On 24/10/2022 12:26, Martin Zaťovič wrote: > This patch documents the devicetree entry for a Wiegand bus. Do not use "This commit/patch". https://elixir.bootlin.com/linux/v5.17.1/source/Documentation/process/submitting-patches.rst#L95 > A Wiegand bus follows the Wiegand protocol. The bus claims two GPIO > lines over which the communication is realized. It also introduces > parameters to control the pulse durations and the length of a gap > after finishing sending a frame. > > Signed-off-by: Martin Zaťovič <m.zatovic1@xxxxxxxxx> > --- > .../devicetree/bindings/bus/wiegand.yaml | 75 +++++++++++++++++++ > 1 file changed, 75 insertions(+) > create mode 100644 Documentation/devicetree/bindings/bus/wiegand.yaml > > diff --git a/Documentation/devicetree/bindings/bus/wiegand.yaml b/Documentation/devicetree/bindings/bus/wiegand.yaml > new file mode 100644 > index 000000000000..cc8d3c46bcde > --- /dev/null > +++ b/Documentation/devicetree/bindings/bus/wiegand.yaml > @@ -0,0 +1,75 @@ > +# SPDX-License-Identifier: GPL-2.0 Dual license > +%YAML 1.2 > +--- > +$id: http://devicetree.org/schemas/bus/wiegand.yaml# > +$schema: http://devicetree.org/meta-schemas/core.yaml# > + > +title: Wiegand Bus > + > +maintainers: > + - Martin Zaťovič <m.zatovic1@xxxxxxxxx> > + > +description: | > + Wiegand interface is a wiring standard popularized in the 1980s. To this day > + many card readers, fingerprint readers, sensors, etc. use Wiegand interface > + particularly for access control applications. It utilizes two wires to > + transmit the data - D0 and D1. > + > + Both data lines are initially pulled up. To send a bit of value 1, the D1 > + line is set low. Similarly to send a bit of value 0, the D0 line is set low. > + > +properties: > + $nodename: > + pattern: "^wiegand(@.*|-[0-9a-f])*$" > + > + compatible: > + contains: > + const: wiegand I think you are still making some shortcuts in design and this also causes some misunderstanding. If this is a bus, then there should be child device(s). But there is none. If there is no device, how are you going to use this? Imagine now a SPI controller without child device... If this is a bus, then one controller implementing it might be using GPIOs, but other one might have dedicated lines. Unless it's not possible and all Wiegand implementations use GPIOs? It does not sound right. > + > + data-hi-gpios: > + description: GPIO spec for data-hi line to use. This line is initially > + pulled up to high value. Wiegand write of a bit of value 1 results in > + this line being pulled down for pulse length duration. > + maxItems: 1 > + > + data-lo-gpios: > + description: GPIO spec for data-lo line to use. This line is initially > + pulled up to high value. Wiegand write of a bit of value 0 results in > + this line being pulled down for pulse length duration. > + maxItems: 1 > + > + pulse-len: > + description: length of the low pulse for both data-lo and data-hi lines. > + maxItems: 1 > + > + interval-len: > + description: length of a whole bit (both the pulse and the high phase) for > + both data-hi and data-lo lines in usecs; defaults to 2000us. > + maxItems: 1 > + > + frame-gap: > + description: length of the last bit of a frame (both the pulse and the high > + phase) in usec; defaults to 2000us. For these properties you must use standard units. https://github.com/devicetree-org/dt-schema/blob/main/dtschema/schemas/property-units.yaml Best regards, Krzysztof