Quoting Tomi Valkeinen (2022-11-17 12:25:43)
> From: Tomi Valkeinen <tomi.valkeinen+renesas@xxxxxxxxxxxxxxxx>
>
> Add DT nodes for components needed to get the DSI output working:
> - FCPv
> - VSPd
> - DU
> - DSI
>
> Signed-off-by: Tomi Valkeinen <tomi.valkeinen+renesas@xxxxxxxxxxxxxxxx>
> ---
> arch/arm64/boot/dts/renesas/r8a779g0.dtsi | 129 ++++++++++++++++++++++
> 1 file changed, 129 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/renesas/r8a779g0.dtsi b/arch/arm64/boot/dts/renesas/r8a779g0.dtsi
> index 45d8d927ad26..31d4930c5adc 100644
> --- a/arch/arm64/boot/dts/renesas/r8a779g0.dtsi
> +++ b/arch/arm64/boot/dts/renesas/r8a779g0.dtsi
> @@ -1207,6 +1207,135 @@ prr: chipid@fff00044 {
> compatible = "renesas,prr";
> reg = <0 0xfff00044 0 4>;
> };
I think these nodes are supposed to be in sort order based on the
register address in memory.
Disregarding sort order, I'll review the node contents.
I would probably s/data/nodes/ in $SUBJECT too.
> +
> + fcpvd0: fcp@fea10000 {
> + compatible = "renesas,fcpv";
> + reg = <0 0xfea10000 0 0x200>;
> + clocks = <&cpg CPG_MOD 508>;
> + power-domains = <&sysc R8A779G0_PD_ALWAYS_ON>;
> + resets = <&cpg 508>;
> + };
> +
> + fcpvd1: fcp@fea11000 {
> + compatible = "renesas,fcpv";
> + reg = <0 0xfea11000 0 0x200>;
> + clocks = <&cpg CPG_MOD 509>;
> + power-domains = <&sysc R8A779G0_PD_ALWAYS_ON>;
> + resets = <&cpg 509>;
> + };
I'm intrigued at the length of 0x200 as I only see 3 registers up to
0x0018 ..
But all existing platforms with fcpv* set 0x200 ... so lets cargo cult it up... :-)
> +
> + vspd0: vsp@fea20000 {
> + compatible = "renesas,vsp2";
> + reg = <0 0xfea20000 0 0x5000>;
"""
Below are the base addresses of each VSP unit. VSPX has 32Kbyte address
space. VSPD has 28Kbyte address space.
"""
Hrm : 28K is 0x7000
RPf n OSD CLUT Table: H’4000 + H’0400*n to H’43fc + H’0400*n
0x43fc+(0x400*5)
22524 [0x57fc]
So this needs to be /at least/ 0x6000 (Would 0x5800 be odd?) and perhaps as it clearly states
28k, we should just set it to 0x7000.
> + interrupts = <GIC_SPI 546 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&cpg CPG_MOD 830>;
> + power-domains = <&sysc R8A779G0_PD_ALWAYS_ON>;
> + resets = <&cpg 830>;
> +
> + renesas,fcp = <&fcpvd0>;
> + };
> +
> + vspd1: vsp@fea28000 {
> + compatible = "renesas,vsp2";
> + reg = <0 0xfea28000 0 0x5000>;
Same here of course (reg = <0 0xfea28000 0 0x7000>)
> + interrupts = <GIC_SPI 551 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&cpg CPG_MOD 831>;
> + power-domains = <&sysc R8A779G0_PD_ALWAYS_ON>;
> + resets = <&cpg 831>;
> +
> + renesas,fcp = <&fcpvd1>;
> + };
> +
> + du: display@feb00000 {
> + compatible = "renesas,du-r8a779g0";
> + reg = <0 0xfeb00000 0 0x40000>;
> + interrupts = <GIC_SPI 523 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 524 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&cpg CPG_MOD 411>;
> + clock-names = "du.0";
> + power-domains = <&sysc R8A779G0_PD_ALWAYS_ON>;
> + resets = <&cpg 411>;
> + reset-names = "du.0";
> + renesas,vsps = <&vspd0 0>, <&vspd1 0>;
> +
> + status = "disabled";
> +
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + port@0 {
> + reg = <0>;
> + du_out_dsi0: endpoint {
> + remote-endpoint = <&dsi0_in>;
> + };
> + };
> +
> + port@1 {
> + reg = <1>;
> + du_out_dsi1: endpoint {
> + remote-endpoint = <&dsi1_in>;
> + };
> + };
> + };
> + };
> +
> + dsi0: dsi-encoder@fed80000 {
> + compatible = "renesas,r8a779g0-dsi-csi2-tx";
> + reg = <0 0xfed80000 0 0x10000>;
> + power-domains = <&sysc R8A779G0_PD_ALWAYS_ON>;
> + clocks = <&cpg CPG_MOD 415>,
> + <&cpg CPG_CORE R8A779G0_CLK_DSIEXT>,
> + <&cpg CPG_CORE R8A779G0_CLK_DSIREF>;
> + clock-names = "fck", "dsi", "pll";
> + resets = <&cpg 415>;
blank line here to separate it, and highlight that it's disabled? (Like
is done for DU?
> + status = "disabled";
> +
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + port@0 {
> + reg = <0>;
> + dsi0_in: endpoint {
> + remote-endpoint = <&du_out_dsi0>;
> + };
> + };
> +
> + port@1 {
> + reg = <1>;
> + };
> + };
> + };
> +
> + dsi1: dsi-encoder@fed90000 {
> + compatible = "renesas,r8a779g0-dsi-csi2-tx";
> + reg = <0 0xfed90000 0 0x10000>;
> + power-domains = <&sysc R8A779G0_PD_ALWAYS_ON>;
> + clocks = <&cpg CPG_MOD 416>,
> + <&cpg CPG_CORE R8A779G0_CLK_DSIEXT>,
> + <&cpg CPG_CORE R8A779G0_CLK_DSIREF>;
> + clock-names = "fck", "dsi", "pll";
> + resets = <&cpg 416>;
Same.
With the VSPD register ranges increased accordingly:
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@xxxxxxxxxxxxxxxx>
> + status = "disabled";
> +
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + port@0 {
> + reg = <0>;
> + dsi1_in: endpoint {
> + remote-endpoint = <&du_out_dsi1>;
> + };
> + };
> +
> + port@1 {
> + reg = <1>;
> + };
> + };
> + };
> +
> };
>
> timer {
> --
> 2.34.1
>
