Sony ever so graciously provides GPIO line names in their downstream
kernel (though sometimes they are not 100% accurate and you can judge
that by simply looking at them and with what drivers they are used).
Add these to the PDX223&224 DTSIs to better document the hardware.
Diff between 223 and 224:
< gpio-line-names = "NC", /* GPIO_0 */
< "NC",
< "NC",
< "NC",
> gpio-line-names = "TELE_SPI_MISO", /* GPIO_0 */
> "TELE_SPI_MOSI",
> "TELE_SPI_CLK",
> "TELE_SPI_CS_N",
< "PM8010_2_RESET_N",
> "NC",
< "NC",
> "UWIDEC_PWR_EN",
< "TOF_RST_N",
> "NC"
< "QLINK1_REQ",
< "QLINK1_EN", /* GPIO_160 */
< "QLINK1_WMSS_RESET_N",
> "NC",
> "NC", /* GPIO_160 */
> "NC",
The tele lens setup is different on 1 IV and 5 IV and power wiring
is different for some lenses, so it makes sense. As for QLINK, no
idea.
Signed-off-by: Konrad Dybcio <konrad.dybcio@xxxxxxxxxx>
---
.../qcom/sm8450-sony-xperia-nagara-pdx223.dts | 213 ++++++++++++++++++
.../qcom/sm8450-sony-xperia-nagara-pdx224.dts | 213 ++++++++++++++++++
2 files changed, 426 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/sm8450-sony-xperia-nagara-pdx223.dts b/arch/arm64/boot/dts/qcom/sm8450-sony-xperia-nagara-pdx223.dts
index 3ab145877094..b83500316a81 100644
--- a/arch/arm64/boot/dts/qcom/sm8450-sony-xperia-nagara-pdx223.dts
+++ b/arch/arm64/boot/dts/qcom/sm8450-sony-xperia-nagara-pdx223.dts
@@ -12,3 +12,216 @@ / {
model = "Sony Xperia 1 IV";
compatible = "sony,pdx223", "qcom,sm8450";
};
+
+&tlmm {
+ gpio-line-names = "NC", /* GPIO_0 */
+ "NC",
+ "NC",
+ "NC",
+ "WLC_I2C_SDA",
+ "WLC_I2C_SCL",
+ "NC",
+ "PM8010_1_RESET_N",
+ "WLC_INT_N",
+ "NC",
+ "NC", /* GPIO_10 */
+ "PM8010_2_RESET_N",
+ "DISP_ERR_FG",
+ "HALL_INT_N",
+ "ALS_PROX_INT_N",
+ "IMU1_INT",
+ "TS_I2C_SDA",
+ "TS_I2C_SCL",
+ "DISP_RESET_N",
+ "DISP_VDDR_EN",
+ "TS_RESET_N", /* GPIO_20 */
+ "TS_INT_N",
+ "NC",
+ "TELEC_PWR_EN",
+ "CAM1_RESET_N",
+ "LEO_CAM0_RESET_N",
+ "DEBUG_UART_TX",
+ "DEBUG_UART_RX",
+ "FP_SPI_MISO",
+ "FP_SPI_MOSI",
+ "FP_SPI_CLK", /* GPIO_30 */
+ "FP_SPI_CS_N",
+ "NFC_I2C_SDA",
+ "NFC_I2C_SCL",
+ "NFC_EN",
+ "NFC_CLK_REQ",
+ "NFC_ESE_SPI_MISO",
+ "NFC_ESE_SPI_MOSI",
+ "NFC_ESE_SPI_CLK",
+ "NFC_ESE_SPI_CS",
+ "FP_INT_N", /* GPIO_40 */
+ "NC",
+ "FP_RESET_N",
+ "WCD_RST_N",
+ "NC",
+ "NFC_DWL_REQ",
+ "NFC_IRQ",
+ "FORCE_USB_BOOT",
+ "APPS_I2C_1_SDA",
+ "APPS_I2C_1_SCL",
+ "SBU_SW_OE", /* GPIO_50 */
