On 04/11/2022 05:05, Trilok Soni wrote:
+ Adding Konrad, Bjorn is already there in this email
On 11/3/2022 2:13 PM, Melody Olvera wrote:
On 11/2/2022 9:24 AM, Krzysztof Kozlowski wrote:
On 31/10/2022 17:49, Melody Olvera wrote:
On 10/27/2022 8:21 AM, Krzysztof Kozlowski wrote:
On 26/10/2022 16:04, Melody Olvera wrote:
Add the base DTSI files for QDU1000 and QRU1000 SoCs, including base
descriptions of CPUs, GCC, RPMHCC, QUP, TLMM, and
interrupt-controller
to boot to shell with console on these SoCs.
Signed-off-by: Melody Olvera <quic_molvera@xxxxxxxxxxx>
---
arch/arm64/boot/dts/qcom/qdu1000.dtsi | 1406
+++++++++++++++++++++++++
Please use scripts/get_maintainers.pl to get a list of necessary
people
and lists to CC. It might happen, that command when run on an older
kernel, gives you outdated entries. Therefore please be sure you
base
your patches on recent Linux kernel.
Sure thing; we talked about this on a different patch.
arch/arm64/boot/dts/qcom/qru1000.dtsi | 27 +
2 files changed, 1433 insertions(+)
create mode 100644 arch/arm64/boot/dts/qcom/qdu1000.dtsi
create mode 100644 arch/arm64/boot/dts/qcom/qru1000.dtsi
diff --git a/arch/arm64/boot/dts/qcom/qdu1000.dtsi
b/arch/arm64/boot/dts/qcom/qdu1000.dtsi
new file mode 100644
index 000000000000..76474106e931
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/qdu1000.dtsi
@@ -0,0 +1,1406 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2022 Qualcomm Innovation Center, Inc. All
rights reserved.
+ */
(...)
+
+ soc: soc@0 {
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges = <0 0 0 0 0x10 0>;
+ dma-ranges = <0 0 0 0 0x10 0>;
+ compatible = "simple-bus";
+
+ gcc: clock-controller@80000 {
+ compatible = "qcom,gcc-qdu1000", "syscon";
+ reg = <0x0 0x80000 0x0 0x1f4200>;
+ #clock-cells = <1>;
+ #reset-cells = <1>;
+ #power-domain-cells = <1>;
+ clocks = <&rpmhcc RPMH_CXO_CLK>, <&sleep_clk>;
+ clock-names = "bi_tcxo", "sleep_clk";
+ };
+
+ gpi_dma0: dma-controller@900000 {
+ compatible = "qcom,sm6350-gpi-dma";
You should add here a specific compatible as well. Same in other
places.
All places. I had impression we talked about this few times, so I
don't
know what is missing on your side.
This must be:
"qcom,qdu1000-gpi-dma", "qcom,sm6350-gpi-dma"
Got it. I talked to Stephan and he said either your suggestion or
just using
preexisting compatibles would be ok. I thought it might be cleaner
to not
have the qdu compats, but I'm fine either way.
We use specific compats so that if it turns out this specific SoC (or
rather the
bundled firmware) has some peculiar bugs, we can retroactively only
apply them
to that specific SoC by adding the compatible somewhere in .c code if
need be.
+ #dma-cells = <3>;
+ reg = <0x0 0x900000 0x0 0x60000>;
+ interrupts = <GIC_SPI 244 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 245 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 246 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 247 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 248 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 249 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 250 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 251 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 252 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 253 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 254 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 255 IRQ_TYPE_LEVEL_HIGH>;
+ dma-channels = <12>;
+ dma-channel-mask = <0x3f>;
+ iommus = <&apps_smmu 0xf6 0x0>;
+ };
+
(...)
+
+ tlmm: pinctrl@f000000 {
+ compatible = "qcom,qdu1000-tlmm";
+ reg = <0x0 0xf000000 0x0 0x1000000>;
+ interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ gpio-ranges = <&tlmm 0 0 151>;
+ wakeup-parent = <&pdc>;
+
+ qup_uart0_default: qup-uart0-default-state {
+ pins = "gpio6", "gpio7", "gpio8", "gpio9";
+ function = "qup00";
+ };
+
+ qup_i2c1_data_clk: qup-i2c1-data-clk-state {
+ pins = "gpio10", "gpio11";
+ function = "qup01";
+ drive-strength = <2>;
Can we have some generic agreement where to put drive-strengths
and bias?
See also:
https://lore.kernel.org/linux-devicetree/20221026200357.391635-2-krzysztof.kozlowski@xxxxxxxxxx/
https://lore.kernel.org/lkml/CAD=FV=VUL4GmjaibAMhKNdpEso_Hg_R=XeMaqah1LSj_9-Ce4Q@xxxxxxxxxxxxxx/
I agree with Doug on having 'generic' drive-strength. Moreover, maybe
even adding some property like
bias-type = <NONE/PULL_DOWN/...> would be cool to make it more flexible
so that we could trim off
A LOT of repeated lines (remember, most boards are more or less copies
of the reference design for a
given platform like QRD or CRD) going forward.
Not sure how much two-sense I have for the conversation at large,
but generally I agree with Doug's
point in the first paragraph. Pulls for this soc are consistent
across boards so I don't think it makes
sense to move them to the board files here. I vote that these stay
here.
I would be great if Konrad and Bjorn shared their opinion on this...
but
wait, you did not Cc all maintainers... Eh.
I'm not sure why this is being brought up again; we've already
discussed this here
https://lore.kernel.org/all/9707bf67-1b22-8a77-7193-fc909b4f49de@xxxxxxxxxxx/
Would you like to discuss this issue here, on the next version, or
not at all?
On a side note, I'm uncomfortable with how our continued interactions
are going
and do not believe this to be conductive to continued collaboration.
I would ask that
we keep our correspondence polite and professional moving forward.
I have added Konrad and Bjorn is already there on the thread. Our
understanding is that CCing maintainers comment is for next patch
series after this one.
BTW: you can feed git send-email with
--cc-cmd='./scripts/get_maintainer.pl --norolestats' and
it'll pick the right people for you (most of the time, anyway).
Bjorn, please check and comment on above? If requires we should start
writing the guidelines for MSM boards since lot of comments are based
on the experience or knowledge in the community Vs caught by tools -
so it is easy to be missed by developers submitting new boards. Thoughts?
Big yes! Some of the points should probably even be raised wrt the DT
spec itself, such as property order.
Konrad
---Trilok Soni
