644 > >>>>> --- > >>>>> a/Documentation/devicetree/bindings/display/bridge/ti,sn65dsi83.yaml > >>>>> +++ > >>>>> b/Documentation/devicetree/bindings/display/bridge/ti,sn65dsi83.yaml > >>>>> > >>>>> @@ -32,6 +32,10 @@ properties: > >>>>> maxItems: 1 > >>>>> description: GPIO specifier for bridge_en pin (active high). > >>>>> > >>>>> + ti,enable-delay-us: > >>>>> + default: 10000 > >>>>> + description: Enable time delay for enable-gpios > >>>> > >>>> Aren't you now mixing two separate delays? One for entire block on (I > >>>> would assume mostly fixed delay) and one depending on regulators > >>>> (regulator-ramp-delay, regulator-enable-ramp-delay). Maybe you miss the > >>>> second delays in your power supply? If so, the first one might be fixed > >>>> and hard-coded in the driver? > >>> > >>> Apparently there are two different delays: reset time (t_reset) of 10ms > >>> as > >>> specified by datasheet. This is already ensured by a following delay > >>> after > >>> requesting enable_gpio as low and switching the GPIO to low in disable > >>> path. > >>> > >>> When enabling this GPIO it takes some time until it is valid on the > >>> chip, > >>> this is what this series is about. It's highly platform specific. > >>> > >>> Unfortunately this is completely unrelated to the vcc-supply regulator. > >>> This one has to be enabled before the enable GPIO can be enabled. So > >>> there is no regulator-ramp-delay. > >> > >> Your driver does one after another - regulator followed immediately by > >> gpio - so this as well can be a delay from regulator (maybe not ramp but > >> enable delay). > > The chip has two separate input pins: > > VCC -- power supply that's regulator > EN -- reset line, that's GPIO > > Alexander is talking about EN line here. > > > But this will introduce a section which must not be interrupted or > > delayed. > > This is impossible as the enable gpio is attached to an i2c expander in my > > case. > > > > Given the following time chart: > > vcc set EN > > > > enable GPIO PAD > > > > | |<-- t_raise -->| > > | > > | <-- t_vcc_gpio --> | | > > | <-- t_enable_delay --> | > > > > t_raise is the time from changing the GPIO output at the expander until > > voltage on the EN (input) pad from the bridge has reached high voltage > > level. This is an electrical characteristic I can not change and have to > > take into account. > > t_vcc_gpio is the time from enabling supply voltage to enabling the bridge > > (removing from reset). Minimum t_vcc_gpio is something which can be > > addressed by the regulator and is no problem so far. But there is no > > upper bound to it. > What exactly is your EN signal rise time (should be ns or so)? Can you > look at that with a scope , maybe even with relation to the VCC regulator ? I checked EN rise time using a scope, it's ~110ms. I not an expert in hardware but on the mainboard there is some capacitor attached to this line, which increased the time, independent from the internal pull-up. > The DSI84 EN pin already has a built-in pullup per DSI84 datasheet (see > Table 5-1. Pin Functions), so that should make the signal rise fast, > certainly not for seconds. Here it is >100ms, so the current waiting time is far too less. This results in errors regarding PLL lock failure. Best regards, Alexander
