Add MMC1 and 2 nodes. MMC1 is SDcard and MMC2 is eMMC. NOTE on MMC1 card detect: Ideally, we should be using in-built SDCD support, but we dont have it yet. So, use the fact that control module of DRA7 is setup such that no matter what mode one configures it, GPIO option is always hardwired in - use GPIO mode for SDcard detection. [peter.ujfalusi@xxxxxx] The power line feeding the SD card is also used by other devices on the EVM. Use generic name instead of mmc2_3v3 so when other devices want to use the same regulator it will look a bit better. Signed-off-by: Nishanth Menon <nm@xxxxxx> Signed-off-by: Peter Ujfalusi <peter.ujfalusi@xxxxxx> --- Apologies on the spam, I got my own name screwed up -fixing that right now Changes in V2: Fixes the formatting error in author name. V1: https://patchwork.kernel.org/patch/5125291/ arch/arm/boot/dts/dra72-evm.dts | 59 +++++++++++++++++++++++++++++++++++++++ 1 file changed, 59 insertions(+) diff --git a/arch/arm/boot/dts/dra72-evm.dts b/arch/arm/boot/dts/dra72-evm.dts index 1242a17..945a826 100644 --- a/arch/arm/boot/dts/dra72-evm.dts +++ b/arch/arm/boot/dts/dra72-evm.dts @@ -17,6 +17,13 @@ device_type = "memory"; reg = <0x80000000 0x40000000>; /* 1024 MB */ }; + + evm_3v3: fixedregulator-evm_3v3 { + compatible = "regulator-fixed"; + regulator-name = "evm_3v3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; }; &dra7_pmx_core { @@ -32,6 +39,33 @@ 0x424 (PIN_INPUT_PULLUP | MUX_MODE1) /* wakeup3.sys_nirq1 */ >; }; + + mmc1_pins_default: mmc1_pins_default { + pinctrl-single,pins = < + 0x36c (PIN_INPUT | MUX_MODE14) /* mmc1sdcd.gpio219 */ + 0x354 (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_clk.clk */ + 0x358 (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_cmd.cmd */ + 0x35c (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat0.dat0 */ + 0x360 (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat1.dat1 */ + 0x364 (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat2.dat2 */ + 0x368 (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat3.dat3 */ + >; + }; + + mmc2_pins_default: mmc2_pins_default { + pinctrl-single,pins = < + 0x9c (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a23.mmc2_clk */ + 0xb0 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_cs1.mmc2_cmd */ + 0xa0 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a24.mmc2_dat0 */ + 0xa4 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a25.mmc2_dat1 */ + 0xa8 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a26.mmc2_dat2 */ + 0xac (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a27.mmc2_dat3 */ + 0x8c (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a19.mmc2_dat4 */ + 0x90 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a20.mmc2_dat5 */ + 0x94 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a21.mmc2_dat6 */ + 0x98 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a22.mmc2_dat7 */ + >; + }; }; &i2c1 { @@ -159,3 +193,28 @@ &uart1 { status = "okay"; }; + +&mmc1 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&mmc1_pins_default>; + + vmmc-supply = <&ldo1_reg>; + bus-width = <4>; + /* + * SDCD signal is not being used here - using the fact that GPIO mode + * is a viable alternative + */ + cd-gpios = <&gpio6 27 0>; +}; + +&mmc2 { + /* SW5-3 in ON position */ + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&mmc2_pins_default>; + + vmmc-supply = <&evm_3v3>; + bus-width = <8>; + ti,non-removable; +}; -- 1.7.9.5 -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
