> D1 (aka D1-H), D1s (aka F133), R528, and T113 are a family of SoCs based
> on a single die, or at a pair of dies derived from the same design.
>
> D1 and D1s contain a single T-HEAD Xuantie C906 CPU, whereas R528 and
> T113 contain a pair of Cortex-A7's. D1 and R528 are the full version of
> the chip with a BGA package, whereas D1s and T113 are low-pin-count QFP
> variants.
>
> Because the original design supported both ARM and RISC-V CPUs, some
> peripherals are duplicated. In addition, all variants except D1s contain
> a HiFi 4 DSP with its own set of peripherals.
>
> The devicetrees are organized to minimize duplication:
> - Common perhiperals are described in sunxi-d1s-t113.dtsi
> - DSP-related peripherals are described in sunxi-d1-t113.dtsi
> - RISC-V specific hardware is described in sun20i-d1s.dtsi
> - Functionality unique to the D1 variant is described in sun20i-d1.dtsi
>
> The SOC_PERIPHERAL_IRQ macro handles the different #interrupt-cells
> values between the ARM (GIC) and RISC-V (PLIC) versions of the SoC.
>
> Signed-off-by: Samuel Holland <samuel@xxxxxxxxxxxx>
> ---
>
> Changes in v2:
> - Split into separate files for sharing with D1s/R528/T113
> - Use SOC_PERIPHERAL_IRQ macro for interrupts
> - Rename osc24M to dcxo and move the frequency to the board DTs
> - Drop analog LDOs due to the missing binding
> - Correct tcon_top DSI clock reference
> - Add DMIC, DSI controller, and DPHY (bindings are in linux-next)
> - Add CPU OPP table
>
> arch/riscv/boot/dts/allwinner/sun20i-d1.dtsi | 66 ++
> arch/riscv/boot/dts/allwinner/sun20i-d1s.dtsi | 76 ++
> .../boot/dts/allwinner/sunxi-d1-t113.dtsi | 15 +
> .../boot/dts/allwinner/sunxi-d1s-t113.dtsi | 844 ++++++++++++++++++
> 4 files changed, 1001 insertions(+)
> create mode 100644 arch/riscv/boot/dts/allwinner/sun20i-d1.dtsi
> create mode 100644 arch/riscv/boot/dts/allwinner/sun20i-d1s.dtsi
> create mode 100644 arch/riscv/boot/dts/allwinner/sunxi-d1-t113.dtsi
> create mode 100644 arch/riscv/boot/dts/allwinner/sunxi-d1s-t113.dtsi
<snip>
> +++ b/arch/riscv/boot/dts/allwinner/sun20i-d1s.dtsi
> @@ -0,0 +1,76 @@
> +// SPDX-License-Identifier: (GPL-2.0+ or MIT)
> +// Copyright (C) 2021-2022 Samuel Holland <samuel@xxxxxxxxxxxx>
> +
> +#define SOC_PERIPHERAL_IRQ(nr) (nr + 16)
> +
> +#include "sunxi-d1s-t113.dtsi"
> +
> +/ {
> + cpus {
> + timebase-frequency = <24000000>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + cpu0: cpu@0 {
> + compatible = "thead,c906", "riscv";
> + device_type = "cpu";
> + reg = <0>;
> + clocks = <&ccu CLK_RISCV>;
> + d-cache-block-size = <64>;
> + d-cache-sets = <256>;
> + d-cache-size = <32768>;
> + i-cache-block-size = <64>;
> + i-cache-sets = <128>;
> + i-cache-size = <32768>;
> + mmu-type = "riscv,sv39";
> + operating-points-v2 = <&opp_table_cpu>;
> + riscv,isa = "rv64imafdc";
> + #cooling-cells = <2>;
> +
> + cpu0_intc: interrupt-controller {
> + compatible = "riscv,cpu-intc";
> + interrupt-controller;
> + #address-cells = <0>;
> + #interrupt-cells = <1>;
> + };
> + };
> + };
> +
> + opp_table_cpu: opp-table-cpu {
> + compatible = "operating-points-v2";
> +
> + opp-408000000 {
> + opp-hz = /bits/ 64 <408000000>;
> + opp-microvolt = <900000 900000 1100000>;
> + };
> +
> + opp-1080000000 {
> + opp-hz = /bits/ 64 <1008000000>;
> + opp-microvolt = <900000 900000 1100000>;
> + };
> + };
> +
> + soc {
> + interrupt-parent = <&plic>;
> +
> + riscv_wdt: watchdog@6011000 {
> + compatible = "allwinner,sun20i-d1-wdt";
> + reg = <0x6011000 0x20>;
> + interrupts = <SOC_PERIPHERAL_IRQ(131) IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&dcxo>, <&rtc CLK_OSC32K>;
> + clock-names = "hosc", "losc";
> + };
> +
> + plic: interrupt-controller@10000000 {
> + compatible = "allwinner,sun20i-d1-plic",
> + "thead,c900-plic";
> + reg = <0x10000000 0x4000000>;
> + interrupts-extended = <&cpu0_intc 11>,
> + <&cpu0_intc 9>;
> + interrupt-controller;
> + riscv,ndev = <176>;
The D1-H user manual says starting from interrupt number 176, interrupts are
CPUX related which I assume are CPU internal interrupts?
If yes, for external ones, valid interrupt source range is [1, 175]. And this
field should be 175, no?
> + #address-cells = <0>;
> + #interrupt-cells = <2>;
> + };
> + };
> +};
<snip>
Regards,
Bin
