Baikal-T1 SoC is equipped with DWC PCIe v4.60a host controller. It can be
trained to work up to Gen.3 speed over up to x4 lanes. The host controller
is attached to the DW PCIe 3.0 PCS via the PIPE-4 interface, which in its
turn is connected to the DWC 10G PHY. The whole system is supposed to be
fed up with four clock sources: DBI peripheral clock, AXI application
clocks and external PHY/core reference clock generating the 100MHz signal.
In addition to that the platform provide a way to reset each part of the
controller: sticky/non-sticky bits, host controller core, PIPE interface,
PCS/PHY and Hot/Power reset signal. The driver also provides a way to
handle the GPIO-based PERST# signal.
Note due to the Baikal-T1 MMIO peculiarity we have to implement the DBI
interface accessors which make sure the IO operations are dword-aligned.
Signed-off-by: Serge Semin <Sergey.Semin@xxxxxxxxxxxxxxxxxxxx>
---
Changelog v2:
- Rename 'syscon' property to 'baikal,bt1-syscon'.
Changelog v3:
- Use the clocks/resets handlers defined in the DW PCIe core descriptor.
(@Rob)
- Redefine PCI host bridge config space accessors with the generic
pci_generic_config_read32() and pci_generic_config_write32() methods.
(@Rob)
Changelog v4:
- Drop PCIBIOS_* macros usage. (@Rob)
- Add "static const" to the dw_pcie_ops and dw_pcie_host_ops structure
instances. (@Bjorn)
- Rename bt1_pcie_dw_ops to bt1_pcie_ops. (@Bjorn)
- Rename bt1_pcie_ops to bt1_pci_ops. (@Bjorn)
- Use start_link/stop_link suffixes in the corresponding callbacks.
(@Bjorn)
- Change the get_res() method suffix to being get_resources(). (@Bjorn)
- Change *_{add,del}_dw_port() method to *_{add,del}_port(). (@Bjorn)
- Drop dma_coerce_mask_and_coherent() applied to the PCI host bridge
kernel device instance. (@Bjorn)
- Add the comment above the dma_set_mask_and_coherent() method usage
regarding the controller eDMA feature. (@Bjorn)
- Fix the comment above the core reset controls assertion. (@Bjorn)
- Replace delays and timeout numeric literals with macros. (@Bjorn)
Changelog v6:
- Move the DMA-mask setup to the eDMA driver. (@Robin)
---
drivers/pci/controller/dwc/Kconfig | 9 +
drivers/pci/controller/dwc/Makefile | 1 +
drivers/pci/controller/dwc/pcie-bt1.c | 645 ++++++++++++++++++++++++++
3 files changed, 655 insertions(+)
create mode 100644 drivers/pci/controller/dwc/pcie-bt1.c
diff --git a/drivers/pci/controller/dwc/Kconfig b/drivers/pci/controller/dwc/Kconfig
index 62ce3abf0f19..771b8b146623 100644
--- a/drivers/pci/controller/dwc/Kconfig
+++ b/drivers/pci/controller/dwc/Kconfig
@@ -222,6 +222,15 @@ config PCIE_ARTPEC6_EP
Enables support for the PCIe controller in the ARTPEC-6 SoC to work in
endpoint mode. This uses the DesignWare core.
+config PCIE_BT1
+ tristate "Baikal-T1 PCIe controller"
+ depends on MIPS_BAIKAL_T1 || COMPILE_TEST
+ depends on PCI_MSI_IRQ_DOMAIN
+ select PCIE_DW_HOST
+ help
+ Enables support for the PCIe controller in the Baikal-T1 SoC to work
+ in host mode. It's based on the Synopsys DWC PCIe v4.60a IP-core.
