The TLMM pin controller follows generic pin-controller bindings, so should have subnodes with '-state' and '-pins'. Otherwise the subnodes (level one and two) are not properly matched. This method also unifies the bindings with other Qualcomm TLMM and LPASS pinctrl bindings. The change causes indentation decrement, so the diff-hunk looks big, but there are no functional changes in the subnode "properties" section. The only difference there is removal of blank lines between common GPIO pinconf properties. Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@xxxxxxxxxx> --- .../bindings/pinctrl/qcom,sm8250-pinctrl.yaml | 145 +++++++++--------- 1 file changed, 75 insertions(+), 70 deletions(-) diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,sm8250-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/qcom,sm8250-pinctrl.yaml index d7d8e5d3b659..da708c748a36 100644 --- a/Documentation/devicetree/bindings/pinctrl/qcom,sm8250-pinctrl.yaml +++ b/Documentation/devicetree/bindings/pinctrl/qcom,sm8250-pinctrl.yaml @@ -58,77 +58,82 @@ properties: wakeup-parent: true -#PIN CONFIGURATION NODES patternProperties: - '^.*$': - if: - type: object - then: - properties: - pins: - description: - List of gpio pins affected by the properties specified in this - subnode. - items: - oneOf: - - pattern: "^gpio([0-9]|[1-9][0-9]|1[0-7][0-9])$" - - enum: [ sdc2_clk, sdc2_cmd, sdc2_data, ufs_reset ] - minItems: 1 - maxItems: 36 - - function: - description: - Specify the alternative function to be configured for the specified - pins. - - enum: [ aoss_cti, atest, audio_ref, cam_mclk, cci_async, cci_i2c, - cci_timer0, cci_timer1, cci_timer2, cci_timer3, cci_timer4, cri_trng, - cri_trng0, cri_trng1, dbg_out, ddr_bist, ddr_pxi0, ddr_pxi1, - ddr_pxi2, ddr_pxi3, dp_hot, dp_lcd, gcc_gp1, gcc_gp2, gcc_gp3, gpio, - ibi_i3c, jitter_bist, lpass_slimbus, mdp_vsync, mdp_vsync0, - mdp_vsync1, mdp_vsync2, mdp_vsync3, mi2s0_data0, mi2s0_data1, - mi2s0_sck, mi2s0_ws, mi2s1_data0, mi2s1_data1, mi2s1_sck, mi2s1_ws, - mi2s2_data0, mi2s2_data1, mi2s2_sck, mi2s2_ws, pci_e0, pci_e1, - pci_e2, phase_flag, pll_bist, pll_bypassnl, pll_clk, pll_reset, - pri_mi2s, prng_rosc, qdss_cti, qdss_gpio, qspi0, qspi1, qspi2, qspi3, - qspi_clk, qspi_cs, qup0, qup1, qup10, qup11, qup12, qup13, qup14, - qup15, qup16, qup17, qup18, qup19, qup2, qup3, qup4, qup5, qup6, - qup7, qup8, qup9, qup_l4, qup_l5, qup_l6, sd_write, sdc40, sdc41, - sdc42, sdc43, sdc4_clk, sdc4_cmd, sec_mi2s, sp_cmu, tgu_ch0, tgu_ch1, - tgu_ch2, tgu_ch3, tsense_pwm1, tsense_pwm2, tsif0_clk, tsif0_data, - tsif0_en, tsif0_error, tsif0_sync, tsif1_clk, tsif1_data, tsif1_en, - tsif1_error, tsif1_sync, usb2phy_ac, usb_phy, vsense_trigger ] - - drive-strength: - enum: [2, 4, 6, 8, 10, 12, 14, 16] - default: 2 - description: - Selects the drive strength for the specified pins, in mA. - - bias-pull-down: true - - bias-pull-up: true - - bias-disable: true - - output-high: true - - output-low: true - - required: - - pins - - allOf: - - $ref: "qcom,tlmm-common.yaml#/$defs/qcom-tlmm-state" - - if: - properties: - pins: - pattern: "^gpio([0-9]|[1-9][0-9]|1[0-7][0-9])$" - then: - required: - - function - - additionalProperties: false + "-state$": + oneOf: + - $ref: "#/$defs/qcom-sm8250-tlmm-state" + - patternProperties: + "-pins$": + $ref: "#/$defs/qcom-sm8250-tlmm-state" + additionalProperties: false + +$defs: + qcom-sm8250-tlmm-state: + type: object + description: + Pinctrl node's client devices use subnodes for desired pin configuration. + Client device subnodes use below standard properties. + properties: + pins: + description: + List of gpio pins affected by the properties specified in this + subnode. + items: + oneOf: + - pattern: "^gpio([0-9]|[1-9][0-9]|1[0-7][0-9])$" + - enum: [ sdc2_clk, sdc2_cmd, sdc2_data, ufs_reset ] + minItems: 1 + maxItems: 36 + + function: + description: + Specify the alternative function to be configured for the specified + pins. + + enum: [ aoss_cti, atest, audio_ref, cam_mclk, cci_async, cci_i2c, + cci_timer0, cci_timer1, cci_timer2, cci_timer3, cci_timer4, cri_trng, + cri_trng0, cri_trng1, dbg_out, ddr_bist, ddr_pxi0, ddr_pxi1, + ddr_pxi2, ddr_pxi3, dp_hot, dp_lcd, gcc_gp1, gcc_gp2, gcc_gp3, gpio, + ibi_i3c, jitter_bist, lpass_slimbus, mdp_vsync, mdp_vsync0, + mdp_vsync1, mdp_vsync2, mdp_vsync3, mi2s0_data0, mi2s0_data1, + mi2s0_sck, mi2s0_ws, mi2s1_data0, mi2s1_data1, mi2s1_sck, mi2s1_ws, + mi2s2_data0, mi2s2_data1, mi2s2_sck, mi2s2_ws, pci_e0, pci_e1, + pci_e2, phase_flag, pll_bist, pll_bypassnl, pll_clk, pll_reset, + pri_mi2s, prng_rosc, qdss_cti, qdss_gpio, qspi0, qspi1, qspi2, qspi3, + qspi_clk, qspi_cs, qup0, qup1, qup10, qup11, qup12, qup13, qup14, + qup15, qup16, qup17, qup18, qup19, qup2, qup3, qup4, qup5, qup6, + qup7, qup8, qup9, qup_l4, qup_l5, qup_l6, sd_write, sdc40, sdc41, + sdc42, sdc43, sdc4_clk, sdc4_cmd, sec_mi2s, sp_cmu, tgu_ch0, tgu_ch1, + tgu_ch2, tgu_ch3, tsense_pwm1, tsense_pwm2, tsif0_clk, tsif0_data, + tsif0_en, tsif0_error, tsif0_sync, tsif1_clk, tsif1_data, tsif1_en, + tsif1_error, tsif1_sync, usb2phy_ac, usb_phy, vsense_trigger ] + + drive-strength: + enum: [2, 4, 6, 8, 10, 12, 14, 16] + default: 2 + description: + Selects the drive strength for the specified pins, in mA. + + bias-pull-down: true + bias-pull-up: true + bias-disable: true + output-high: true + output-low: true + + required: + - pins + + allOf: + - $ref: "qcom,tlmm-common.yaml#/$defs/qcom-tlmm-state" + - if: + properties: + pins: + pattern: "^gpio([0-9]|[1-9][0-9]|1[0-7][0-9])$" + then: + required: + - function + + additionalProperties: false allOf: - $ref: "pinctrl.yaml#" -- 2.34.1
