The TLMM pin controller follows generic pin-controller bindings, so should have subnodes with '-state' and '-pins'. Otherwise the subnodes (level one and two) are not properly matched. This method also unifies the bindings with other Qualcomm TLMM and LPASS pinctrl bindings. The change causes indentation decrement, so the diff-hunk looks big, but there are no functional changes in the subnode "properties" section. The only difference there is removal of blank lines between common GPIO pinconf properties. Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@xxxxxxxxxx> Acked-by: Rob Herring <robh@xxxxxxxxxx> Reviewed-by: Bjorn Andersson <andersson@xxxxxxxxxx> --- .../bindings/pinctrl/qcom,sm8250-pinctrl.yaml | 117 ++++++++++-------- 1 file changed, 62 insertions(+), 55 deletions(-) diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,sm8250-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/qcom,sm8250-pinctrl.yaml index 9447b79655e2..aa8315a4d9b1 100644 --- a/Documentation/devicetree/bindings/pinctrl/qcom,sm8250-pinctrl.yaml +++ b/Documentation/devicetree/bindings/pinctrl/qcom,sm8250-pinctrl.yaml @@ -58,62 +58,69 @@ properties: wakeup-parent: true -#PIN CONFIGURATION NODES patternProperties: - '^.*$': - if: - type: object - then: - $ref: qcom,tlmm-common.yaml#/$defs/qcom-tlmm-state - properties: - pins: - description: - List of gpio pins affected by the properties specified in this - subnode. - items: - oneOf: - - pattern: "^gpio([0-9]|[1-9][0-9]|1[0-7][0-9])$" - - enum: [ sdc2_clk, sdc2_cmd, sdc2_data, ufs_reset ] - minItems: 1 - maxItems: 36 - - function: - description: - Specify the alternative function to be configured for the specified - pins. - - enum: [ aoss_cti, atest, audio_ref, cam_mclk, cci_async, cci_i2c, - cci_timer0, cci_timer1, cci_timer2, cci_timer3, cci_timer4, cri_trng, - cri_trng0, cri_trng1, dbg_out, ddr_bist, ddr_pxi0, ddr_pxi1, - ddr_pxi2, ddr_pxi3, dp_hot, dp_lcd, gcc_gp1, gcc_gp2, gcc_gp3, gpio, - ibi_i3c, jitter_bist, lpass_slimbus, mdp_vsync, mdp_vsync0, - mdp_vsync1, mdp_vsync2, mdp_vsync3, mi2s0_data0, mi2s0_data1, - mi2s0_sck, mi2s0_ws, mi2s1_data0, mi2s1_data1, mi2s1_sck, mi2s1_ws, - mi2s2_data0, mi2s2_data1, mi2s2_sck, mi2s2_ws, pci_e0, pci_e1, - pci_e2, phase_flag, pll_bist, pll_bypassnl, pll_clk, pll_reset, - pri_mi2s, prng_rosc, qdss_cti, qdss_gpio, qspi0, qspi1, qspi2, qspi3, - qspi_clk, qspi_cs, qup0, qup1, qup10, qup11, qup12, qup13, qup14, - qup15, qup16, qup17, qup18, qup19, qup2, qup3, qup4, qup5, qup6, - qup7, qup8, qup9, qup_l4, qup_l5, qup_l6, sd_write, sdc40, sdc41, - sdc42, sdc43, sdc4_clk, sdc4_cmd, sec_mi2s, sp_cmu, tgu_ch0, tgu_ch1, - tgu_ch2, tgu_ch3, tsense_pwm1, tsense_pwm2, tsif0_clk, tsif0_data, - tsif0_en, tsif0_error, tsif0_sync, tsif1_clk, tsif1_data, tsif1_en, - tsif1_error, tsif1_sync, usb2phy_ac, usb_phy, vsense_trigger ] - - bias-pull-down: true - - bias-pull-up: true - - bias-disable: true - drive-strength: true - output-high: true - - output-low: true - - required: - - pins - - additionalProperties: false + "-state$": + oneOf: + - $ref: "#/$defs/qcom-sm8250-tlmm-state" + - patternProperties: + "-pins$": + $ref: "#/$defs/qcom-sm8250-tlmm-state" + additionalProperties: false + +$defs: + qcom-sm8250-tlmm-state: + type: object + description: + Pinctrl node's client devices use subnodes for desired pin configuration. + Client device subnodes use below standard properties. + $ref: qcom,tlmm-common.yaml#/$defs/qcom-tlmm-state + + properties: + pins: + description: + List of gpio pins affected by the properties specified in this + subnode. + items: + oneOf: + - pattern: "^gpio([0-9]|[1-9][0-9]|1[0-7][0-9])$" + - enum: [ sdc2_clk, sdc2_cmd, sdc2_data, ufs_reset ] + minItems: 1 + maxItems: 36 + + function: + description: + Specify the alternative function to be configured for the specified + pins. + + enum: [ aoss_cti, atest, audio_ref, cam_mclk, cci_async, cci_i2c, + cci_timer0, cci_timer1, cci_timer2, cci_timer3, cci_timer4, cri_trng, + cri_trng0, cri_trng1, dbg_out, ddr_bist, ddr_pxi0, ddr_pxi1, + ddr_pxi2, ddr_pxi3, dp_hot, dp_lcd, gcc_gp1, gcc_gp2, gcc_gp3, gpio, + ibi_i3c, jitter_bist, lpass_slimbus, mdp_vsync, mdp_vsync0, + mdp_vsync1, mdp_vsync2, mdp_vsync3, mi2s0_data0, mi2s0_data1, + mi2s0_sck, mi2s0_ws, mi2s1_data0, mi2s1_data1, mi2s1_sck, mi2s1_ws, + mi2s2_data0, mi2s2_data1, mi2s2_sck, mi2s2_ws, pci_e0, pci_e1, + pci_e2, phase_flag, pll_bist, pll_bypassnl, pll_clk, pll_reset, + pri_mi2s, prng_rosc, qdss_cti, qdss_gpio, qspi0, qspi1, qspi2, qspi3, + qspi_clk, qspi_cs, qup0, qup1, qup10, qup11, qup12, qup13, qup14, + qup15, qup16, qup17, qup18, qup19, qup2, qup3, qup4, qup5, qup6, + qup7, qup8, qup9, qup_l4, qup_l5, qup_l6, sd_write, sdc40, sdc41, + sdc42, sdc43, sdc4_clk, sdc4_cmd, sec_mi2s, sp_cmu, tgu_ch0, tgu_ch1, + tgu_ch2, tgu_ch3, tsense_pwm1, tsense_pwm2, tsif0_clk, tsif0_data, + tsif0_en, tsif0_error, tsif0_sync, tsif1_clk, tsif1_data, tsif1_en, + tsif1_error, tsif1_sync, usb2phy_ac, usb_phy, vsense_trigger ] + + bias-pull-down: true + bias-pull-up: true + bias-disable: true + drive-strength: true + output-high: true + output-low: true + + required: + - pins + + additionalProperties: false allOf: - $ref: "pinctrl.yaml#" -- 2.34.1