+
config PCIE_ROCKCHIP_DW_HOST
bool "Rockchip DesignWare PCIe controller"
select PCIE_DW
diff --git a/drivers/pci/controller/dwc/Makefile b/drivers/pci/controller/dwc/Makefile
index 8ba7b67f5e50..bf5c311875a1 100644
--- a/drivers/pci/controller/dwc/Makefile
+++ b/drivers/pci/controller/dwc/Makefile
@@ -3,6 +3,7 @@ obj-$(CONFIG_PCIE_DW) += pcie-designware.o
obj-$(CONFIG_PCIE_DW_HOST) += pcie-designware-host.o
obj-$(CONFIG_PCIE_DW_EP) += pcie-designware-ep.o
obj-$(CONFIG_PCIE_DW_PLAT) += pcie-designware-plat.o
+obj-$(CONFIG_PCIE_BT1) += pcie-bt1.o
obj-$(CONFIG_PCI_DRA7XX) += pci-dra7xx.o
obj-$(CONFIG_PCI_EXYNOS) += pci-exynos.o
obj-$(CONFIG_PCIE_FU740) += pcie-fu740.o
diff --git a/drivers/pci/controller/dwc/pcie-bt1.c b/drivers/pci/controller/dwc/pcie-bt1.c
new file mode 100644
index 000000000000..babbbf675a28
--- /dev/null
+++ b/drivers/pci/controller/dwc/pcie-bt1.c
@@ -0,0 +1,645 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (C) 2021 BAIKAL ELECTRONICS, JSC
+ *
+ * Authors:
+ * Vadim Vlasov <Vadim.Vlasov@xxxxxxxxxxxxxxxxxxxx>
+ * Serge Semin <Sergey.Semin@xxxxxxxxxxxxxxxxxxxx>
+ *
+ * Baikal-T1 PCIe controller driver
+ */
+
+#include <linux/bitfield.h>
+#include <linux/bits.h>
+#include <linux/clk.h>
+#include <linux/delay.h>
+#include <linux/gpio/consumer.h>
+#include <linux/kernel.h>
+#include <linux/mfd/syscon.h>
+#include <linux/module.h>
+#include <linux/pci.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+#include <linux/reset.h>
+#include <linux/types.h>
+
+#include "pcie-designware.h"
+
+/* Baikal-T1 System CCU control registers */
+#define BT1_CCU_PCIE_CLKC 0x140
+#define BT1_CCU_PCIE_REQ_PCS_CLK BIT(16)
+#define BT1_CCU_PCIE_REQ_MAC_CLK BIT(17)
+#define BT1_CCU_PCIE_REQ_PIPE_CLK BIT(18)
+
+#define BT1_CCU_PCIE_RSTC 0x144
+#define BT1_CCU_PCIE_REQ_LINK_RST BIT(13)
+#define BT1_CCU_PCIE_REQ_SMLH_RST BIT(14)
+#define BT1_CCU_PCIE_REQ_PHY_RST BIT(16)
+#define BT1_CCU_PCIE_REQ_CORE_RST BIT(24)
+#define BT1_CCU_PCIE_REQ_STICKY_RST BIT(26)
+#define BT1_CCU_PCIE_REQ_NSTICKY_RST BIT(27)
+
+#define BT1_CCU_PCIE_PMSC 0x148
+#define BT1_CCU_PCIE_LTSSM_STATE_MASK GENMASK(5, 0)
+#define BT1_CCU_PCIE_LTSSM_DET_QUIET 0x00
+#define BT1_CCU_PCIE_LTSSM_DET_ACT 0x01
+#define BT1_CCU_PCIE_LTSSM_POLL_ACT 0x02
+#define BT1_CCU_PCIE_LTSSM_POLL_COMP 0x03
+#define BT1_CCU_PCIE_LTSSM_POLL_CONF 0x04
+#define BT1_CCU_PCIE_LTSSM_PRE_DET_QUIET 0x05
+#define BT1_CCU_PCIE_LTSSM_DET_WAIT 0x06
+#define BT1_CCU_PCIE_LTSSM_CFG_LNKWD_START 0x07
+#define BT1_CCU_PCIE_LTSSM_CFG_LNKWD_ACEPT 0x08
+#define BT1_CCU_PCIE_LTSSM_CFG_LNNUM_WAIT 0x09
+#define BT1_CCU_PCIE_LTSSM_CFG_LNNUM_ACEPT 0x0a
+#define BT1_CCU_PCIE_LTSSM_CFG_COMPLETE 0x0b
+#define BT1_CCU_PCIE_LTSSM_CFG_IDLE 0x0c
+#define BT1_CCU_PCIE_LTSSM_RCVR_LOCK 0x0d
+#define BT1_CCU_PCIE_LTSSM_RCVR_SPEED 0x0e
+#define BT1_CCU_PCIE_LTSSM_RCVR_RCVRCFG 0x0f
+#define BT1_CCU_PCIE_LTSSM_RCVR_IDLE 0x10
+#define BT1_CCU_PCIE_LTSSM_L0 0x11
+#define BT1_CCU_PCIE_LTSSM_L0S 0x12
+#define BT1_CCU_PCIE_LTSSM_L123_SEND_IDLE 0x13
+#define BT1_CCU_PCIE_LTSSM_L1_IDLE 0x14
+#define BT1_CCU_PCIE_LTSSM_L2_IDLE 0x15
+#define BT1_CCU_PCIE_LTSSM_L2_WAKE 0x16
+#define BT1_CCU_PCIE_LTSSM_DIS_ENTRY 0x17
+#define BT1_CCU_PCIE_LTSSM_DIS_IDLE 0x18
+#define BT1_CCU_PCIE_LTSSM_DISABLE 0x19
+#define BT1_CCU_PCIE_LTSSM_LPBK_ENTRY 0x1a
+#define BT1_CCU_PCIE_LTSSM_LPBK_ACTIVE 0x1b
+#define BT1_CCU_PCIE_LTSSM_LPBK_EXIT 0x1c
+#define BT1_CCU_PCIE_LTSSM_LPBK_EXIT_TOUT 0x1d
+#define BT1_CCU_PCIE_LTSSM_HOT_RST_ENTRY 0x1e
+#define BT1_CCU_PCIE_LTSSM_HOT_RST 0x1f
+#define BT1_CCU_PCIE_LTSSM_RCVR_EQ0 0x20
+#define BT1_CCU_PCIE_LTSSM_RCVR_EQ1 0x21
+#define BT1_CCU_PCIE_LTSSM_RCVR_EQ2 0x22
+#define BT1_CCU_PCIE_LTSSM_RCVR_EQ3 0x23
+#define BT1_CCU_PCIE_SMLH_LINKUP BIT(6)
+#define BT1_CCU_PCIE_RDLH_LINKUP BIT(7)
+#define BT1_CCU_PCIE_PM_LINKSTATE_L0S BIT(8)
+#define BT1_CCU_PCIE_PM_LINKSTATE_L1 BIT(9)
+#define BT1_CCU_PCIE_PM_LINKSTATE_L2 BIT(10)
+#define BT1_CCU_PCIE_L1_PENDING BIT(12)
+#define BT1_CCU_PCIE_REQ_EXIT_L1 BIT(14)
+#define BT1_CCU_PCIE_LTSSM_RCVR_EQ BIT(15)
+#define BT1_CCU_PCIE_PM_DSTAT_MASK GENMASK(18, 16)
+#define BT1_CCU_PCIE_PM_PME_EN BIT(20)
+#define BT1_CCU_PCIE_PM_PME_STATUS BIT(21)
+#define BT1_CCU_PCIE_AUX_PM_EN BIT(22)
+#define BT1_CCU_PCIE_AUX_PWR_DET BIT(23)
+#define BT1_CCU_PCIE_WAKE_DET BIT(24)
+#define BT1_CCU_PCIE_TURNOFF_REQ BIT(30)
+#define BT1_CCU_PCIE_TURNOFF_ACK BIT(31)
+
+#define BT1_CCU_PCIE_GENC 0x14c
+#define BT1_CCU_PCIE_LTSSM_EN BIT(1)
+#define BT1_CCU_PCIE_DBI2_MODE BIT(2)
+#define BT1_CCU_PCIE_MGMT_EN BIT(3)
+#define BT1_CCU_PCIE_RXLANE_FLIP_EN BIT(16)
+#define BT1_CCU_PCIE_TXLANE_FLIP_EN BIT(17)
+#define BT1_CCU_PCIE_SLV_XFER_PEND BIT(24)
+#define BT1_CCU_PCIE_RCV_XFER_PEND BIT(25)
+#define BT1_CCU_PCIE_DBI_XFER_PEND BIT(26)
+#define BT1_CCU_PCIE_DMA_XFER_PEND BIT(27)
+
+#define BT1_CCU_PCIE_LTSSM_LINKUP(_pmsc) \
+({ \
+ int __state = FIELD_GET(BT1_CCU_PCIE_LTSSM_STATE_MASK, _pmsc); \
+ __state >= BT1_CCU_PCIE_LTSSM_L0 && __state <= BT1_CCU_PCIE_LTSSM_L2_WAKE; \
+})
+
+/* Baikal-T1 PCIe specific control registers */
+#define BT1_PCIE_AXI2MGM_LANENUM 0xd04
+#define BT1_PCIE_AXI2MGM_LANESEL_MASK GENMASK(3, 0)
+
+#define BT1_PCIE_AXI2MGM_ADDRCTL 0xd08
+#define BT1_PCIE_AXI2MGM_PHYREG_ADDR_MASK GENMASK(20, 0)
+#define BT1_PCIE_AXI2MGM_READ_FLAG BIT(29)
+#define BT1_PCIE_AXI2MGM_DONE BIT(30)
+#define BT1_PCIE_AXI2MGM_BUSY BIT(31)
+
+#define BT1_PCIE_AXI2MGM_WRITEDATA 0xd0c
+#define BT1_PCIE_AXI2MGM_WDATA GENMASK(15, 0)
+
+#define BT1_PCIE_AXI2MGM_READDATA 0xd10
+#define BT1_PCIE_AXI2MGM_RDATA GENMASK(15, 0)
+
+/* Generic Baikal-T1 PCIe interface resources */
+#define BT1_PCIE_NUM_APP_CLKS ARRAY_SIZE(bt1_pcie_app_clks)
+#define BT1_PCIE_NUM_CORE_CLKS ARRAY_SIZE(bt1_pcie_core_clks)
+#define BT1_PCIE_NUM_APP_RSTS ARRAY_SIZE(bt1_pcie_app_rsts)
+#define BT1_PCIE_NUM_CORE_RSTS ARRAY_SIZE(bt1_pcie_core_rsts)
+
+/* PCIe bus setup delays and timeouts */
+#define BT1_PCIE_RST_DELAY_MS 100
+#define BT1_PCIE_RUN_DELAY_US 100
+#define BT1_PCIE_REQ_DELAY_US 1
+#define BT1_PCIE_REQ_TIMEOUT_US 1000
+#define BT1_PCIE_LNK_DELAY_US 1000
+#define BT1_PCIE_LNK_TIMEOUT_US 1000000
+
+static const enum dw_pcie_app_clk bt1_pcie_app_clks[] = {
+ DW_PCIE_DBI_CLK, DW_PCIE_MSTR_CLK, DW_PCIE_SLV_CLK,
+};
+
+static const enum dw_pcie_core_clk bt1_pcie_core_clks[] = {
+ DW_PCIE_REF_CLK,
+};
+
+static const enum dw_pcie_app_rst bt1_pcie_app_rsts[] = {
+ DW_PCIE_MSTR_RST, DW_PCIE_SLV_RST,
+};
+
+static const enum dw_pcie_core_rst bt1_pcie_core_rsts[] = {
+ DW_PCIE_NON_STICKY_RST, DW_PCIE_STICKY_RST, DW_PCIE_CORE_RST,
+ DW_PCIE_PIPE_RST, DW_PCIE_PHY_RST, DW_PCIE_HOT_RST, DW_PCIE_PWR_RST,
+};
+
+struct bt1_pcie {
+ struct dw_pcie dw;
+ struct platform_device *pdev;
+ struct regmap *sys_regs;
+};
+#define to_bt1_pcie(_dw) container_of(_dw, struct bt1_pcie, dw)
+
+/*
+ * Baikal-T1 MMIO space must be read/written by the dword-aligned
+ * instructions. Note the methods are optimized to have the dword operations
+ * performed with minimum overhead as the most frequently used ones.
+ */
+static int bt1_pcie_read_mmio(void __iomem *addr, int size, u32 *val)
+{
+ unsigned int ofs = (uintptr_t)addr & 0x3;
+
+ if (!IS_ALIGNED((uintptr_t)addr, size))
+ return -EINVAL;
+
+ *val = readl(addr - ofs) >> ofs * BITS_PER_BYTE;
+ if (size == 4) {
+ return 0;
+ } else if (size == 2) {
+ *val &= 0xffff;
+ return 0;
+ } else if (size == 1) {
+ *val &= 0xff;
+ return 0;
+ }
+
+ return -EINVAL;
+}
+
+static int bt1_pcie_write_mmio(void __iomem *addr, int size, u32 val)
+{
+ unsigned int ofs = (uintptr_t)addr & 0x3;
+ u32 tmp, mask;
+
+ if (!IS_ALIGNED((uintptr_t)addr, size))
+ return -EINVAL;
+
+ if (size == 4) {
+ writel(val, addr);
+ return 0;
+ } else if (size == 2 || size == 1) {
+ mask = GENMASK(size * BITS_PER_BYTE - 1, 0);
+ tmp = readl(addr - ofs) & ~(mask << ofs * BITS_PER_BYTE);
+ tmp |= (val & mask) << ofs * BITS_PER_BYTE;
+ writel(tmp, addr - ofs);
+ return 0;
+ }
+
+ return -EINVAL;
+}
+
+static u32 bt1_pcie_read_dbi(struct dw_pcie *pci, void __iomem *base, u32 reg,
+ size_t size)
+{
+ int ret;
+ u32 val;
+
+ ret = bt1_pcie_read_mmio(base + reg, size, &val);
+ if (ret) {
+ dev_err(pci->dev, "Read DBI address failed\n");
+ return ~0U;
+ }
+
+ return val;
+}
+
+static void bt1_pcie_write_dbi(struct dw_pcie *pci, void __iomem *base, u32 reg,
+ size_t size, u32 val)
+{
+ int ret;
+
+ ret = bt1_pcie_write_mmio(base + reg, size, val);
+ if (ret)
+ dev_err(pci->dev, "Write DBI address failed\n");
+}
+
+static void bt1_pcie_write_dbi2(struct dw_pcie *pci, void __iomem *base, u32 reg,
+ size_t size, u32 val)
+{
+ struct bt1_pcie *btpci = to_bt1_pcie(pci);
+ int ret;
+
+ regmap_update_bits(btpci->sys_regs, BT1_CCU_PCIE_GENC,
+ BT1_CCU_PCIE_DBI2_MODE, BT1_CCU_PCIE_DBI2_MODE);
+
+ ret = bt1_pcie_write_mmio(base + reg, size, val);
+ if (ret)
+ dev_err(pci->dev, "Write DBI2 address failed\n");
+
+ regmap_update_bits(btpci->sys_regs, BT1_CCU_PCIE_GENC,
+ BT1_CCU_PCIE_DBI2_MODE, 0);
+}
+
+static int bt1_pcie_start_link(struct dw_pcie *pci)
+{
+ struct bt1_pcie *btpci = to_bt1_pcie(pci);
+ u32 val;
+ int ret;
+
+ /*
+ * Enable LTSSM and make sure it was able to establish both PHY and
+ * data links. This procedure shall work fine to reach 2.5 GT/s speed.
+ */
+ regmap_update_bits(btpci->sys_regs, BT1_CCU_PCIE_GENC,
+ BT1_CCU_PCIE_LTSSM_EN, BT1_CCU_PCIE_LTSSM_EN);
+
+ ret = regmap_read_poll_timeout(btpci->sys_regs, BT1_CCU_PCIE_PMSC, val,
+ (val & BT1_CCU_PCIE_SMLH_LINKUP),
+ BT1_PCIE_LNK_DELAY_US, BT1_PCIE_LNK_TIMEOUT_US);
+ if (ret) {
+ dev_err(pci->dev, "LTSSM failed to set PHY link up\n");
+ return ret;
+ }
+
+ ret = regmap_read_poll_timeout(btpci->sys_regs, BT1_CCU_PCIE_PMSC, val,
+ (val & BT1_CCU_PCIE_RDLH_LINKUP),
+ BT1_PCIE_LNK_DELAY_US, BT1_PCIE_LNK_TIMEOUT_US);
+ if (ret) {
+ dev_err(pci->dev, "LTSSM failed to set data link up\n");
+ return ret;
+ }
+
+ /*
+ * Activate direct speed change after the link is established in an
+ * attempt to reach a higher bus performance (up to Gen.3 - 8.0 GT/s).
+ * This is required at least to get 8.0 GT/s speed.
