Allwinner F1C100s has the most simple USB PHY among all Allwinner SoCs, because it has only one OTG USB controller, no host-only OHCI/EHCI controllers. Add a binding document for it. Following the current situation of one YAML file per SoC, this one is based on allwinner,sun8i-v3s-usb-phy.yaml, but with OHCI/EHCI-related bits removed. (The same driver in Linux, phy-sun4i-usb, covers all these binding files now.) Signed-off-by: Icenowy Zheng <uwu@xxxxxxxxxx> Reviewed-by: Rob Herring <robh@xxxxxxxxxx> --- Changes in v2: - Clarify the relation with other phy-sun4i-usb bindings. - Added Rob's ACK. .../phy/allwinner,suniv-f1c100s-usb-phy.yaml | 83 +++++++++++++++++++ 1 file changed, 83 insertions(+) create mode 100644 Documentation/devicetree/bindings/phy/allwinner,suniv-f1c100s-usb-phy.yaml diff --git a/Documentation/devicetree/bindings/phy/allwinner,suniv-f1c100s-usb-phy.yaml b/Documentation/devicetree/bindings/phy/allwinner,suniv-f1c100s-usb-phy.yaml new file mode 100644 index 000000000000..22ff8e0f2331 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/allwinner,suniv-f1c100s-usb-phy.yaml @@ -0,0 +1,83 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/phy/allwinner,suniv-f1c100s-usb-phy.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Allwinner F1C100s USB PHY Device Tree Bindings + +maintainers: + - Chen-Yu Tsai <wens@xxxxxxxx> + - Maxime Ripard <mripard@xxxxxxxxxx> + +properties: + "#phy-cells": + const: 1 + + compatible: + const: allwinner,suniv-f1c100s-usb-phy + + reg: + maxItems: 1 + description: PHY Control registers + + reg-names: + const: phy_ctrl + + clocks: + maxItems: 1 + description: USB OTG PHY bus clock + + clock-names: + const: usb0_phy + + resets: + maxItems: 1 + description: USB OTG reset + + reset-names: + const: usb0_reset + + usb0_id_det-gpios: + maxItems: 1 + description: GPIO to the USB OTG ID pin + + usb0_vbus_det-gpios: + maxItems: 1 + description: GPIO to the USB OTG VBUS detect pin + + usb0_vbus_power-supply: + description: Power supply to detect the USB OTG VBUS + + usb0_vbus-supply: + description: Regulator controlling USB OTG VBUS + +required: + - "#phy-cells" + - compatible + - clocks + - clock-names + - reg + - reg-names + - resets + - reset-names + +additionalProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + #include <dt-bindings/clock/suniv-ccu-f1c100s.h> + #include <dt-bindings/reset/suniv-ccu-f1c100s.h> + + phy@1c13400 { + compatible = "allwinner,suniv-f1c100s-usb-phy"; + reg = <0x01c13400 0x10>; + reg-names = "phy_ctrl"; + clocks = <&ccu CLK_USB_PHY0>; + clock-names = "usb0_phy"; + resets = <&ccu RST_USB_PHY0>; + reset-names = "usb0_reset"; + #phy-cells = <1>; + usb0_id_det-gpios = <&pio 4 2 GPIO_ACTIVE_HIGH>; + }; -- 2.37.1
