Re: [PATCH v5 2/2] arm64: dts: qcom: sc7280: Add DT for sc7280-herobrine-zombie

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Hi,

On Fri, Nov 25, 2022 at 1:45 AM Owen Yang <ecs.taipeikernel@xxxxxxxxx> wrote:
>
> diff --git a/arch/arm64/boot/dts/qcom/sc7280-herobrine-zombie.dtsi b/arch/arm64/boot/dts/qcom/sc7280-herobrine-zombie.dtsi
> new file mode 100644
> index 000000000000..d10362ecdafb
> --- /dev/null
> +++ b/arch/arm64/boot/dts/qcom/sc7280-herobrine-zombie.dtsi
> @@ -0,0 +1,313 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +/*
> + * Google Zombie board device tree source
> + *
> + * Copyright 2022 Google LLC.
> + */
> +
> +#include "sc7280-herobrine.dtsi"
> +#include "sc7280-herobrine-audio-rt5682.dtsi"
> +
> +/*
> + * ADDITIONS TO FIXED REGULATORS DEFINED IN PARENT DEVICE TREE FILES
> + *
> + * Sort order matches the order in the parent files (parents before children).
> + */
> +
> +&pp3300_codec {
> +       status = "okay";
> +};
> +
> +/* ADDITIONS TO NODES DEFINED IN PARENT DEVICE TREE FILES */
> +
> +ap_tp_i2c: &i2c0 {
> +       clock-frequency = <400000>;
> +       status = "okay";
> +
> +       trackpad: trackpad@15 {
> +               compatible = "hid-over-i2c";
> +               reg = <0x15>;
> +               pinctrl-names = "default";
> +               pinctrl-0 = <&tp_int_odl>;
> +
> +               interrupt-parent = <&tlmm>;
> +               interrupts = <7 IRQ_TYPE_EDGE_FALLING>;
> +
> +               hid-descr-addr = <0x01>;
> +               vdd-supply = <&pp3300_z1>;
> +               post-power-on-delay-ms = <100>;

Do you have any documentation pointing to 100 ms really being needed
here? I know that leaving this number off is rarely a good idea, but
arbitrarily picking 100 isn't great either. It could either be much
too big or much too small.


> +               wakeup-source;
> +       };
> +};
> +
> +&ap_sar_sensor_i2c {
> +       status = "okay";
> +};
> +
> +&ap_sar_sensor0 {
> +       status = "okay";
> +};
> +
> +&ap_sar_sensor1 {
> +       status = "okay";
> +};
> +
> +&mdss_edp {
> +       status = "okay";
> +};
> +
> +&mdss_edp_phy {
> +       status = "okay";
> +};
> +
> +/* For nvme */
> +&pcie1 {
> +       status = "okay";
> +};
> +
> +/* For nvme */
> +&pcie1_phy {
> +       status = "okay";
> +};
> +
> +&pwmleds {
> +       status = "okay";
> +};
> +
> +/* For eMMC */
> +&sdhc_1 {
> +       status = "okay";
> +};
> +
> +/* PINCTRL - ADDITIONS TO NODES IN PARENT DEVICE TREE FILES */
> +
> +&ts_rst_conn {
> +       bias-disable;
> +};
> +
> +/* PINCTRL - BOARD-SPECIFIC */
> +
> +/*
> + * Methodology for gpio-line-names:
> + * - If a pin goes to herobrine board and is named it gets that name.
> + * - If a pin goes to herobrine board and is not named, it gets no name.
> + * - If a pin is totally internal to Qcard then it gets Qcard name.
> + * - If a pin is not hooked up on Qcard, it gets no name.
> + */
> +
> +&pm8350c_gpios {
> +       gpio-line-names = "FLASH_STROBE_1",             /* 1 */
> +                         "AP_SUSPEND",
> +                         "PM8008_1_RST_N",
> +                         "",
> +                         "",
> +                         "",
> +                         "PMIC_EDP_BL_EN",
> +                         "PMIC_EDP_BL_PWM",
> +                         "";
> +};
> +
> +&pm8350c_pwm_backlight{
> +       pwms = <&pm8350c_pwm 3 200000>;
> +};

This is not a pinctrl update so it doesn't belong in the "PINCTRL"
section. Please move this above right before the "pwmleds" node.