+ */
+ val = dw_pcie_readl_dbi(pci, PCIE_LINK_WIDTH_SPEED_CONTROL);
+ val |= PORT_LOGIC_SPEED_CHANGE;
+ dw_pcie_writel_dbi(pci, PCIE_LINK_WIDTH_SPEED_CONTROL, val);
+
+ ret = regmap_read_poll_timeout(btpci->sys_regs, BT1_CCU_PCIE_PMSC, val,
+ BT1_CCU_PCIE_LTSSM_LINKUP(val),
+ BT1_PCIE_LNK_DELAY_US, BT1_PCIE_LNK_TIMEOUT_US);
+ if (ret)
+ dev_err(pci->dev, "LTSSM failed to get into L0 state\n");
+
+ return ret;
+}
+
+static void bt1_pcie_stop_link(struct dw_pcie *pci)
+{
+ struct bt1_pcie *btpci = to_bt1_pcie(pci);
+
+ regmap_update_bits(btpci->sys_regs, BT1_CCU_PCIE_GENC,
+ BT1_CCU_PCIE_LTSSM_EN, 0);
+}
+
+static const struct dw_pcie_ops bt1_pcie_ops = {
+ .read_dbi = bt1_pcie_read_dbi,
+ .write_dbi = bt1_pcie_write_dbi,
+ .write_dbi2 = bt1_pcie_write_dbi2,
+ .start_link = bt1_pcie_start_link,
+ .stop_link = bt1_pcie_stop_link,
+};
+
+static struct pci_ops bt1_pci_ops = {
+ .map_bus = dw_pcie_own_conf_map_bus,
+ .read = pci_generic_config_read32,
+ .write = pci_generic_config_write32,
+};
+
+static int bt1_pcie_get_resources(struct bt1_pcie *btpci)
+{
+ struct device *dev = btpci->dw.dev;
+ int i;
+
+ /* DBI access is supposed to be performed by the dword-aligned IOs */
+ btpci->dw.pp.bridge->ops = &bt1_pci_ops;
+
+ /* These CSRs are in MMIO so we won't check the regmap-methods status */
+ btpci->sys_regs =
+ syscon_regmap_lookup_by_phandle(dev->of_node, "baikal,bt1-syscon");
+ if (IS_ERR(btpci->sys_regs))
+ return dev_err_probe(dev, PTR_ERR(btpci->sys_regs),
+ "Failed to get syscon\n");
+
+ /* Make sure all the required resources have been specified */
+ for (i = 0; i < BT1_PCIE_NUM_APP_CLKS; i++) {
+ if (!btpci->dw.app_clks[bt1_pcie_app_clks[i]].clk) {
+ dev_err(dev, "App clocks set is incomplete\n");
+ return -ENOENT;
+ }
+ }
+
+ for (i = 0; i < BT1_PCIE_NUM_CORE_CLKS; i++) {
+ if (!btpci->dw.core_clks[bt1_pcie_core_clks[i]].clk) {
+ dev_err(dev, "Core clocks set is incomplete\n");
+ return -ENOENT;
+ }
+ }
+
+ for (i = 0; i < BT1_PCIE_NUM_APP_RSTS; i++) {
+ if (!btpci->dw.app_rsts[bt1_pcie_app_rsts[i]].rstc) {
+ dev_err(dev, "App resets set is incomplete\n");
+ return -ENOENT;
+ }
+ }
+
+ for (i = 0; i < BT1_PCIE_NUM_CORE_RSTS; i++) {
+ if (!btpci->dw.core_rsts[bt1_pcie_core_rsts[i]].rstc) {
+ dev_err(dev, "Core resets set is incomplete\n");
+ return -ENOENT;
+ }
+ }
+
+ return 0;
+}
+
+static void bt1_pcie_full_stop_bus(struct bt1_pcie *btpci, bool init)
+{
+ struct device *dev = btpci->dw.dev;
+ struct dw_pcie *pci = &btpci->dw;
+ int ret;
+
+ /* Disable LTSSM for sure */
+ regmap_update_bits(btpci->sys_regs, BT1_CCU_PCIE_GENC,
+ BT1_CCU_PCIE_LTSSM_EN, 0);
+
+ /*
+ * Application reset controls are trigger-based so assert the core
+ * resets only.
+ */
+ ret = reset_control_bulk_assert(DW_PCIE_NUM_CORE_RSTS, pci->core_rsts);
+ if (ret)
+ dev_err(dev, "Failed to assert core resets\n");
+
+ /*
+ * Clocks are disabled by default at least in accordance with the clk
+ * enable counter value on init stage.
+ */
+ if (!init) {
+ clk_bulk_disable_unprepare(DW_PCIE_NUM_CORE_CLKS, pci->core_clks);
+
+ clk_bulk_disable_unprepare(DW_PCIE_NUM_APP_CLKS, pci->app_clks);
+ }
+
+ /* The peripheral devices are unavailable anyway so reset them too */
+ gpiod_set_value_cansleep(pci->pe_rst, 1);
+
+ /* Make sure all the resets are settled */
+ msleep(BT1_PCIE_RST_DELAY_MS);
+}
+
+/*
+ * Implements the cold reset procedure in accordance with the reference manual
+ * and available PM signals.
+ */
+static int bt1_pcie_cold_start_bus(struct bt1_pcie *btpci)
+{
+ struct device *dev = btpci->dw.dev;
+ struct dw_pcie *pci = &btpci->dw;
+ u32 val;
+ int ret;
+
+ /* First get out of the Power/Hot reset state */
+ ret = reset_control_deassert(pci->core_rsts[DW_PCIE_PWR_RST].rstc);
+ if (ret) {
+ dev_err(dev, "Failed to deassert PHY reset\n");
+ return ret;
+ }
+
+ ret = reset_control_deassert(pci->core_rsts[DW_PCIE_HOT_RST].rstc);
+ if (ret) {
+ dev_err(dev, "Failed to deassert hot reset\n");
+ goto err_assert_pwr_rst;
+ }
+
+ /* Wait for the PM-core to stop requesting the PHY reset */
+ ret = regmap_read_poll_timeout(btpci->sys_regs, BT1_CCU_PCIE_RSTC, val,
+ !(val & BT1_CCU_PCIE_REQ_PHY_RST),
+ BT1_PCIE_REQ_DELAY_US, BT1_PCIE_REQ_TIMEOUT_US);
+ if (ret) {
+ dev_err(dev, "Timed out waiting for PM to stop PHY resetting\n");
+ goto err_assert_hot_rst;
+ }
+
+ ret = reset_control_deassert(pci->core_rsts[DW_PCIE_PHY_RST].rstc);
+ if (ret) {
+ dev_err(dev, "Failed to deassert PHY reset\n");
+ goto err_assert_hot_rst;
+ }
+
+ /* Clocks can be now enabled, but the ref one is crucial at this stage */
+ ret = clk_bulk_prepare_enable(DW_PCIE_NUM_APP_CLKS, pci->app_clks);
+ if (ret) {
+ dev_err(dev, "Failed to enable app clocks\n");
+ goto err_assert_phy_rst;
+ }
+
+ ret = clk_bulk_prepare_enable(DW_PCIE_NUM_CORE_CLKS, pci->core_clks);
+ if (ret) {
+ dev_err(dev, "Failed to enable ref clocks\n");
+ goto err_disable_app_clk;
+ }
+
+ /* Wait for the PM to stop requesting the controller core reset */
+ ret = regmap_read_poll_timeout(btpci->sys_regs, BT1_CCU_PCIE_RSTC, val,
+ !(val & BT1_CCU_PCIE_REQ_CORE_RST),
+ BT1_PCIE_REQ_DELAY_US, BT1_PCIE_REQ_TIMEOUT_US);
+ if (ret) {
+ dev_err(dev, "Timed out waiting for PM to stop core resetting\n");
+ goto err_disable_core_clk;
+ }
+
+ /* PCS-PIPE interface and controller core can be now activated */
+ ret = reset_control_deassert(pci->core_rsts[DW_PCIE_PIPE_RST].rstc);
+ if (ret) {
+ dev_err(dev, "Failed to deassert PIPE reset\n");
+ goto err_disable_core_clk;
+ }
+
+ ret = reset_control_deassert(pci->core_rsts[DW_PCIE_CORE_RST].rstc);
+ if (ret) {
+ dev_err(dev, "Failed to deassert core reset\n");
+ goto err_assert_pipe_rst;
+ }
+
+ /* It's recommended to reset the core and application logic together */
+ ret = reset_control_bulk_reset(DW_PCIE_NUM_APP_RSTS, pci->app_rsts);
+ if (ret) {
+ dev_err(dev, "Failed to reset app domain\n");
+ goto err_assert_core_rst;
+ }
+
+ /* Sticky/Non-sticky CSR flags can be now unreset too */
+ ret = reset_control_deassert(pci->core_rsts[DW_PCIE_STICKY_RST].rstc);
+ if (ret) {
+ dev_err(dev, "Failed to deassert sticky reset\n");
+ goto err_assert_core_rst;
+ }
+
+ ret = reset_control_deassert(pci->core_rsts[DW_PCIE_NON_STICKY_RST].rstc);
+ if (ret) {
+ dev_err(dev, "Failed to deassert non-sticky reset\n");
+ goto err_assert_sticky_rst;
+ }
+
+ /* Activate the PCIe bus peripheral devices */
+ gpiod_set_value_cansleep(pci->pe_rst, 0);
+
+ /* Make sure the state is settled (LTSSM is still disabled though) */
+ usleep_range(BT1_PCIE_RUN_DELAY_US, BT1_PCIE_RUN_DELAY_US + 100);
+
+ return 0;
+
+err_assert_sticky_rst:
+ reset_control_assert(pci->core_rsts[DW_PCIE_STICKY_RST].rstc);
+
+err_assert_core_rst:
+ reset_control_assert(pci->core_rsts[DW_PCIE_CORE_RST].rstc);
+
+err_assert_pipe_rst:
+ reset_control_assert(pci->core_rsts[DW_PCIE_PIPE_RST].rstc);
+
+err_disable_core_clk:
+ clk_bulk_disable_unprepare(DW_PCIE_NUM_CORE_CLKS, pci->core_clks);
+
+err_disable_app_clk:
+ clk_bulk_disable_unprepare(DW_PCIE_NUM_APP_CLKS, pci->app_clks);
+
+err_assert_phy_rst:
+ reset_control_assert(pci->core_rsts[DW_PCIE_PHY_RST].rstc);
+
+err_assert_hot_rst:
+ reset_control_assert(pci->core_rsts[DW_PCIE_HOT_RST].rstc);
+
+err_assert_pwr_rst:
+ reset_control_assert(pci->core_rsts[DW_PCIE_PWR_RST].rstc);
+
+ return ret;
+}
+
+static int bt1_pcie_host_init(struct dw_pcie_rp *pp)
+{
+ struct dw_pcie *pci = to_dw_pcie_from_pp(pp);
+ struct bt1_pcie *btpci = to_bt1_pcie(pci);
+ int ret;
+
+ ret = bt1_pcie_get_resources(btpci);
+ if (ret)
+ return ret;
+
+ bt1_pcie_full_stop_bus(btpci, true);
+
+ return bt1_pcie_cold_start_bus(btpci);
+}
+
+static void bt1_pcie_host_deinit(struct dw_pcie_rp *pp)
+{
+ struct dw_pcie *pci = to_dw_pcie_from_pp(pp);
+ struct bt1_pcie *btpci = to_bt1_pcie(pci);
+
+ bt1_pcie_full_stop_bus(btpci, false);
+}
+
+static const struct dw_pcie_host_ops bt1_pcie_host_ops = {
+ .host_init = bt1_pcie_host_init,
+ .host_deinit = bt1_pcie_host_deinit,
+};
+
+static struct bt1_pcie *bt1_pcie_create_data(struct platform_device *pdev)
+{
+ struct bt1_pcie *btpci;
+
+ btpci = devm_kzalloc(&pdev->dev, sizeof(*btpci), GFP_KERNEL);
+ if (!btpci)
+ return ERR_PTR(-ENOMEM);
+
+ btpci->pdev = pdev;
+
+ platform_set_drvdata(pdev, btpci);
+
+ return btpci;
+}
+
+static int bt1_pcie_add_port(struct bt1_pcie *btpci)
+{
+ struct device *dev = &btpci->pdev->dev;
+ int ret;
+
+ btpci->dw.version = DW_PCIE_VER_460A;
+ btpci->dw.dev = dev;
+ btpci->dw.ops = &bt1_pcie_ops;
+
+ btpci->dw.pp.num_vectors = MAX_MSI_IRQS;
+ btpci->dw.pp.ops = &bt1_pcie_host_ops;
+
+ dw_pcie_cap_set(&btpci->dw, REQ_RES);
+
+ ret = dw_pcie_host_init(&btpci->dw.pp);
+ if (ret)
+ dev_err_probe(dev, ret, "Failed to initialize DWC PCIe host\n");
+
+ return ret;
+}
+
+static void bt1_pcie_del_port(struct bt1_pcie *btpci)
+{
+ dw_pcie_host_deinit(&btpci->dw.pp);
+}
+
+static int bt1_pcie_probe(struct platform_device *pdev)
+{
+ struct bt1_pcie *btpci;
+
+ btpci = bt1_pcie_create_data(pdev);
+ if (IS_ERR(btpci))
+ return PTR_ERR(btpci);
+
+ return bt1_pcie_add_port(btpci);
+}
+
+static int bt1_pcie_remove(struct platform_device *pdev)
+{
+ struct bt1_pcie *btpci = platform_get_drvdata(pdev);
+
+ bt1_pcie_del_port(btpci);
+
+ return 0;
+}
+
+static const struct of_device_id bt1_pcie_of_match[] = {
+ { .compatible = "baikal,bt1-pcie" },
+ {},
+};
+MODULE_DEVICE_TABLE(of, bt1_pcie_of_match);
+
+static struct platform_driver bt1_pcie_driver = {
+ .probe = bt1_pcie_probe,
+ .remove = bt1_pcie_remove,
+ .driver = {
+ .name = "bt1-pcie",
+ .of_match_table = bt1_pcie_of_match,
+ },
+};
+module_platform_driver(bt1_pcie_driver);
+
+MODULE_AUTHOR("Serge Semin <Sergey.Semin@xxxxxxxxxxxxxxxxxxxx>");
+MODULE_DESCRIPTION("Baikal-T1 PCIe driver");
+MODULE_LICENSE("GPL");
--
2.38.0
