Quoting Sean Anderson (2022-10-27 12:11:08)
> diff --git a/drivers/phy/freescale/Kconfig b/drivers/phy/freescale/Kconfig
> index 853958fb2c06..a6ccccf9e39b 100644
> --- a/drivers/phy/freescale/Kconfig
> +++ b/drivers/phy/freescale/Kconfig
> @@ -47,3 +47,25 @@ config PHY_FSL_LYNX_28G
> found on NXP's Layerscape platforms such as LX2160A.
> Used to change the protocol running on SerDes lanes at runtime.
> Only useful for a restricted set of Ethernet protocols.
> +
> +config PHY_FSL_LYNX_10G
> + tristate "Freescale QorIQ Lynx 10G SerDes support"
> + depends on COMMON_CLK
Does something not compile if COMMON_CLK is disabled?
> + depends on ARCH_LAYERSCAPE || PPC || COMPILE_TEST
> + select GENERIC_PHY
> + select REGMAP_MMIO
> + help
> + This adds support for the Lynx "SerDes" devices found on various QorIQ
> + SoCs. There may be up to four SerDes devices on each SoC, and each
> + device supports up to eight lanes. The SerDes is configured by
> + default by the RCW, but this module is necessary in order to support
> + some modes (such as 2.5G SGMII or 1000BASE-KX), or clock setups (as
> + only as subset of clock configurations are supported by the RCW).
> + The hardware supports a variety of protocols, including Ethernet,
> + SATA, PCIe, and more exotic links such as Interlaken and Aurora. This
> + driver only supports Ethernet, but it will try not to touch lanes
> + configured for other protocols.
> +
> + If you have a QorIQ processor and want to dynamically reconfigure your
> + SerDes, say Y. If this driver is compiled as a module, it will be
> + named phy-fsl-lynx-10g-drv.
> diff --git a/drivers/phy/freescale/Makefile b/drivers/phy/freescale/Makefile
> index cedb328bc4d2..1f18936507e0 100644
> --- a/drivers/phy/freescale/Makefile
> +++ b/drivers/phy/freescale/Makefile
> @@ -3,4 +3,7 @@ obj-$(CONFIG_PHY_FSL_IMX8MQ_USB) += phy-fsl-imx8mq-usb.o
> obj-$(CONFIG_PHY_MIXEL_LVDS_PHY) += phy-fsl-imx8qm-lvds-phy.o
> obj-$(CONFIG_PHY_MIXEL_MIPI_DPHY) += phy-fsl-imx8-mipi-dphy.o
> obj-$(CONFIG_PHY_FSL_IMX8M_PCIE) += phy-fsl-imx8m-pcie.o
> +phy-fsl-lynx-10g-drv-y += phy-fsl-lynx-10g.o
> +phy-fsl-lynx-10g-drv-y += phy-fsl-lynx-10g-clk.o
> +obj-$(CONFIG_PHY_FSL_LYNX_10G) += phy-fsl-lynx-10g-drv.o
> obj-$(CONFIG_PHY_FSL_LYNX_28G) += phy-fsl-lynx-28g.o
> diff --git a/drivers/phy/freescale/lynx-10g.h b/drivers/phy/freescale/lynx-10g.h
> new file mode 100644
> index 000000000000..75d9353a867b
> --- /dev/null
> +++ b/drivers/phy/freescale/lynx-10g.h
> @@ -0,0 +1,16 @@
> +/* SPDX-License-Identifier: GPL-2.0 */
> +/*
> + * Copyright (C) 2022 Sean Anderson <sean.anderson@xxxxxxxx>
> + */
> +
> +#ifndef LYNX_10G
> +#define LYNX_10G
> +
> +struct clk;
> +struct device;
> +struct regmap;
> +
> +int lynx_clks_init(struct device *dev, struct regmap *regmap,
Can you use auxiliary bus to register this clk controller instead and
then move the clk file to drivers/clk/?
> + struct clk *plls[2], struct clk *ex_dlys[2]);
> +
> +#endif /* LYNX 10G */
> diff --git a/drivers/phy/freescale/phy-fsl-lynx-10g-clk.c b/drivers/phy/freescale/phy-fsl-lynx-10g-clk.c
> new file mode 100644
> index 000000000000..6ec32bdfb9dd
> --- /dev/null
> +++ b/drivers/phy/freescale/phy-fsl-lynx-10g-clk.c
> @@ -0,0 +1,503 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Copyright (C) 2022 Sean Anderson <sean.anderson@xxxxxxxx>
> + *
> + * This file contains the implementation for the PLLs found on Lynx 10G phys.
> + *
> + * XXX: The VCO rate of the PLLs can exceed ~4GHz, which is the maximum rate
> + * expressable in an unsigned long. To work around this, rates are specified in
> + * kHz. This is as if there was a division by 1000 in the PLL.
> + */
> +
> +#include <linux/clk.h>
Ideally clk.h isn't included in a clk provider. This allows us to easily
identify drivers that are both a consumer (clk.h) and a provider
(clk-provider.h). A provider/consumer is rare.
> +#include <linux/clk-provider.h>
> +#include <linux/device.h>
> +#include <linux/bitfield.h>
> +#include <linux/math64.h>
> +#include <linux/regmap.h>
> +#include <linux/slab.h>
> +#include <linux/units.h>
> +#include <dt-bindings/clock/fsl,lynx-10g.h>
> +
> +#include "lynx-10g.h"
> +
> +#define PLL_STRIDE 0x20
> +#define PLLa(a, off) ((a) * PLL_STRIDE + (off))
> +#define PLLaRSTCTL(a) PLLa(a, 0x00)
> +#define PLLaCR0(a) PLLa(a, 0x04)
> +
> +#define PLLaRSTCTL_RSTREQ BIT(31)
> +#define PLLaRSTCTL_RST_DONE BIT(30)
> +#define PLLaRSTCTL_RST_ERR BIT(29)
> +#define PLLaRSTCTL_PLLRST_B BIT(7)
> +#define PLLaRSTCTL_SDRST_B BIT(6)
> +#define PLLaRSTCTL_SDEN BIT(5)
> +
> +#define PLLaRSTCTL_ENABLE_SET (PLLaRSTCTL_RST_DONE | PLLaRSTCTL_PLLRST_B | \
> + PLLaRSTCTL_SDRST_B | PLLaRSTCTL_SDEN)
> +#define PLLaRSTCTL_ENABLE_MASK (PLLaRSTCTL_ENABLE_SET | PLLaRSTCTL_RST_ERR)
> +
> +#define PLLaCR0_POFF BIT(31)
> +#define PLLaCR0_RFCLK_SEL GENMASK(30, 28)
> +#define PLLaCR0_PLL_LCK BIT(23)
> +#define PLLaCR0_FRATE_SEL GENMASK(19, 16)
> +#define PLLaCR0_DLYDIV_SEL GENMASK(1, 0)
> +
> +#define PLLaCR0_DLYDIV_SEL_16 0b01
> +
> +/**
> + * struct lynx_clk - Driver data for the PLLs
> + * @pll: The PLL clock
> + * @ex_dly: The "PLLa_ex_dly_clk" clock
> + * @ref: Our reference clock
> + * @dev: The serdes device
> + * @regmap: Our registers
> + * @idx: Which PLL this clock is for
> + */
> +struct lynx_clk {
> + struct clk_hw pll, ex_dly;
> + struct clk_hw *ref;
> + struct device *dev;
> + struct regmap *regmap;
> + unsigned int idx;
> +};
> +
> +static u32 lynx_read(struct lynx_clk *clk, u32 reg)
> +{
> + unsigned int ret = 0;
> +
> + WARN_ON_ONCE(regmap_read(clk->regmap, reg, &ret));
> + return ret;
> +}
> +
> +static void lynx_write(struct lynx_clk *clk, u32 val, u32 reg)
> +{
> + WARN_ON_ONCE(regmap_write(clk->regmap, reg, val));
> +}
> +
> +static struct lynx_clk *lynx_pll_to_clk(struct clk_hw *hw)
> +{
> + return container_of(hw, struct lynx_clk, pll);
> +}
> +
> +static struct lynx_clk *lynx_ex_dly_to_clk(struct clk_hw *hw)
> +{
> + return container_of(hw, struct lynx_clk, ex_dly);
> +}
> +
> +static void lynx_pll_stop(struct lynx_clk *clk)
> +{
> + u32 rstctl;
> +
> + rstctl = lynx_read(clk, PLLaRSTCTL(clk->idx));
> + rstctl &= ~PLLaRSTCTL_SDRST_B;
> + lynx_write(clk, rstctl, PLLaRSTCTL(clk->idx));
> +
> + ndelay(50);
> +
> + rstctl = lynx_read(clk, PLLaRSTCTL(clk->idx));
> + rstctl &= ~(PLLaRSTCTL_SDEN | PLLaRSTCTL_PLLRST_B);
> + lynx_write(clk, rstctl, PLLaRSTCTL(clk->idx));
> +
> + ndelay(100);
> +}
> +
> +static void lynx_pll_disable(struct clk_hw *hw)
> +{
> + struct lynx_clk *clk = lynx_pll_to_clk(hw);
> + u32 cr0;
> +
> + dev_dbg(clk->dev, "disable pll%d\n", clk->idx);
> +
> + lynx_pll_stop(clk);
> +
> + cr0 = lynx_read(clk, PLLaCR0(clk->idx));
> + cr0 |= PLLaCR0_POFF;
> + lynx_write(clk, cr0, PLLaCR0(clk->idx));
> +}
> +
> +static int lynx_pll_reset(struct lynx_clk *clk)
> +{
> + int ret;
> + u32 rstctl = lynx_read(clk, PLLaRSTCTL(clk->idx));
> +
> + rstctl |= PLLaRSTCTL_RSTREQ;
> + lynx_write(clk, rstctl, PLLaRSTCTL(clk->idx));
> + ret = read_poll_timeout(lynx_read, rstctl,
> + rstctl & (PLLaRSTCTL_RST_DONE | PLLaRSTCTL_RST_ERR),
> + 100, 5000, true, clk, PLLaRSTCTL(clk->idx));
> + if (rstctl & PLLaRSTCTL_RST_ERR)
> + ret = -EIO;
> + if (ret) {
> + dev_err(clk->dev, "pll%d reset failed\n", clk->idx);
> + return ret;
> + }
> +
> + rstctl |= PLLaRSTCTL_SDEN | PLLaRSTCTL_PLLRST_B | PLLaRSTCTL_SDRST_B;
> + lynx_write(clk, rstctl, PLLaRSTCTL(clk->idx));
> + return 0;
> +}
> +
> +static int lynx_pll_prepare(struct clk_hw *hw)
> +{
> + struct lynx_clk *clk = lynx_pll_to_clk(hw);
> + u32 rstctl = lynx_read(clk, PLLaRSTCTL(clk->idx));
> + u32 cr0 = lynx_read(clk, PLLaCR0(clk->idx));
> +
> + /*
> + * "Enabling" the PLL involves resetting it (and all attached lanes).
> + * Avoid doing this if we are already enabled.
> + */
> + if (!(cr0 & PLLaCR0_POFF) &&
> + (rstctl & PLLaRSTCTL_ENABLE_MASK) == PLLaRSTCTL_ENABLE_SET) {
> + dev_dbg(clk->dev, "pll%d already prepared\n", clk->idx);
> + return 0;
> + }
> +
> + dev_dbg(clk->dev, "prepare pll%d\n", clk->idx);
> +
> + cr0 &= ~PLLaCR0_POFF;
> + lynx_write(clk, cr0, PLLaCR0(clk->idx));
> +
> + return lynx_pll_reset(clk);
> +}
> +
> +static int lynx_pll_is_enabled(struct clk_hw *hw)
> +{
> + struct lynx_clk *clk = lynx_pll_to_clk(hw);
> + u32 cr0 = lynx_read(clk, PLLaCR0(clk->idx));
> + bool enabled = !(cr0 & PLLaCR0_POFF);
> +
> + dev_dbg(clk->dev, "pll%d %s enabled\n", clk->idx,
> + enabled ? "is" : "is not");
> +
> + return enabled;
> +}
> +
> +static const u32 rfclk_sel_map[8] = {
> + [0b000] = 100000000,
> + [0b001] = 125000000,
> + [0b010] = 156250000,
> + [0b011] = 150000000,
> +};
> +
> +/**
> + * lynx_rfclk_to_sel() - Convert a reference clock rate to a selector
> + * @rate: The reference clock rate
> + *
> + * To allow for some variation in the reference clock rate, up to 100ppm of
> + * error is allowed.
> + *
> + * Return: An appropriate selector for @rate, or -%EINVAL.
> + */
> +static int lynx_rfclk_to_sel(u32 rate)
Should rate be unsigned long? Or you really want 32-bits here?
> +{
> + int ret;
> +
> + for (ret = 0; ret < ARRAY_SIZE(rfclk_sel_map); ret++) {
> + u32 rfclk_rate = rfclk_sel_map[ret];
> + /* Allow an error of 100ppm */
> + u32 error = rfclk_rate / 10000;
> +
> + if (rate > rfclk_rate - error && rate < rfclk_rate + error)
Does
if (abs(rate - rfclk_rate) < error)
work? I'm kinda surprised that we don't have a within_tolerance(x,
margin) macro in math.h that would make it look like:
if (within_tolerance(rate - rfclk_rate, error))
> + return ret;
> + }
> +
> + return -EINVAL;
> +}
> +
> +static const u32 frate_sel_map[16] = {
> + [0b0000] = 5000000,
> + [0b0101] = 3750000,
> + [0b0110] = 5156250,
> + [0b0111] = 4000000,
> + [0b1001] = 3125000,
> + [0b1010] = 3000000,
> +};
> +
> +/**
> + * lynx_frate_to_sel() - Convert a VCO clock rate to a selector
> + * @rate_khz: The VCO frequency, in kHz
> + *
> + * Return: An appropriate selector for @rate_khz, or -%EINVAL.
> + */
> +static int lynx_frate_to_sel(u32 rate_khz)
> +{
> + int ret;
> +
> + for (ret = 0; ret < ARRAY_SIZE(frate_sel_map); ret++)
> + if (frate_sel_map[ret] == rate_khz)
> + return ret;
> +
> + return -EINVAL;
> +}
> +
> +static u32 lynx_pll_ratio(u32 frate_sel, u32 rfclk_sel)
> +{
> + u64 frate;
> + u32 rfclk, error, ratio;
> +
> + frate = frate_sel_map[frate_sel] * (u64)HZ_PER_KHZ;
> + rfclk = rfclk_sel_map[rfclk_sel];
> +
> + if (!frate || !rfclk)
> + return 0;
> +
> + ratio = div_u64_rem(frate, rfclk, &error);
> + if (!error)
> + return ratio;
> + return 0;
> +}
> +
> +static unsigned long lynx_pll_recalc_rate(struct clk_hw *hw,
> + unsigned long parent_rate)
> +{
> + struct lynx_clk *clk = lynx_pll_to_clk(hw);
> + u32 cr0 = lynx_read(clk, PLLaCR0(clk->idx));
> + u32 frate_sel = FIELD_GET(PLLaCR0_FRATE_SEL, cr0);
> + u32 rfclk_sel = FIELD_GET(PLLaCR0_RFCLK_SEL, cr0);
> + u32 ratio = lynx_pll_ratio(frate_sel, rfclk_sel);
> + unsigned long ret;
> +
> + /* Ensure that the parent matches our rfclk selector */
> + if (rfclk_sel == lynx_rfclk_to_sel(parent_rate))
> + ret = mult_frac(parent_rate, ratio, HZ_PER_KHZ);
> + else
> + ret = 0;
> +
> + dev_dbg(clk->dev, "recalc pll%d new=%llu parent=%lu\n", clk->idx,
> + (u64)ret * HZ_PER_KHZ, parent_rate);
> + return ret;
> +}
> +
> +static long lynx_pll_round_rate(struct clk_hw *hw, unsigned long rate_khz,
> + unsigned long *parent_rate)
> +{
> + int frate_sel, rfclk_sel;
> + struct lynx_clk *clk = lynx_pll_to_clk(hw);
> + u32 ratio;
> +
> + dev_dbg(clk->dev, "round pll%d new=%llu parent=%lu\n", clk->idx,
> + (u64)rate_khz * HZ_PER_KHZ, *parent_rate);
> +
> + frate_sel = lynx_frate_to_sel(rate_khz);
> + if (frate_sel < 0)
> + return frate_sel;
> +
> + /* Try the current parent rate */
> + rfclk_sel = lynx_rfclk_to_sel(*parent_rate);
> + if (rfclk_sel >= 0) {
> + ratio = lynx_pll_ratio(frate_sel, rfclk_sel);
> + if (ratio)
> + return mult_frac(*parent_rate, ratio, HZ_PER_KHZ);
> + }
> +
> + /* Try all possible parent rates */
> + for (rfclk_sel = 0;
> + rfclk_sel < ARRAY_SIZE(rfclk_sel_map);
> + rfclk_sel++) {
> + unsigned long new_parent_rate;
> +
> + ratio = lynx_pll_ratio(frate_sel, rfclk_sel);
> + if (!ratio)
> + continue;
> +
> + /* Ensure the reference clock can produce this rate */
> + new_parent_rate = rfclk_sel_map[rfclk_sel];
> + new_parent_rate = clk_hw_round_rate(clk->ref, new_parent_rate);
> + if (rfclk_sel != lynx_rfclk_to_sel(new_parent_rate))
> + continue;
> +
> + *parent_rate = new_parent_rate;
> + return mult_frac(new_parent_rate, ratio, HZ_PER_KHZ);
> + }
> +
> + return -EINVAL;
> +}
> +
> +static int lynx_pll_set_rate(struct clk_hw *hw, unsigned long rate_khz,
> + unsigned long parent_rate)
> +{
> + int frate_sel, rfclk_sel;
> + struct lynx_clk *clk = lynx_pll_to_clk(hw);
> + u32 ratio, cr0 = lynx_read(clk, PLLaCR0(clk->idx));
> +
> + dev_dbg(clk->dev, "set rate pll%d new=%llu parent=%lu\n", clk->idx,
> + (u64)rate_khz * HZ_PER_KHZ, parent_rate);
> +
> + frate_sel = lynx_frate_to_sel(rate_khz);
> + if (frate_sel < 0)
> + return frate_sel;
> +
> + rfclk_sel = lynx_rfclk_to_sel(parent_rate);
> + if (rfclk_sel < 0)
> + return rfclk_sel;
> +
> + ratio = lynx_pll_ratio(frate_sel, rfclk_sel);
> + if (!ratio)
> + return -EINVAL;
> +
> + lynx_pll_stop(clk);
> + cr0 &= ~(PLLaCR0_RFCLK_SEL | PLLaCR0_FRATE_SEL);
> + cr0 |= FIELD_PREP(PLLaCR0_RFCLK_SEL, rfclk_sel);
> + cr0 |= FIELD_PREP(PLLaCR0_FRATE_SEL, frate_sel);
> + lynx_write(clk, cr0, PLLaCR0(clk->idx));
> + /* Don't bother resetting if it's off */
> + if (cr0 & PLLaCR0_POFF)
> + return 0;
> + return lynx_pll_reset(clk);
> +}
> +
> +static const struct clk_ops lynx_pll_clk_ops = {
> + .prepare = lynx_pll_prepare,
> + .disable = lynx_pll_disable,
> + .is_enabled = lynx_pll_is_enabled,
> + .recalc_rate = lynx_pll_recalc_rate,
> + .round_rate = lynx_pll_round_rate,
> + .set_rate = lynx_pll_set_rate,
> +};
> +
> +static void lynx_ex_dly_disable(struct clk_hw *hw)
> +{
> + struct lynx_clk *clk = lynx_ex_dly_to_clk(hw);
> + u32 cr0 = lynx_read(clk, PLLaCR0(clk->idx));
> +
> + cr0 &= ~PLLaCR0_DLYDIV_SEL;
> + lynx_write(clk, PLLaCR0(clk->idx), cr0);
> +}
> +
> +static int lynx_ex_dly_enable(struct clk_hw *hw)
> +{
> + struct lynx_clk *clk = lynx_ex_dly_to_clk(hw);
> + u32 cr0 = lynx_read(clk, PLLaCR0(clk->idx));
> +
> + cr0 &= ~PLLaCR0_DLYDIV_SEL;
> + cr0 |= FIELD_PREP(PLLaCR0_DLYDIV_SEL, PLLaCR0_DLYDIV_SEL_16);
> + lynx_write(clk, PLLaCR0(clk->idx), cr0);
> + return 0;
> +}
> +
> +static int lynx_ex_dly_is_enabled(struct clk_hw *hw)
> +{
> + struct lynx_clk *clk = lynx_ex_dly_to_clk(hw);
> +
> + return lynx_read(clk, PLLaCR0(clk->idx)) & PLLaCR0_DLYDIV_SEL;
> +}
> +
> +static unsigned long lynx_ex_dly_recalc_rate(struct clk_hw *hw,
> + unsigned long parent_rate)
> +{
> + return parent_rate / 16;
> +}
> +
> +static const struct clk_ops lynx_ex_dly_clk_ops = {
> + .enable = lynx_ex_dly_enable,
> + .disable = lynx_ex_dly_disable,
> + .is_enabled = lynx_ex_dly_is_enabled,
> + .recalc_rate = lynx_ex_dly_recalc_rate,
> +};
> +
> +static int lynx_clk_init(struct clk_hw_onecell_data *hw_data,
