On Wed, 2022-06-01 at 12:37 +0200, Krzysztof Kozlowski wrote: > On 31/05/2022 15:50, Fabien Parent wrote: > > Add device-tree for the MT8365 SoC. More information can be found > > about that SoC at the following address: > > https://www.mediatek.com/products/aiot/i350-mt8365 > > > > Signed-off-by: Fabien Parent <fparent@xxxxxxxxxxxx> > > --- > > arch/arm64/boot/dts/mediatek/mt8365.dtsi | 1047 > > ++++++++++++++++++++++ > > 1 file changed, 1047 insertions(+) > > create mode 100644 arch/arm64/boot/dts/mediatek/mt8365.dtsi > > > > diff --git a/arch/arm64/boot/dts/mediatek/mt8365.dtsi > > b/arch/arm64/boot/dts/mediatek/mt8365.dtsi > > new file mode 100644 > > index 000000000000..e22b1d259418 > > --- /dev/null > > +++ b/arch/arm64/boot/dts/mediatek/mt8365.dtsi > > @@ -0,0 +1,1047 @@ > > +// SPDX-License-Identifier: (GPL-2.0 OR MIT) > > +/* > > + * Copyright (c) 2018 MediaTek Inc. > > + */ > > + > > +#include <dt-bindings/clock/mediatek,mt8365-clk.h> > > +#include <dt-bindings/interrupt-controller/arm-gic.h> > > +#include <dt-bindings/interrupt-controller/irq.h> > > +#include <dt-bindings/phy/phy.h> > > +#include <dt-bindings/power/mt8365-power.h> > > +#include <dt-bindings/memory/mt8365-larb-port.h> > > +#include <dt-bindings/thermal/thermal.h> > > + > > +/ { > > + compatible = "mediatek,mt8365"; > > + interrupt-parent = <&sysirq>; > > + #address-cells = <2>; > > + #size-cells = <2>; > > + > > + aliases { > > + ovl0 = &ovl0; > > + rdma0 = &rdma0; > > + rdma1 = &rdma1; > > + color0 = &color0; > > + ccorr0 = &ccorr0; > > + aal0 = &aal0; > > + gamma0 = &gamma0; > > + dither0 = &dither0; > > + dsi0 = &dsi0; > > + dpi0 = &dpi0; > > + }; > > + > > + cpus: cpus { > > + #address-cells = <1>; > > + #size-cells = <0>; > > + > > + cpu-map { > > + cluster0: cluster0 { > > + core0 { > > + cpu = <&cpu0>; > > + }; > > + core1 { > > + cpu = <&cpu1>; > > + }; > > + core2 { > > + cpu = <&cpu2>; > > + }; > > + core3 { > > + cpu = <&cpu3>; > > + }; > > + }; > > + }; > > + > > + cpu0: cpu@0 { > > + device_type = "cpu"; > > + compatible = "arm,cortex-a53"; > > + reg = <0x0>; > > + clock-frequency = <1600000000>; > > + clocks = <&mcucfg CLK_MCU_BUS_SEL>, > > + <&apmixedsys CLK_APMIXED_MAINPLL>; > > + clock-names = "cpu", "intermediate"; > > + operating-points-v2 = <&cluster0_opp>; > > + #cooling-cells = <2>; > > + enable-method = "psci"; > > + }; > > + > > + cpu1: cpu@1 { > > + device_type = "cpu"; > > + compatible = "arm,cortex-a53"; > > + reg = <0x1>; > > + clock-frequency = <1600000000>; > > + clocks = <&mcucfg CLK_MCU_BUS_SEL>, > > + <&apmixedsys CLK_APMIXED_MAINPLL>; > > + clock-names = "cpu", "intermediate", "armpll"; > > + operating-points-v2 = <&cluster0_opp>; > > + #cooling-cells = <2>; > > + enable-method = "psci"; > > + }; > > + > > + cpu2: cpu@2 { > > + device_type = "cpu"; > > + compatible = "arm,cortex-a53"; > > + reg = <0x2>; > > + clock-frequency = <1600000000>; > > + clocks = <&mcucfg CLK_MCU_BUS_SEL>, > > + <&apmixedsys CLK_APMIXED_MAINPLL>; > > + clock-names = "cpu", "intermediate", "armpll"; > > + operating-points-v2 = <&cluster0_opp>; > > + #cooling-cells = <2>; > > + enable-method = "psci"; > > + }; > > + > > + cpu3: cpu@3 { > > + device_type = "cpu"; > > + compatible = "arm,cortex-a53"; > > + reg = <0x3>; > > + clock-frequency = <1600000000>; > > + clocks = <&mcucfg CLK_MCU_BUS_SEL>, > > + <&apmixedsys