Re: [PATCH v4 1/2] dt-bindings: media: i2c: Add IMX519 CMOS sensor binding

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On 05/12/2022 03:38, lee.jackson wrote:
> Add YAML device tree binding for IMX519 CMOS image sensor, and
> the relevant MAINTAINERS entries.
> 
> Signed-off-by: lee.jackson <lee.jackson@xxxxxxxxxxx >

That's still not correct entry. Except trailing space, are you sure that
in your documents (national ID, passport) the Latin transliteration of
your name is with a dot between names? Since it is a third try, it's
getting more and more confusing.

> ---
>  .../bindings/media/i2c/sony,imx519.yaml       | 107 ++++++++++++++++++
>  MAINTAINERS                                   |   8 ++
>  2 files changed, 115 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/media/i2c/sony,imx519.yaml
> 
> diff --git a/Documentation/devicetree/bindings/media/i2c/sony,imx519.yaml b/Documentation/devicetree/bindings/media/i2c/sony,imx519.yaml
> new file mode 100644
> index 000000000000..d7ca16cfbacc
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/media/i2c/sony,imx519.yaml
> @@ -0,0 +1,107 @@
> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/media/i2c/sony,imx519.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: Sony 1/2.5-Inch 16Mpixel CMOS Digital Image Sensor
> +
> +maintainers:
> +  - lee.jackson <lee.jackson@xxxxxxxxxxx>

Same question.

> +
> +description: |-
> +  The Sony IMX519 is a 1/2.5-inch CMOS active pixel digital image sensor
> +  with an active array size of 4656H x 3496V. It is programmable through
> +  I2C interface. The I2C address is fixed to 0x1A as per sensor data sheet.
> +  Image data is sent through MIPI CSI-2, which is configured as either 2 or
> +  4 data lanes.
> +
> +properties:
> +  compatible:
> +    const: sony,imx519
> +
> +  reg:
> +    maxItems: 1
> +
> +  clocks:
> +    maxItems: 1
> +
> +  vdig-supply:
> +    description:
> +      Digital I/O voltage supply, 1.05 volts
> +
> +  vana-supply:
> +    description:
> +      Analog voltage supply, 2.8 volts
> +
> +  vddl-supply:
> +    description:
> +      Digital core voltage supply, 1.8 volts
> +
> +  reset-gpios:

maxItems: 1

> +    description: |-

No need for |-

> +      Reference to the GPIO connected to the xclr pin, if any.
> +      Must be released (set high) after all supplies and INCK are applied.
> +
> +  port:
> +    $ref: /schemas/graph.yaml#/$defs/port-base
> +    additionalProperties: false
> +
Best regards,
Krzysztof




[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux