[PATCH v2 00/15] thermal/drivers/tsens: specify nvmem cells in DT rather than parsing them manually

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Historically the tsens driver fetches the calibration data as a blob and
then parses the blob on its own. This results in semi-duplicated code
spreading over the platform-specific functions.

This patch series changes tsens calibration code to per-value nvmem
cells rather than parsing the blob in the driver. For backwards
compatibility the old code is left in place for msm8916, msm8974 and
qcs404, the platforms which have in-tree DT files. For all other
affected platforms the old parsing code has been dropped as a part of
this series.

The code was tested on msm8916 and qcs404 only.

Note: the DTs changes depend on driver changes. Tsens driver will not
work if DT patches are merged, but the driver bits are not. As the
thermal sense is critical for device safety, I'd suggest merging binding
and driver during one merge window and then merging DT changes in the
next merge window.

Changes since the RFC:
- Sorted out the msm8976/msm8956, custom slopes are used only for msm8956,
- Implemented proper support for msm8974/apq8084,
- Added tsens_calibrate_common() and ops_v0_1 which can be used in
  common cases,
- Removed superfluous identity hw_ids
- Fixed calibration calculation in tsens_calibrate_nvmem() for
  ONE_PT_CALIB case

Dmitry Baryshkov (15):
  dt-bindings: thermal: tsens: add msm8956 compat
  dt-bindings: thermal: tsens: support per-sensor calibration cells
  dt-bindings: thermal: tsens: add per-sensor cells for msm8974
  thermal/drivers/tsens: Drop unnecessary hw_ids
  thermal/drivers/tsens: Drop msm8976-specific defines
  thermal/drivers/tsens: Sort out msm8976 vs msm8956 data
  thermal/drivers/tsens: Support using nvmem cells for calibration data
  thermal/drivers/tsens: Drop single-cell code for msm8939
  thermal/drivers/tsens: Drop single-cell code for mdm9607
  thermal/drivers/tsens: Drop single-cell code for msm8976/msm8956
  thermal/drivers/tsens: Support using nvmem cells for msm8974
    calibration
  arm64: dts: qcom: msm8916: specify per-sensor calibration cells
  arm64: dts: qcom: qcs404: specify per-sensor calibration cells
  ARM: dts: qcom-msm8974: specify per-sensor calibration cells
  ARM: dts: qcom-apq8084: specify per-sensor calibration cells

 .../bindings/thermal/qcom-tsens.yaml          | 123 +++++++-
 arch/arm/boot/dts/qcom-apq8084.dtsi           | 262 ++++++++++++++++-
 arch/arm/boot/dts/qcom-msm8974.dtsi           | 262 ++++++++++++++++-
 arch/arm64/boot/dts/qcom/msm8916.dtsi         |  70 ++++-
 arch/arm64/boot/dts/qcom/qcs404.dtsi          | 121 +++++++-
 drivers/thermal/qcom/tsens-v0_1.c             | 267 ++++--------------
 drivers/thermal/qcom/tsens-v1.c               | 190 +++----------
 drivers/thermal/qcom/tsens.c                  | 102 +++++++
 drivers/thermal/qcom/tsens.h                  |   8 +-
 9 files changed, 1002 insertions(+), 403 deletions(-)

-- 
2.35.1




[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux