Dne ponedeljek, 07. november 2022 ob 01:54:23 CET je Andre Przywara napisal(a): > This is a fixed version of the initial post. I dropped the two patches > that were already applied by the respective maintainers, and fixed the > smaller issues mentioned in the review. > This adds v2 of the series enabling the "Lctech Pi F1C200s" board on top, > also with the comments addressed. Please don't combine series if not agreed upon before. Now whole series will be delayed until USB is sorted out. Best regards, Jernej > The whole series goes on top of v3 of Icenowy's F1C100s USB support > series [1]. There is no real conflict, but the lctech-pi.dts file > references the new USB DT nodes from the .dtsi. > > I put a git repo with all those patches up here: > https://github.com/apritzel/linux/commits/f1c100s-devices-v2 > > For a changelog see below. > > [1] > https://lore.kernel.org/linux-arm-kernel/20221106154826.6687-1-andre.przywa > ra@xxxxxxx/T/#t > > ================= > The Allwinner F1C100s series of SoCs shares many peripherals with other > Allwinner SoCs. Since they are compatible, we can use the existing > drivers, and just need to enable the devices in the DT. > > This series adds the I2C controllers, the PWM device, the CIR (infrared) > device and the LRADC (aka. KEYADC, low res ADC) to the F1C100s .dtsi, so > boards can just use them by setting 'status = "okay";'. > > The only thing missing driver-wise is the IR mod clock, which was not > modeled in our CCU driver. Patch 4/10 fixes that. > > For every device there is one patch that adds the new compatible string > to the DT binding, and another patch to add the DT node. > > This has been tested on the Lctech Pi F1C200s board, by: > - Connecting an LED to PE6, and configuring this as the PWM pin in the DT. > Doing a sweep on /sys/class/pwm/pwm1/duty_cycle made the LED fade out. > - Configuring PD0/PD12 as I2C0, and letting i2c-detect find the on-board > NS2009 I2C chip. > - Connecting two resistors to the "ADC" pin, and configuring them as two > buttons in the DT. /dev/input/event0 properly reported button presses. > - Connecting an infrared receiver to PE11, configured as CIR. > ir-keytable reported key presses on a remote control. > > All those (basic) tests were successful, and prove that the peripherals > do work and are compatible. > > The final three patches add the binding docs and the .dts file for the > Lctech Pi F1C200s development board. > > Please have a look and test on your hardware, if possible. > > Cheers, > Andre > > Changelog v1 ... v2: > - dropped former patch 3/9 and 8/9: already applied > - increase register frame size in DT for PWM and LRADC > - drop I2C1 pins from pinctroller DT node > - increase IR mod clock mux to 2 bits > - fix mistyped comma in vendor prefix name > - drop unneeded mmc0 and spi0 aliases from Lctech Pi DT > - add /omit-if-no-ref/ tag to UART1 pins > - add ACKs and Reviewed-by tags > > > Andre Przywara (10): > dt-bindings: pwm: allwinner,sun4i-a10: Add F1C100s compatible > ARM: dts: suniv: f1c100s: add PWM node > ARM: dts: suniv: f1c100s: add I2C DT nodes > clk: sunxi-ng: f1c100s: Add IR mod clock > dt-bindings: media: IR: Add F1C100s IR compatible string > ARM: dts: suniv: f1c100s: add CIR DT node > ARM: dts: suniv: f1c100s: add LRADC node > dt-bindings: vendor-prefixes: add Lctech name > dt-bindings: arm: sunxi: add compatible strings for Lctech Pi > ARM: dts: suniv: Add Lctech Pi F1C200s devicetree > > .../devicetree/bindings/arm/sunxi.yaml | 6 ++ > .../media/allwinner,sun4i-a10-ir.yaml | 1 + > .../bindings/pwm/allwinner,sun4i-a10-pwm.yaml | 4 +- > .../devicetree/bindings/vendor-prefixes.yaml | 2 + > arch/arm/boot/dts/Makefile | 1 + > arch/arm/boot/dts/suniv-f1c100s.dtsi | 76 ++++++++++++++++++ > arch/arm/boot/dts/suniv-f1c200s-lctech-pi.dts | 78 +++++++++++++++++++ > drivers/clk/sunxi-ng/ccu-suniv-f1c100s.c | 11 ++- > drivers/clk/sunxi-ng/ccu-suniv-f1c100s.h | 2 +- > include/dt-bindings/clock/suniv-ccu-f1c100s.h | 2 + > 10 files changed, 180 insertions(+), 3 deletions(-) > create mode 100644 arch/arm/boot/dts/suniv-f1c200s-lctech-pi.dts > > -- > 2.35.5
