[PATCH v2 net-next 12/14] dt-bindings: net: dsa: ocelot: add ocelot-ext documentation

[Colin Foster <colin.foster@xxxxxxxxxxxxxxxx>]

The ocelot-ext driver is another sub-device of the Ocelot / Felix driver
system, which currently supports the four internal copper phys.

Signed-off-by: Colin Foster <colin.foster@xxxxxxxxxxxxxxxx>
---

v2
    * New patch

---
 .../bindings/net/dsa/mscc,ocelot.yaml         | 58 +++++++++++++++++++
 1 file changed, 58 insertions(+)

diff --git a/Documentation/devicetree/bindings/net/dsa/mscc,ocelot.yaml b/Documentation/devicetree/bindings/net/dsa/mscc,ocelot.yaml
index 8d93ed9c172c..bed575236261 100644
--- a/Documentation/devicetree/bindings/net/dsa/mscc,ocelot.yaml
+++ b/Documentation/devicetree/bindings/net/dsa/mscc,ocelot.yaml
@@ -54,9 +54,21 @@ description: |
       - phy-mode = "1000base-x": on ports 0, 1, 2, 3
       - phy-mode = "2500base-x": on ports 0, 1, 2, 3
 
+  VSC7412 (Ocelot-Ext):
+
+    The Ocelot family consists of four devices, the VSC7511, VSC7512, VSC7513,
+    and the VSC7514. The VSC7513 and VSC7514 both have an internal MIPS
+    processor that natively support Linux. Additionally, all four devices
+    support control over external interfaces, SPI and PCIe. The Ocelot-Ext
+    driver is for the external control portion.
+
+    The following PHY interface type are currently supported:
+      - phy-mode = "internal": on ports 0, 1, 2, 3
+
 properties:
   compatible:
     enum:
+      - mscc,vsc7512-switch
       - mscc,vsc9953-switch
       - pci1957,eef0
 
@@ -258,3 +270,49 @@ examples:
             };
         };
     };
+  # Ocelot-ext VSC7512
+  - |
+    spi {
+        soc@0 {
+            compatible = "mscc,vsc7512";
+            #address-cells = <1>;
+            #size-cells = <1>;
+
+            ethernet-switch@0 {
+                compatible = "mscc,vsc7512-switch";
+                reg = <0 0>;
+
+                ethernet-ports {
+                    #address-cells = <1>;
+                    #size-cells = <0>;
+
+                    port@0 {
+                        reg = <0>;
+                        label = "cpu";
+                        ethernet = <&mac_sw>;
+                        phy-handle = <&phy0>;
+                        phy-mode = "internal";
+                    };
+
+                    port@1 {
+                        reg = <1>;
+                        label = "swp1";
+                        phy-mode = "internal";
+                        phy-handle = <&phy1>;
+                    };
+
+                    port@2 {
+                        reg = <2>;
+                        phy-mode = "internal";
+                        phy-handle = <&phy2>;
+                    };
+
+                    port@3 {
+                        reg = <3>;
+                        phy-mode = "internal";
+                        phy-handle = <&phy3>;
+                    };
+                };
+            };
+        };
+    };
-- 
2.25.1