> + struct device *dev, struct regmap *regmap,
> + unsigned int index)
> +{
> + const struct clk_hw *pll_parents, *ex_dly_parents;
> + struct clk_init_data pll_init = {
> + .ops = &lynx_pll_clk_ops,
> + .parent_hws = &pll_parents,
> + .num_parents = 1,
> + .flags = CLK_GET_RATE_NOCACHE | CLK_SET_RATE_PARENT |
> + CLK_OPS_PARENT_ENABLE,
> + };
> + struct clk_init_data ex_dly_init = {
> + .ops = &lynx_ex_dly_clk_ops,
> + .parent_hws = &ex_dly_parents,
> + .num_parents = 1,
> + };
> + struct clk *ref;
> + struct lynx_clk *clk;
> + char *ref_name;
> + int ret;
> +
> + clk = devm_kzalloc(dev, sizeof(*clk), GFP_KERNEL);
> + if (!clk)
> + return -ENOMEM;
> +
> + clk->dev = dev;
> + clk->regmap = regmap;
> + clk->idx = index;
> +
> + ref_name = kasprintf(GFP_KERNEL, "ref%d", index);
> + pll_init.name = kasprintf(GFP_KERNEL, "%s.pll%d_khz", dev_name(dev),
> + index);
> + ex_dly_init.name = kasprintf(GFP_KERNEL, "%s.pll%d_ex_dly_khz",
> + dev_name(dev), index);
> + if (!ref_name || !pll_init.name || !ex_dly_init.name) {
> + ret = -ENOMEM;
> + goto out;
> + }
> +
> + ref = devm_clk_get(dev, ref_name);
> + if (IS_ERR(clk->ref)) {
> + ret = PTR_ERR(clk->ref);
> + dev_err_probe(dev, ret, "could not get %s\n", ref_name);
> + goto out;
> + }
> +
> + clk->ref = __clk_get_hw(ref);
Please don't use __clk_get_hw() for this. Instead use struct
clk_parent_data and set a DT index in the index member to map to this
clk.
> + pll_parents = clk->ref;
> + clk->pll.init = &pll_init;
> + ret = devm_clk_hw_register(dev, &clk->pll);
> + if (ret) {
> + dev_err_probe(dev, ret, "could not register %s\n",
> + pll_init.name);
> + goto out;
> + }
> +
> + ex_dly_parents = &clk->pll;
> + clk->ex_dly.init = &ex_dly_init;
> + ret = devm_clk_hw_register(dev, &clk->ex_dly);
> + if (ret)
> + dev_err_probe(dev, ret, "could not register %s\n",
> + ex_dly_init.name);
> +
> + hw_data->hws[LYNX10G_PLLa(index)] = &clk->pll;
> + hw_data->hws[LYNX10G_PLLa_EX_DLY(index)] = &clk->ex_dly;
> +
> +out:
> + kfree(ref_name);
> + kfree(pll_init.name);
> + kfree(ex_dly_init.name);
> + return ret;
> +}
> +
> +#define NUM_PLLS 2
> +#define NUM_CLKS (NUM_PLLS * LYNX10G_CLKS_PER_PLL)
> +
> +int lynx_clks_init(struct device *dev, struct regmap *regmap,
> + struct clk *plls[2], struct clk *ex_dlys[2])
> +{
> + int ret, i;
> + struct clk_hw_onecell_data *hw_data;
> +
> + hw_data = devm_kzalloc(dev, struct_size(hw_data, hws, NUM_CLKS),
> + GFP_KERNEL);
> + if (!hw_data)
> + return -ENOMEM;
> + hw_data->num = NUM_CLKS;
> +
> + for (i = 0; i < NUM_PLLS; i++) {
> + ret = lynx_clk_init(hw_data, dev, regmap, i);
> + if (ret)
> + return ret;
> +
> + plls[i] = hw_data->hws[LYNX10G_PLLa(i)]->clk;
> + ex_dlys[i] = hw_data->hws[LYNX10G_PLLa_EX_DLY(i)]->clk;
Use clk_hw_get_clk() please.
> + }
> +
> + ret = devm_of_clk_add_hw_provider(dev, of_clk_hw_onecell_get, hw_data);
> + if (ret)
> + dev_err_probe(dev, ret, "could not register clock provider\n");
> +
> + return ret;
> +}