Having a comment like "Set the PWM period to 200 microseconds (5kHz
duty cycle") wouldn't hurt either.


> +&tlmm {
> +       gpio-line-names = "AP_TP_I2C_SDA",              /* 0 */
> +                         "AP_TP_I2C_SCL",
> +                         "SSD_RST_L",
> +                         "PE_WAKE_ODL",
> +                         "AP_SAR_SDA",
> +                         "AP_SAR_SCL",
> +                         "PRB_SC_GPIO_6",
> +                         "TP_INT_ODL",
> +                         "HP_I2C_SDA",
> +                         "HP_I2C_SCL",
> +
> +                         "GNSS_L1_EN",                 /* 10 */
> +                         "GNSS_L5_EN",
> +                         "SPI_AP_MOSI",
> +                         "SPI_AP_MISO",
> +                         "SPI_AP_CLK",
> +                         "SPI_AP_CS0_L",
> +                         /*
> +                          * AP_FLASH_WP is crossystem ABI. Schematics
> +                          * call it BIOS_FLASH_WP_OD.
> +                          */
> +                         "AP_FLASH_WP",
> +                         "",
> +                         "AP_EC_INT_L",
> +                         "",
> +
> +                         "UF_CAM_RST_L",               /* 20 */
> +                         "WF_CAM_RST_L",
> +                         "UART_AP_TX_DBG_RX",
> +                         "UART_DBG_TX_AP_RX",
> +                         "",
> +                         "PM8008_IRQ_1",
> +                         "HOST2WLAN_SOL",
> +                         "WLAN2HOST_SOL",
> +                         "MOS_BT_UART_CTS",
> +                         "MOS_BT_UART_RFR",
> +
> +                         "MOS_BT_UART_TX",             /* 30 */
> +                         "MOS_BT_UART_RX",
> +                         "PRB_SC_GPIO_32",
> +                         "HUB_RST_L",
> +                         "",
> +                         "",
> +                         "AP_SPI_FP_MISO",
> +                         "AP_SPI_FP_MOSI",
> +                         "AP_SPI_FP_CLK",
> +                         "AP_SPI_FP_CS_L",
> +
> +                         "AP_EC_SPI_MISO",             /* 40 */
> +                         "AP_EC_SPI_MOSI",
> +                         "AP_EC_SPI_CLK",
> +                         "AP_EC_SPI_CS_L",
> +                         "LCM_RST_L",
> +                         "EARLY_EUD_N",
> +                         "",
> +                         "DP_HOT_PLUG_DET",
> +                         "IO_BRD_MLB_ID0",
> +                         "IO_BRD_MLB_ID1",
> +
> +                         "IO_BRD_MLB_ID2",             /* 50 */
> +                         "SSD_EN",
> +                         "TS_I2C_SDA_CONN",
> +                         "TS_I2C_CLK_CONN",
> +                         "TS_RST_CONN",
> +                         "TS_INT_CONN",
> +                         "AP_I2C_TPM_SDA",
> +                         "AP_I2C_TPM_SCL",
> +                         "PRB_SC_GPIO_58",
> +                         "PRB_SC_GPIO_59",
> +
> +                         "EDP_HOT_PLUG_DET_N",         /* 60 */
> +                         "FP_TO_AP_IRQ_L",
> +                         "",
> +                         "AMP_EN",
> +                         "CAM0_MCLK_GPIO_64",
> +                         "CAM1_MCLK_GPIO_65",
> +                         "WF_CAM_MCLK",
> +                         "PRB_SC_GPIO_67",
> +                         "FPMCU_BOOT0",
> +                         "UF_CAM_SDA",
> +
> +                         "UF_CAM_SCL",                 /* 70 */
> +                         "",
> +                         "",
> +                         "WF_CAM_SDA",
> +                         "WF_CAM_SCL",
> +                         "",
> +                         "",
> +                         "EN_FP_RAILS",
> +                         "FP_RST_L",
> +                         "PCIE1_CLKREQ_ODL",
> +
> +                         "EN_PP3300_DX_EDP",           /* 80 */
> +                         "US_EURO_HS_SEL",
> +                         "FORCED_USB_BOOT",
> +                         "WCD_RESET_N",
> +                         "MOS_WLAN_EN",
> +                         "MOS_BT_EN",
> +                         "MOS_SW_CTRL",
> +                         "MOS_PCIE0_RST",
> +                         "MOS_PCIE0_CLKREQ_N",
