Hi,
This patchset addresses problems with reg ranges and
additional $refs. It also limits phy-mode and aligns examples.
Best regards,
Michał
---
Changelog:
v4->v5
- drop '+' from all patternProperties
- restrict range of patternProperties to [0-2] in top level
- drop the $ref in patternProperties:'^...':properties:reg
- add patternProperties:'^...':properties:reg:maximum:2
- drop $ref in patternProperties:'^...':properties:phys
- add patternProperties:'^...':properties:phys:maxItems:1
- limit phy-mode to the subset found in dts files
- reflect the order of subnodes' properties in subnodes' required:
- restrict range of pattern to [0-2] in marvell,armada-7k-pp22 case
- restrict range of pattern to [0-1] in marvell,armada-375-pp2 case
- align to 4 spaces all examples:
- add specified maximum to allOf:if:then-else:properties:reg
v3->v4
- change commit message of first patch
- move allOf:$ref to patternProperties:'^...':$ref
- deprecate port-id in favour of reg
- move reg to front of properties list in patternProperties
- reflect the order of properties in required list in
patternProperties
- add unevaluatedProperties: false to patternProperties
- change unevaluated- to additionalProperties at top level
- add property phys: to ports subnode
- extend example binding with additional information about phys and sfp
- hook phys property to phy-consumer.yaml schema
v2->v3
- move 'reg:description' to 'allOf:if:then'
- change '#size-cells: true' and '#address-cells: true'
to '#size-cells: const: 0' and '#address-cells: const: 1'
- replace all occurences of pattern "^eth\{hex_num}*"
with "^(ethernet-)?port@[0-9]+$"
- add description in 'patternProperties:^...'
- add 'patternProperties:^...:interrupt-names:minItems: 1'
- add 'patternProperties:^...:reg:description'
- update 'patternProperties:^...:port-id:description'
- add 'patternProperties:^...:required: - reg'
- update '*:description:' to uppercase
- add 'allOf:then:required:marvell,system-controller'
- skip quotation marks from 'allOf:$ref'
- add 'else' schema to match 'allOf:if:then'
- restrict 'clocks' in 'allOf:if:then'
- restrict 'clock-names' in 'allOf:if:then'
- add #address-cells=<1>; #size-cells=<0>; in 'examples:'
- change every "ethX" to "ethernet-port@X" in 'examples:'
- add "reg" and comment in all ports in 'examples:'
- change /ethernet/eth0/phy-mode in examples://Armada-375
to "rgmii-id"
- replace each cpm_ with cp0_ in 'examples:'
- replace each _syscon0 with _clk0 in 'examples:'
- remove each eth0X label in 'examples:'
- update armada-375.dtsi and armada-cp11x.dtsi to match
marvell,pp2.yaml
v1->v2
- move 'properties' to the front of the file
- remove blank line after 'properties'
- move 'compatible' to the front of 'properties'
- move 'clocks', 'clock-names' and 'reg' definitions to 'properties'
- substitute all occurences of 'marvell,armada-7k-pp2' with
'marvell,armada-7k-pp22'
- add properties:#size-cells and properties:#address-cells
- specify list in 'interrupt-names'
- remove blank lines after 'patternProperties'
- remove '^interrupt' and '^#.*-cells$' patterns
- remove blank line after 'allOf'
- remove first 'if-then-else' block from 'allOf'
- negate the condition in allOf:if schema
- delete 'interrupt-controller' from section 'examples'
- delete '#interrupt-cells' from section 'examples'
Marcin Wojtas (2):
arm64: dts: marvell: Update network description to match schema
ARM: dts: armada-375: Update network description to match schema
Michał Grzelak (1):
dt-bindings: net: marvell,pp2: convert to json-schema
.../devicetree/bindings/net/marvell,pp2.yaml | 305 ++++++++++++++++++
.../devicetree/bindings/net/marvell-pp2.txt | 141 --------
MAINTAINERS | 2 +-
arch/arm/boot/dts/armada-375.dtsi | 12 +-
arch/arm64/boot/dts/marvell/armada-cp11x.dtsi | 17 +-
5 files changed, 325 insertions(+), 152 deletions(-)
create mode 100644 Documentation/devicetree/bindings/net/marvell,pp2.yaml
delete mode 100644 Documentation/devicetree/bindings/net/marvell-pp2.txt
--
2.37.3