+ "SBU_SW_SEL",
+ "SPK_AMP_I2C_SDA",
+ "SPK_AMP_I2C_SCL",
+ "NC",
+ "NC",
+ "CAMSENSOR_I2C_SDA",
+ "CAMSENSOR_I2C_SCL",
+ "GNSS_ELNA_EN0",
+ "NC",
+ "NC", /* GPIO_60 */
+ "NC",
+ "NC",
+ "NC",
+ "NC",
+ "NC",
+ "RGBC_IR_INT",
+ "NC",
+ "NC",
+ "NC",
+ "NC", /* GPIO_70 */
+ "NC",
+ "HAP_I2C_SDA",
+ "HAP_I2C_SCL",
+ "HAP_RST_N",
+ "HAP_INT_N",
+ "HST_BT_UART_CTS",
+ "HST_BT_UART_RFR",
+ "HST_BT_UART_TX",
+ "HST_BT_UART_RX",
+ "HST_WLAN_EN", /* GPIO_80 */
+ "HST_BT_EN",
+ "HST_SW_CTRL",
+ "NC",
+ "NC",
+ "NC",
+ "DISP_VSYNC",
+ "NC",
+ "NC",
+ "HW_ID_0",
+ "HW_ID_1", /* GPIO_90 */
+ "USB_CC_DIR",
+ "TRAY_DET",
+ "SW_SERVICE",
+ "PCIE0_RESET_N",
+ "PCIE0_CLK_REQ_N",
+ "PCIE0_WAKE_N",
+ "OIS_ENABLE_WIDE",
+ "DEBUG_GPIO0",
+ "NC",
+ "CAM_MCLK0", /* GPIO_100 */
+ "CAM_MCLK1",
+ "CAM_MCLK2",
+ "CAM_MCLK3",
+ "NC",
+ "NC",
+ "TOF_RST_N",
+ "CAM_SOF",
+ "NC",
+ "AFEXPTMG_TELE",
+ "CCI_I2C0_SDA", /* GPIO_110 */
+ "CCI_I2C0_SCL",
+ "CCI_I2C1_SDA",
+ "CCI_I2C1_SCL",
+ "CCI_I2C2_SDA",
+ "CCI_I2C2_SCL",
+ "NC",
+ "CAM2_RESET_N",
+ "NC",
+ "EXT_VD0_XVS",
+ "CAM3_RESET_N", /* GPIO_120 */
+ "NC",
+ "NC",
+ "NC",
+ "NC",
+ "RF_ID_EXTENSION_2",
+ "HAP_I2S_CLK",
+ "HAP_I2S_DOUT",
+ "HAP_TRG1",
+ "HAP_I2S_SYNC",
+ "UIM1_DATA", /* GPIO_130 */
+ "UIM1_CLK",
+ "UIM1_RESET",
+ "TRAY_DET",
+ "UIM2_DATA",
+ "UIM2_CLK",
+ "UIM2_RESET",
+ "UIM2_PRESENT",
+ "SM_RFFE0_CLK",
+ "SM_RFFE0_DATA",
+ "SM_RFFE1_CLK", /* GPIO_140 */
+ "SM_RFFE1_DATA",
+ "SM_MSS_GRFC4",
+ "HST_AS_EN",
+ "LAA_RX_EN",
+ "NC",
+ "SM_RFFE4_CLK",
+ "SM_RFFE4_DATA",
+ "WLAN_COEX_UART1_RX",
+ "WLAN_COEX_UART1_TX",
+ "RF_LCD_ID_EN", /* GPIO_150 */
+ "RF_ID_EXTENSION",
+ "SM_MSS_GRFC12",
+ "NFC_COLD_RST",
+ "NC",
+ "NC",
+ "SDR1_QLINK0_REQ",
+ "SDR1_QLINK0_EN",
+ "SDR1_QLINK0_WMSS_RESET_N",
+ "QLINK1_REQ",
+ "QLINK1_EN", /* GPIO_160 */
+ "QLINK1_WMSS_RESET_N",
+ "SDR2_QLINK2_REQ",
+ "SDR2_QLINK2_EN",
+ "SDR2_QLINK2_WMSS_RESET_N",
+ "WCD_SWR_TX_CLK",
+ "WCD_SWR_TX_DATA0",
+ "WCD_SWR_TX_DATA1",
+ "WCD_SWR_RX_CLK",
+ "WCD_SWR_RX_DATA0",
+ "WCD_SWR_RX_DATA1", /* GPIO_170 */
+ "SM_DMIC1_CLK",
+ "SM_DMIC1_DATA",
+ "SM_DMIC2_CLK",
+ "SM_DMIC2_DATA",
+ "SPK_AMP_I2S_CLK",
+ "SPK_AMP_I2S_WS",
+ "NC",
+ "NC",
+ "WCD_SWR_TX_DATA2",
+ "SPK_AMP_I2S_ASP_DIN", /* GPIO_180 */
+ "SPK_AMP_I2S_ASP_DOUT",
+ "SPK_AMP_INT_N",
+ "SPK_AMP_RESET_N",
+ "HST_BT_WLAN_SLIMBUS_CLK",
+ "HST_BT_WLAN_SLIMBUS_DAT0",
+ "NC",
+ "NC",
+ "NC",
+ "NC",
+ "MAG_I2C_SDA", /* GPIO_190 */
+ "MAG_I2C_SCL",
+ "IMU_SPI_MISO",
+ "IMU_SPI_MOSI",
+ "IMU_SPI_CLK",
+ "IMU_SPI_CS_N",
+ "SENSOR_I2C_SDA",
+ "SENSOR_I2C_SCL",
+ "OIS_TELE_I2C_SDA",
+ "OIS_TELE_I2C_SCL",
+ "NC", /* GPIO_200 */
+ "OIS_ENABLE_TELE",
+ "HST_BLE_UART_TX",
+ "HST_BLE_UART_RX",
+ "HSTP_CLK_CFG_SEL",
+ "NC",
+ "APPS_I2C_0_SDA",
+ "APPS_I2C_0_SCL",
+ "CCI_I2C3_SDA",
+ "CCI_I2C3_SCL";
+};
diff --git a/arch/arm64/boot/dts/qcom/sm8450-sony-xperia-nagara-pdx224.dts b/arch/arm64/boot/dts/qcom/sm8450-sony-xperia-nagara-pdx224.dts
index 0d64d3c0afed..13c2fc4bccfc 100644
--- a/arch/arm64/boot/dts/qcom/sm8450-sony-xperia-nagara-pdx224.dts
+++ b/arch/arm64/boot/dts/qcom/sm8450-sony-xperia-nagara-pdx224.dts
@@ -19,3 +19,216 @@ imx563_vdig_vreg: imx563-vdig-regulator {
enable-active-high;
};
};
+
+&tlmm {
+ gpio-line-names = "TELE_SPI_MISO", /* GPIO_0 */
+ "TELE_SPI_MOSI", /* SONY says NC, but it only makes sense this way.. */
+ "TELE_SPI_CLK",
+ "TELE_SPI_CS_N",
+ "WLC_I2C_SDA",
+ "WLC_I2C_SCL",
+ "NC",
+ "PM8010_1_RESET_N",
+ "WLC_INT_N",
+ "NC",
+ "NC", /* GPIO_10 */
+ "NC",
+ "DISP_ERR_FG",
+ "HALL_INT_N",
+ "ALS_PROX_INT_N",
+ "IMU1_INT",
+ "TS_I2C_SDA",
+ "TS_I2C_SCL",
+ "DISP_RESET_N",
+ "DISP_VDDR_EN",
+ "TS_RESET_N", /* GPIO_20 */
+ "TS_INT_N",
+ "UWIDEC_PWR_EN",
+ "TELEC_PWR_EN",
+ "CAM1_RESET_N",
+ "LEO_CAM0_RESET_N",
+ "DEBUG_UART_TX",
+ "DEBUG_UART_RX",
+ "FP_SPI_MISO",
+ "FP_SPI_MOSI",
+ "FP_SPI_CLK", /* GPIO_30 */
+ "FP_SPI_CS_N",
+ "NFC_I2C_SDA",
+ "NFC_I2C_SCL",
+ "NFC_EN",
+ "NFC_CLK_REQ",
+ "NFC_ESE_SPI_MISO",
+ "NFC_ESE_SPI_MOSI",
+ "NFC_ESE_SPI_CLK",
+ "NFC_ESE_SPI_CS",
+ "FP_INT_N", /* GPIO_40 */
+ "NC",
+ "FP_RESET_N",
+ "WCD_RST_N",
+ "NC",
+ "NFC_DWL_REQ",
+ "NFC_IRQ",
+ "FORCE_USB_BOOT",
+ "APPS_I2C_1_SDA",
+ "APPS_I2C_1_SCL",
+ "SBU_SW_OE", /* GPIO_50 */
+ "SBU_SW_SEL",
+ "SPK_AMP_I2C_SDA",
+ "SPK_AMP_I2C_SCL",
+ "NC",
+ "NC",
+ "CAMSENSOR_I2C_SDA",
+ "CAMSENSOR_I2C_SCL",
+ "GNSS_ELNA_EN0",
+ "NC",
+ "NC", /* GPIO_60 */
+ "NC",
+ "NC",
+ "NC",
+ "NC",
+ "NC",
+ "RGBC_IR_INT",
+ "NC",
+ "NC",
+ "NC",
+ "NC", /* GPIO_70 */
+ "NC",
+ "HAP_I2C_SDA",
+ "HAP_I2C_SCL",
+ "HAP_RST_N",
+ "HAP_INT_N",
+ "HST_BT_UART_CTS",
+ "HST_BT_UART_RFR",
+ "HST_BT_UART_TX",
+ "HST_BT_UART_RX",
+ "HST_WLAN_EN", /* GPIO_80 */
+ "HST_BT_EN",
+ "HST_SW_CTRL",
+ "NC",
+ "NC",
+ "NC",
+ "DISP_VSYNC",
+ "NC",
+ "NC",
+ "HW_ID_0",
+ "HW_ID_1", /* GPIO_90 */
+ "USB_CC_DIR",
+ "TRAY_DET",
+ "SW_SERVICE",
+ "PCIE0_RESET_N",
+ "PCIE0_CLK_REQ_N",
+ "PCIE0_WAKE_N",
+ "OIS_ENABLE_WIDE",
+ "DEBUG_GPIO0",
+ "NC",
+ "CAM_MCLK0", /* GPIO_100 */
+ "CAM_MCLK1",
+ "CAM_MCLK2",
+ "CAM_MCLK3",
+ "NC",
+ "NC",
+ "NC", /* SONY didn't rename this, but there's no ToF so it's likely NC */
+ "CAM_SOF",
+ "NC",
+ "AFEXPTMG_TELE",
+ "CCI_I2C0_SDA", /* GPIO_110 */
+ "CCI_I2C0_SCL",
+ "CCI_I2C1_SDA",
+ "CCI_I2C1_SCL",
+ "CCI_I2C2_SDA",
+ "CCI_I2C2_SCL",
+ "NC",
+ "CAM2_RESET_N",
+ "NC",
+ "EXT_VD0_XVS",
+ "CAM3_RESET_N", /* GPIO_120 */
+ "NC",
+ "NC",
+ "NC",
+ "NC",
+ "RF_ID_EXTENSION_2",
+ "HAP_I2S_CLK",
+ "HAP_I2S_DOUT",
+ "HAP_TRG1",
+ "HAP_I2S_SYNC",
+ "UIM1_DATA", /* GPIO_130 */
+ "UIM1_CLK",
+ "UIM1_RESET",
+ "TRAY_DET",
+ "UIM2_DATA",
+ "UIM2_CLK",
+ "UIM2_RESET",
+ "UIM2_PRESENT",
+ "SM_RFFE0_CLK",
+ "SM_RFFE0_DATA",
+ "SM_RFFE1_CLK", /* GPIO_140 */
+ "SM_RFFE1_DATA",
+ "SM_MSS_GRFC4",
+ "HST_AS_EN",
+ "LAA_RX_EN",
+ "NC",
+ "SM_RFFE4_CLK",
+ "SM_RFFE4_DATA",
+ "WLAN_COEX_UART1_RX",
+ "WLAN_COEX_UART1_TX",
+ "RF_LCD_ID_EN", /* GPIO_150 */
+ "RF_ID_EXTENSION",
+ "SM_MSS_GRFC12",
+ "NFC_COLD_RST",
+ "NC",
+ "NC",
+ "SDR1_QLINK0_REQ",
+ "SDR1_QLINK0_EN",
+ "SDR1_QLINK0_WMSS_RESET_N",
+ "NC",
+ "NC", /* GPIO_160 */
+ "NC",
+ "SDR2_QLINK2_REQ",
+ "SDR2_QLINK2_EN",
+ "SDR2_QLINK2_WMSS_RESET_N",
+ "WCD_SWR_TX_CLK",
+ "WCD_SWR_TX_DATA0",
+ "WCD_SWR_TX_DATA1",
+ "WCD_SWR_RX_CLK",
+ "WCD_SWR_RX_DATA0",
+ "WCD_SWR_RX_DATA1", /* GPIO_170 */
+ "SM_DMIC1_CLK",
+ "SM_DMIC1_DATA",
+ "SM_DMIC2_CLK",
+ "SM_DMIC2_DATA",
+ "SPK_AMP_I2S_CLK",
+ "SPK_AMP_I2S_WS",
+ "NC",
+ "NC",
+ "WCD_SWR_TX_DATA2",
+ "SPK_AMP_I2S_ASP_DIN", /* GPIO_180 */
+ "SPK_AMP_I2S_ASP_DOUT",
+ "SPK_AMP_INT_N",
+ "SPK_AMP_RESET_N",
+ "HST_BT_WLAN_SLIMBUS_CLK",
+ "HST_BT_WLAN_SLIMBUS_DAT0",
+ "NC",
+ "NC",
+ "NC",
+ "NC",
+ "MAG_I2C_SDA", /* GPIO_190 */
+ "MAG_I2C_SCL",
+ "IMU_SPI_MISO",
+ "IMU_SPI_MOSI",
+ "IMU_SPI_CLK",
+ "IMU_SPI_CS_N",
+ "SENSOR_I2C_SDA",
+ "SENSOR_I2C_SCL",
+ "OIS_TELE_I2C_SDA",
+ "OIS_TELE_I2C_SCL",
+ "NC", /* GPIO_200 */
+ "OIS_ENABLE_TELE",
+ "HST_BLE_UART_TX",
+ "HST_BLE_UART_RX",
+ "HSTP_CLK_CFG_SEL",
+ "NC",
+ "APPS_I2C_0_SDA",
+ "APPS_I2C_0_SCL",
+ "CCI_I2C3_SDA",
+ "CCI_I2C3_SCL";
+};
--
2.38.1