> +                         "MOS_PCIE0_WAKE_N",
> +
> +                         "MOS_LAA_AS_EN",              /* 90 */
> +                         "SD_CD_ODL",
> +                         "",
> +                         "",
> +                         "MOS_BT_WLAN_SLIMBUS_CLK",
> +                         "MOS_BT_WLAN_SLIMBUS_DAT0",
> +                         "HP_MCLK",
> +                         "HP_BCLK",
> +                         "HP_DOUT",
> +                         "HP_DIN",
> +
> +                         "HP_LRCLK",                   /* 100 */
> +                         "HP_IRQ",
> +                         "",
> +                         "",
> +                         "GSC_AP_INT_ODL",
> +                         "EN_PP3300_CODEC",
> +                         "AMP_BCLK",
> +                         "AMP_DIN",
> +                         "AMP_LRCLK",
> +                         "UIM1_DATA_GPIO_109",
> +
> +                         "UIM1_CLK_GPIO_110",          /* 110 */
> +                         "UIM1_RESET_GPIO_111",
> +                         "PRB_SC_GPIO_112",
> +                         "UIM0_DATA",
> +                         "UIM0_CLK",
> +                         "UIM0_RST",
> +                         "UIM0_PRESENT_ODL",
> +                         "SDM_RFFE0_CLK",
> +                         "SDM_RFFE0_DATA",
> +                         "WF_CAM_EN",
> +
> +                         "FASTBOOT_SEL_0",             /* 120 */
> +                         "SC_GPIO_121",
> +                         "FASTBOOT_SEL_1",
> +                         "SC_GPIO_123",
> +                         "FASTBOOT_SEL_2",
> +                         "SM_RFFE4_CLK_GRFC_8",
> +                         "SM_RFFE4_DATA_GRFC_9",
> +                         "WLAN_COEX_UART1_RX",
> +                         "WLAN_COEX_UART1_TX",
> +                         "PRB_SC_GPIO_129",
> +
> +                         "LCM_ID0",                    /* 130 */
> +                         "LCM_ID1",
> +                         "",
> +                         "SDR_QLINK_REQ",
> +                         "SDR_QLINK_EN",
> +                         "QLINK0_WMSS_RESET_N",
> +                         "SMR526_QLINK1_REQ",
> +                         "SMR526_QLINK1_EN",
> +                         "SMR526_QLINK1_WMSS_RESET_N",
> +                         "PRB_SC_GPIO_139",
> +
> +                         "SAR1_IRQ_ODL",               /* 140 */
> +                         "SAR0_IRQ_ODL",
> +                         "PRB_SC_GPIO_142",
> +                         "",
> +                         "WCD_SWR_TX_CLK",
> +                         "WCD_SWR_TX_DATA0",
> +                         "WCD_SWR_TX_DATA1",
> +                         "WCD_SWR_RX_CLK",
> +                         "WCD_SWR_RX_DATA0",
> +                         "WCD_SWR_RX_DATA1",
> +
> +                         "DMIC01_CLK",                 /* 150 */
> +                         "DMIC01_DATA",
> +                         "DMIC23_CLK",
> +                         "DMIC23_DATA",
> +                         "",
> +                         "",
> +                         "EC_IN_RW_ODL",
> +                         "HUB_EN",
> +                         "WCD_SWR_TX_DATA2",
> +                         "",
> +
> +                         "",                           /* 160 */
> +                         "",
> +                         "",
> +                         "",
> +                         "",
> +                         "",
> +                         "",
> +                         "",
> +                         "",
> +                         "",
> +
> +                         "",                           /* 170 */
> +                         "MOS_BLE_UART_TX",
> +                         "MOS_BLE_UART_RX",
> +                         "",
> +                         "",
> +                         "";

There is still one extra entry in "gpio-line-names". Said another way,
the max GPIO number on sc7280 is GPIO 174. As you can see above, GPIO
170 is unnamed (it has a blank string). GPIO 171 has the name
"MOS_BLE_UART_TX", GPIO 172 has "MOS_BLE_UART_RX", and then you have
blank names for GPIO 173, 174, and 175. ...but there is no GPIO 175.

So, simply put, please remove one of the lines after the line with
"MOS_BLE_UART_RX"

-Doug



[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux