Split MediaTek ECC engine with rawnand controller and convert to YAML schema. Signed-off-by: Xiangsheng Hou <xiangsheng.hou@xxxxxxxxxxxx> --- .../bindings/mtd/mtk,nand-ecc-engine.yaml | 60 ++++++ .../devicetree/bindings/mtd/mtk-nand.txt | 176 ------------------ .../devicetree/bindings/mtd/mtk-nand.yaml | 92 +++++++++ 3 files changed, 152 insertions(+), 176 deletions(-) create mode 100644 Documentation/devicetree/bindings/mtd/mtk,nand-ecc-engine.yaml delete mode 100644 Documentation/devicetree/bindings/mtd/mtk-nand.txt create mode 100644 Documentation/devicetree/bindings/mtd/mtk-nand.yaml diff --git a/Documentation/devicetree/bindings/mtd/mtk,nand-ecc-engine.yaml b/Documentation/devicetree/bindings/mtd/mtk,nand-ecc-engine.yaml new file mode 100644 index 000000000000..80321157e928 --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/mtk,nand-ecc-engine.yaml @@ -0,0 +1,60 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/mtd/mtk,nand-ecc-engine.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: MediaTek(MTK) SoCs NAND ECC engine + +maintainers: + - Xiangsheng Hou <xiangsheng.hou@xxxxxxxxxxxx> + +description: | + MTK NAND ECC engine can cowork with MTK raw NAND and SPI NAND controller. + +properties: + compatible: + enum: + - mediatek,mt2701-ecc + - mediatek,mt2712-ecc + - mediatek,mt7622-ecc + + reg: + items: + - description: Base physical address and size of ECC. + + interrupts: + items: + - description: ECC interrupt + + clocks: + minItems: 1 + items: + - description: clock used for the controller + +required: + - compatible + - reg + - interrupts + - clocks + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/clock/mt2701-clk.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/interrupt-controller/irq.h> + + soc { + #address-cells = <2>; + #size-cells = <2>; + + bch: ecc@1100e000 { + compatible = "mediatek,mt2701-ecc"; + reg = <0 0x1100e000 0 0x1000>; + interrupts = <GIC_SPI 55 IRQ_TYPE_LEVEL_LOW>; + clocks = <&pericfg CLK_PERI_NFI_ECC>; + }; + }; + diff --git a/Documentation/devicetree/bindings/mtd/mtk-nand.txt b/Documentation/devicetree/bindings/mtd/mtk-nand.txt deleted file mode 100644 index 4d3ec5e4ff8a..000000000000 --- a/Documentation/devicetree/bindings/mtd/mtk-nand.txt +++ /dev/null @@ -1,176 +0,0 @@ -MTK SoCs NAND FLASH controller (NFC) DT binding - -This file documents the device tree bindings for MTK SoCs NAND controllers. -The functional split of the controller requires two drivers to operate: -the nand controller interface driver and the ECC engine driver. - -The hardware description for both devices must be captured as device -tree nodes. - -1) NFC NAND Controller Interface (NFI): -======================================= - -The first part of NFC is NAND Controller Interface (NFI) HW. -Required NFI properties: -- compatible: Should be one of - "mediatek,mt2701-nfc", - "mediatek,mt2712-nfc", - "mediatek,mt7622-nfc". -- reg: Base physical address and size of NFI. -- interrupts: Interrupts of NFI. -- clocks: NFI required clocks. -- clock-names: NFI clocks internal name. -- ecc-engine: Required ECC Engine node. -- #address-cells: NAND chip index, should be 1. -- #size-cells: Should be 0. - -Example: - - nandc: nfi@1100d000 { - compatible = "mediatek,mt2701-nfc"; - reg = <0 0x1100d000 0 0x1000>; - interrupts = <GIC_SPI 56 IRQ_TYPE_LEVEL_LOW>; - clocks = <&pericfg CLK_PERI_NFI>, - <&pericfg CLK_PERI_NFI_PAD>; - clock-names = "nfi_clk", "pad_clk"; - ecc-engine = <&bch>; - #address-cells = <1>; - #size-cells = <0>; - }; - -Platform related properties, should be set in {platform_name}.dts: -- children nodes: NAND chips. - -Children nodes properties: -- reg: Chip Select Signal, default 0. - Set as reg = <0>, <1> when need 2 CS. -Optional: -- nand-on-flash-bbt: Store BBT on NAND Flash. -- nand-ecc-mode: the NAND ecc mode (check driver for supported modes) -- nand-ecc-step-size: Number of data bytes covered by a single ECC step. - valid values: - 512 and 1024 on mt2701 and mt2712. - 512 only on mt7622. - 1024 is recommended for large page NANDs. -- nand-ecc-strength: Number of bits to correct per ECC step. - The valid values that each controller supports: - mt2701: 4, 6, 8, 10, 12, 14, 16, 18, 20, 22, 24, 28, - 32, 36, 40, 44, 48, 52, 56, 60. - mt2712: 4, 6, 8, 10, 12, 14, 16, 18, 20, 22, 24, 28, - 32, 36, 40, 44, 48, 52, 56, 60, 68, 72, 80. - mt7622: 4, 6, 8, 10, 12, 14, 16. - The strength should be calculated as follows: - E = (S - F) * 8 / B - S = O / (P / Q) - E : nand-ecc-strength. - S : spare size per sector. - F : FDM size, should be in the range [1,8]. - It is used to store free oob data. - O : oob size. - P : page size. - Q : nand-ecc-step-size. - B : number of parity bits needed to correct - 1 bitflip. - According to MTK NAND controller design, - this number depends on max ecc step size - that MTK NAND controller supports. - If max ecc step size supported is 1024, - then it should be always 14. And if max - ecc step size is 512, then it should be - always 13. - If the result does not match any one of the listed - choices above, please select the smaller valid value from - the list. - (otherwise the driver will do the adjustment at runtime) -- pinctrl-names: Default NAND pin GPIO setting name. -- pinctrl-0: GPIO setting node. - -Example: - &pio { - nand_pins_default: nanddefault { - pins_dat { - pinmux = <MT2701_PIN_111_MSDC0_DAT7__FUNC_NLD7>, - <MT2701_PIN_112_MSDC0_DAT6__FUNC_NLD6>, - <MT2701_PIN_114_MSDC0_DAT4__FUNC_NLD4>, - <MT2701_PIN_118_MSDC0_DAT3__FUNC_NLD3>, - <MT2701_PIN_121_MSDC0_DAT0__FUNC_NLD0>, - <MT2701_PIN_120_MSDC0_DAT1__FUNC_NLD1>, - <MT2701_PIN_113_MSDC0_DAT5__FUNC_NLD5>, - <MT2701_PIN_115_MSDC0_RSTB__FUNC_NLD8>, - <MT2701_PIN_119_MSDC0_DAT2__FUNC_NLD2>; - input-enable; - drive-strength = <MTK_DRIVE_8mA>; - bias-pull-up; - }; - - pins_we { - pinmux = <MT2701_PIN_117_MSDC0_CLK__FUNC_NWEB>; - drive-strength = <MTK_DRIVE_8mA>; - bias-pull-up = <MTK_PUPD_SET_R1R0_10>; - }; - - pins_ale { - pinmux = <MT2701_PIN_116_MSDC0_CMD__FUNC_NALE>; - drive-strength = <MTK_DRIVE_8mA>; - bias-pull-down = <MTK_PUPD_SET_R1R0_10>; - }; - }; - }; - - &nandc { - status = "okay"; - pinctrl-names = "default"; - pinctrl-0 = <&nand_pins_default>; - nand@0 { - reg = <0>; - nand-on-flash-bbt; - nand-ecc-mode = "hw"; - nand-ecc-strength = <24>; - nand-ecc-step-size = <1024>; - }; - }; - -NAND chip optional subnodes: -- Partitions, see Documentation/devicetree/bindings/mtd/partition.txt - -Example: - nand@0 { - partitions { - compatible = "fixed-partitions"; - #address-cells = <1>; - #size-cells = <1>; - - preloader@0 { - label = "pl"; - read-only; - reg = <0x00000000 0x00400000>; - }; - android@00400000 { - label = "android"; - reg = <0x00400000 0x12c00000>; - }; - }; - }; - -2) ECC Engine: -============== - -Required BCH properties: -- compatible: Should be one of - "mediatek,mt2701-ecc", - "mediatek,mt2712-ecc", - "mediatek,mt7622-ecc". -- reg: Base physical address and size of ECC. -- interrupts: Interrupts of ECC. -- clocks: ECC required clocks. -- clock-names: ECC clocks internal name. - -Example: - - bch: ecc@1100e000 { - compatible = "mediatek,mt2701-ecc"; - reg = <0 0x1100e000 0 0x1000>; - interrupts = <GIC_SPI 55 IRQ_TYPE_LEVEL_LOW>; - clocks = <&pericfg CLK_PERI_NFI_ECC>; - clock-names = "nfiecc_clk"; - }; diff --git a/Documentation/devicetree/bindings/mtd/mtk-nand.yaml b/Documentation/devicetree/bindings/mtd/mtk-nand.yaml new file mode 100644 index 000000000000..47a1334bcddd --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/mtk-nand.yaml @@ -0,0 +1,92 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/mtd/mtk-nand.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: MediaTek(MTK) SoCs raw NAND FLASH controller (NFC) device tree bindings + +maintainers: + - Xiangsheng Hou <xiangsheng.hou@xxxxxxxxxxxx> + +allOf: + - $ref: "nand-controller.yaml#" + +properties: + compatible: + enum: + - mediatek,mt2701-nfc + - mediatek,mt2712-nfc + - mediatek,mt7622-nfc + + reg: + items: + - description: Base physical address and size of NFI. + + interrupts: + items: + - description: NFI interrupt + + clocks: + minItems: 2 + items: + - description: clock used for the controller + - description: clock used for the pad + + clock-names: + minItems: 2 + items: + - const: nfi_clk + - const: pad_clk + + nand-ecc-engine: + description: Required ECC Engine node + $ref: /schemas/types.yaml#/definitions/phandle + + "#address-cells": + const: 1 + + "#size-cells": + const: 0 + +required: + - compatible + - reg + - interrupts + - clocks + - clock-names + - nand-ecc-engine + - "#address-cells" + - "#size-cells" + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/clock/mt2701-clk.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/interrupt-controller/irq.h> + + soc { + #address-cells = <2>; + #size-cells = <2>; + + nandc: nfi@1100d000 { + compatible = "mediatek,mt2701-nfc"; + reg = <0 0x1100d000 0 0x1000>; + interrupts = <GIC_SPI 56 IRQ_TYPE_LEVEL_LOW>; + clocks = <&pericfg CLK_PERI_NFI>, + <&pericfg CLK_PERI_NFI_PAD>; + clock-names = "nfi_clk", "pad_clk"; + nand-ecc-engine = <&bch>; + #address-cells = <1>; + #size-cells = <0>; + }; + + bch: ecc@1100e000 { + compatible = "mediatek,mt2701-ecc"; + reg = <0 0x1100e000 0 0x1000>; + interrupts = <GIC_SPI 55 IRQ_TYPE_LEVEL_LOW>; + clocks = <&pericfg CLK_PERI_NFI_ECC>; + }; + }; -- 2.25.1