CLK_APMIXED_MAINPLL>; > > + clock-names = "cpu", "intermediate", "armpll"; > > + operating-points-v2 = <&cluster0_opp>; > > + #cooling-cells = <2>; > > + enable-method = "psci"; > > + }; > > + }; > > + > > + cluster0_opp: opp-table-0 { > > + compatible = "operating-points-v2"; > > + opp-shared; > > + opp-850000000 { > > + opp-hz = /bits/ 64 <850000000>; > > + opp-microvolt = <650000>; > > + }; > > + opp-918000000 { > > + opp-hz = /bits/ 64 <918000000>; > > + opp-microvolt = <668750>; > > + }; > > + opp-987000000 { > > + opp-hz = /bits/ 64 <987000000>; > > + opp-microvolt = <687500>; > > + }; > > + opp-1056000000 { > > + opp-hz = /bits/ 64 <1056000000>; > > + opp-microvolt = <706250>; > > + }; > > + opp-1125000000 { > > + opp-hz = /bits/ 64 <1125000000>; > > + opp-microvolt = <725000>; > > + }; > > + opp-1216000000 { > > + opp-hz = /bits/ 64 <1216000000>; > > + opp-microvolt = <750000>; > > + }; > > + opp-1308000000 { > > + opp-hz = /bits/ 64 <1308000000>; > > + opp-microvolt = <775000>; > > + }; > > + opp-1400000000 { > > + opp-hz = /bits/ 64 <1400000000>; > > + opp-microvolt = <800000>; > > + }; > > + opp-1466000000 { > > + opp-hz = /bits/ 64 <1466000000>; > > + opp-microvolt = <825000>; > > + }; > > + opp-1533000000 { > > + opp-hz = /bits/ 64 <1533000000>; > > + opp-microvolt = <850000>; > > + }; > > + opp-1633000000 { > > + opp-hz = /bits/ 64 <1633000000>; > > + opp-microvolt = <887500>; > > + }; > > + opp-1700000000 { > > + opp-hz = /bits/ 64 <1700000000>; > > + opp-microvolt = <912500>; > > + }; > > + opp-1767000000 { > > + opp-hz = /bits/ 64 <1767000000>; > > + opp-microvolt = <937500>; > > + }; > > + opp-1834000000 { > > + opp-hz = /bits/ 64 <1834000000>; > > + opp-microvolt = <962500>; > > + }; > > + opp-1917000000 { > > + opp-hz = /bits/ 64 <1917000000>; > > + opp-microvolt = <993750>; > > + }; > > + opp-2001000000 { > > + opp-hz = /bits/ 64 <2001000000>; > > + opp-microvolt = <1025000>; > > + }; > > + }; > > + > > + clk26m: oscillator { > > + compatible = "fixed-clock"; > > + #clock-cells = <0>; > > + clock-frequency = <26000000>; > > This does not look like property of a SoC. Are you sure MT8365 SoC > has > this clock (not the board)? > > > + clock-output-names = "clk26m"; > > + }; > > + > > + psci { > > + compatible = "arm,psci-1.0"; > > + method = "smc"; > > + }; > > + > > + reserved-memory { > > + #address-cells = <2>; > > + #size-cells = <2>; > > + ranges; > > + > > + /* 128 KiB reserved for ARM Trusted Firmware (BL31) */ > > + bl31_secmon_reserved: secmon@43000000 { > > + no-map; > > + reg = <0 0x43000000 0 0x20000>; > > + }; > > + }; > > + > > + soc { > > + #address-cells = <2>; > > + #size-cells = <2>; > > + compatible = "simple-bus"; > > + ranges; > > + > > + gic: interrupt-controller@c000000 { > > + compatible = "arm,gic-v3"; > > + #interrupt-cells = <4>; > > Why do you have four cells here (and passing 0 as interrupt)? > > > + interrupt-parent = <&gic>; > > + interrupt-controller; > > + reg = <0 0x0c000000 0 0x80000>, > > + <0 0x0c080000 0 0x80000>; > > + > > + interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH 0>; > > + }; > > + > > + topckgen: syscon@10000000 { > > + compatible = "mediatek,mt8365-topckgen", > > "syscon"; > > + reg = <0 0x10000000 0 0x1000>; > > + #clock-cells = <1>; > > + }; > > + > > + infracfg: syscon@10001000 { > > + compatible = "mediatek,mt8365-infracfg", > > "syscon"; > > + reg = <0 0x10001000 0 0x1000>; > > + #clock-cells = <1>; > > + }; > > + > > + pericfg: syscon@10003000 { > > + compatible = "mediatek,mt8365-pericfg", > > "syscon"; > > + reg = <0 0x10003000 0 0x1000>; > > + #clock-cells = <1>; > > + }; > > + > > + syscfg_pctl: syscfg-pctl@10005000 { > > This is I guess also syscon, like other nodes? > > > + compatible = "syscon"; > > You need specific compatible. Please run `make dtbs_check` and fix > the > errors. > > > + reg = <0 0x10005000 0 0x1000>; > > + }; > > + > > + scpsys: syscon@10006000 { > > + compatible = "syscon", "simple-mfd"; > > You need specific compatible. > > > + reg = <0 0x10006000 0 0x1000>; > > + #power-domain-cells = <1>; > > This is definitely wrong now. It's not a simple-mfd device, so please > do > not use that property. > > > + > > + /* System Power Manager */ > > + spm: power-controller { > > + compatible = "mediatek,mt8365-power- > > controller"; > > + #address-cells = <1>; > > + #size-cells = <0>; > > + #power-domain-cells = <1>; > > + > > + /* power domains of the SoC */ > > The comment suggests you will later add here power domains not for > the > SoC. If that's not true, just skip the comment. > > > + power-domain@MT8365_POWER_DOMAIN_MM { > > + reg = <MT8365_POWER_DOMAIN_MM>; > > + clocks = <&topckgen > > CLK_TOP_MM_SEL>, > > + <&mmsys > > CLK_MM_MM_SMI_COMMON>, > > + <&mmsys > > CLK_MM_MM_SMI_COMM0>, > > + <&mmsys > > CLK_MM_MM_SMI_COMM1>, > > + <&mmsys > > CLK_MM_MM_SMI_LARB0>; > > + clock-names = "mm", "mm-0", > > "mm-1", > > + "mm-2", "mm-3"; > > + #power-domain-cells = <0>; > > + mediatek,infracfg = > > <&infracfg>; > > + mediatek,infracfg_nao = > > <&infracfg_nao>; > > + #address-cells = <1>; > > + #size-cells = <0>; > > + > > + power-domain@MT8365_POWER_DOMAI > > N_CAM { > > + reg = > > <MT8365_POWER_DOMAIN_CAM>; > > + clocks = <&camsys > > CLK_CAM_LARB2>, > > + <&camsys > > CLK_CAM_SENIF>, > > + <&camsys > > CLK_CAMSV0>, > > + <&camsys > > CLK_CAMSV1>, > > + <&camsys > > CLK_CAM_FDVT>, > > + <&camsys > > CLK_CAM_WPE>; > > + clock-names = "cam-0", > > "cam-1", > > + "cam-2", > > "cam-3", > > + "cam-4", > > "cam-5"; > > + #power-domain-cells = > > <0>; > > + mediatek,infracfg = > > <&infracfg>; > > + mediatek,smi = > > <&smi_common>; > > + }; > > + > > + power-domain@MT8365_POWER_DOMAI > > N_VDEC { > > + reg = > > <MT8365_POWER_DOMAIN_VDEC>; > > + #power-domain-cells = > > <0>; > > + mediatek,smi = > > <&smi_common>; > > + }; > > + > > + power-domain@MT8365_POWER_DOMAI > > N_VENC { > > + reg = > > <MT8365_POWER_DOMAIN_VENC>; > > + #power-domain-cells = > > <0>; > > + mediatek,smi = > > <&smi_common>; > > + }; > > + > > + power-domain@MT8365_POWER_DOMAI > > N_APU { > > + reg = > > <MT8365_POWER_DOMAIN_APU>; > > + clocks = <&infracfg > > CLK_IFR_APU_AXI>, > > + <&apu > > CLK_APU_IPU_CK>, > > + <&apu > > CLK_APU_AXI>, > > + <&apu > > CLK_APU_JTAG>, > > + <&apu > > CLK_APU_IF_CK>, > > + <&apu > > CLK_APU_EDMA>, > > + <&apu > > CLK_APU_AHB>; > > + clock-names = "apu", > > "apu-0", > > + "apu-1", > > "apu-2", > > + "apu-3", > > "apu-4", > > + "apu-5"; > > + #power-domain-cells = > > <0>; > > + mediatek,infracfg = > > <&infracfg>; > > + mediatek,smi = > > <&smi_common>; > > + }; > > + }; > > + > > + power-domain@MT8365_POWER_DOMAIN_CONN { > > + reg = > > <MT8365_POWER_DOMAIN_CONN>; > > + clocks = <&topckgen > > CLK_TOP_CONN_32K>, > > + <&topckgen > > CLK_TOP_CONN_26M>; > > + clock-names = "conn", "conn1"; > > + #power-domain-cells = <0>; > > + mediatek,infracfg = > > <&infracfg>; > > + }; > > + > > + power-domain@MT8365_POWER_DOMAIN_MFG { > > + reg = > > <MT8365_POWER_DOMAIN_MFG>; > > + clocks = <&topckgen > > CLK_TOP_MFG_SEL>; > > + clock-names = "mfg"; > > + #power-domain-cells = <0>; > > + mediatek,infracfg = > > <&infracfg>; > > + }; > > + > > + power-domain@MT8365_POWER_DOMAIN_AUDIO > > { > > + reg = > > <MT8365_POWER_DOMAIN_AUDIO>; > > + clocks = <&topckgen > > CLK_TOP_AUD_INTBUS_SEL>, > > + <&infracfg > > CLK_IFR_AUDIO>, > > + <&infracfg > > CLK_IFR_AUD_26M_BK>; > > + clock-names = "audio", > > "audio1", "audio2"; > > + #power-domain-cells = <0>; > > + mediatek,infracfg = > > <&infracfg>; > > + }; > > + > > + power-domain@MT8365_POWER_DOMAIN_DSP { > > + reg = > > <MT8365_POWER_DOMAIN_DSP>; > > + clocks = <&topckgen > > CLK_TOP_DSP_SEL>, > > + <&topckgen > > CLK_TOP_DSP_26M>; > > + clock-names = "dsp", "dsp1"; > > + #power-domain-cells = <0>; > > + mediatek,infracfg = > > <&infracfg>; > > + }; > > + }; > > + }; > > + > > + watchdog: watchdog@10007000 { > > + compatible = "mediatek,mt8365-wdt", > > + "mediatek,mt6589-wdt"; > > + reg = <0 0x10007000 0 0x100>; > > + #reset-cells = <1>; > > + }; > > + > > + gpt: apxgpt@10008000 { > > Generic node names, so "timer" > > > + compatible = "mediatek,mt8365-timer", > > + "mediatek,mt6577-timer"; > > + reg = <0 0x10008000 0 0x1000>; > > + interrupts = <GIC_SPI 114 IRQ_TYPE_LEVEL_LOW>; > > + clocks = <&topckgen CLK_TOP_SYS_26M_D2>; > > + clock-names = "clk13m"; > > + }; > > + > > + pio: pinctrl@1000b000 { > > + compatible = "mediatek,mt8365-pinctrl"; > > + reg = <0 0x1000b000 0 0x1000>; > > + mediatek,pctl-regmap = <&syscfg_pctl>; > > + pins-are-numbered; > > + gpio-controller; > > + #gpio-cells = <2>; > > + interrupt-controller; > > + #interrupt-cells = <2>; > > + interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>; > > + }; > > + > > + apmixedsys: syscon@1000c000 { > > + compatible = "mediatek,mt8365-apmixedsys", > > "syscon"; > > + reg = <0 0x1000c000 0 0x1000>; > > + #clock-cells = <1>; > > + }; > > + > > + pwrap: pwrap@1000d000 { > > + compatible = "mediatek,mt8365-pwrap"; > > + reg = <0 0x1000d000 0 0x1000>; > > + reg-names = "pwrap"; > > + interrupts = <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>; > > + clocks = <&infracfg CLK_IFR_PWRAP_SPI>, > > + <&infracfg CLK_IFR_PMIC_AP>, > > + <&infracfg CLK_IFR_PWRAP_SYS>, > > + <&infracfg CLK_IFR_PWRAP_TMR>; > > + clock-names = "spi", "wrap", "sys", "tmr"; > > + }; > > + > > + keypad: kp@10010000 { > > s/kp/keypad/ > > > + compatible = "mediatek,mt6779-keypad"; > > + reg = <0 0x10010000 0 0x1000>; > > + wakeup-source; > > + interrupts = <GIC_SPI 124 > > IRQ_TYPE_EDGE_FALLING>; > > + clocks = <&clk26m>; > > + clock-names = "kpd"; > > + status = "disabled"; > > + }; > > + > > + mcucfg: syscon@10200000 { > > + compatible = "mediatek,mt8365-mcucfg", > > "syscon"; > > + reg = <0 0x10200000 0 0x2000>; > > + #clock-cells = <1>; > > + }; > > + > > + sysirq: intpol-controller@10200a80 { > > interrupt-controller > > > + compatible = "mediatek,mt8365-sysirq", > > + "mediatek,mt6577-sysirq"; > > + interrupt-controller; > > + #interrupt-cells = <3>; > > + interrupt-parent = <&gic>; > > + reg = <0 0x10200a80 0 0x20>; > > + }; > > + > > + iommu: iommu@10205000 { > > + compatible = "mediatek,mt8365-m4u"; > > + reg = <0 0x10205000 0 0x1000>; > > + interrupts = <GIC_SPI 102 IRQ_TYPE_LEVEL_LOW>; > > + mediatek,larbs = <&larb0>, <&larb1>, <&larb2>, > > <&larb3>; > > + #iommu-cells = <1>; > > + }; > > + > > + infracfg_nao: infracfg-nao@1020e000 { > > Other nodes are named syscon > > > + compatible = "syscon"; > > No, syscon cannot be alone. > > > + reg = <0 0x1020e000 0 0x1000>; > > + }; > > + > > + rng: rng@1020f000 { > > + compatible = "mediatek,mt8365-rng", > > + "mediatek,mt7623-rng"; > > + reg = <0 0x1020f000 0 0x100>; > > + clocks = <&infracfg CLK_IFR_TRNG>; > > + clock-names = "rng"; > > + }; > > + > > + apdma: dma-controller@11000280 { > > + compatible = "mediatek,mt8365-uart-dma", > > + "mediatek,mt6577-uart-dma"; > > + reg = <0 0x11000280 0 0x80>, > > + <0 0x11000300 0 0x80>, > > + <0 0x11000380 0 0x80>, > > + <0 0x11000400 0 0x80>, > > + <0 0x11000580 0 0x80>, > > + <0 0x11000600 0 0x80>; > > + interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_LOW>, > > + <GIC_SPI 46 IRQ_TYPE_LEVEL_LOW>, > > + <GIC_SPI 47 IRQ_TYPE_LEVEL_LOW>, > > + <GIC_SPI 48 IRQ_TYPE_LEVEL_LOW>, > > + <GIC_SPI 51 IRQ_TYPE_LEVEL_LOW>, > > + <GIC_SPI 52 IRQ_TYPE_LEVEL_LOW>; > > + dma-requests = <6>; > > + clocks = <&infracfg CLK_IFR_AP_DMA>; > > + clock-names = "apdma"; > > + #dma-cells = <1>; > > + }; > > + > > + auxadc: adc@11001000 { > > + compatible = "mediatek,mt8365-auxadc", > > + "mediatek,mt8173-auxadc"; > > + reg = <0 0x11001000 0 0x1000>; > > + clocks = <&infracfg CLK_IFR_AUXADC>; > > + clock-names = "main"; > > + #io-channel-cells = <1>; > > + }; > > + > > + uart0: serial@11002000 { > > + compatible = "mediatek,mt8365-uart", > > + "mediatek,mt6577-uart"; > > + reg = <0 0x11002000 0 0x1000>; > > + interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_LOW>; > > + clocks = <&clk26m>, <&infracfg CLK_IFR_UART0>; > > + clock-names = "baud", "bus"; > > + dmas = <&apdma 0 > > + &apdma 1>; > > You need to split these into two phandles. > > > + dma-names = "tx", "rx"; > > + status = "disabled"; > > + }; > > + > > + uart1: serial@11003000 { > > + compatible = "mediatek,mt8365-uart", > > + "mediatek,mt6577-uart"; > > + reg = <0 0x11003000 0 0x1000>; > > + interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_LOW>; > > + clocks = <&clk26m>, <&infracfg CLK_IFR_UART1>; > > + clock-names = "baud", "bus"; > > + dmas = <&apdma 2 > > + &apdma 3>; > > Ditto. > > > + dma-names = "tx", "rx"; > > + status = "disabled"; > > + }; > > + > > + uart2: serial@11004000 { > > + compatible = "mediatek,mt8365-uart", > > + "mediatek,mt6577-uart"; > > + reg = <0 0x11004000 0 0x1000>; > > + interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_LOW>; > > + clocks = <&clk26m>, <&infracfg CLK_IFR_UART2>; > > + clock-names = "baud", "bus"; > > + dmas = <&apdma 4 > > + &apdma 5>; > > + dma-names = "tx", "rx"; > > + status = "disabled"; > > + }; > > + > > + pwm: pwm@11006000 { > > + compatible = "mediatek,mt8365-pwm"; > > + reg = <0 0x11006000 0 0x1000>; > > + #pwm-cells = <2>; > > + interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_LOW>; > > + clocks = <&infracfg CLK_IFR_PWM_HCLK>, > > + <&infracfg CLK_IFR_PWM>, > > + <&infracfg CLK_IFR_PWM1>, > > + <&infracfg CLK_IFR_PWM2>, > > + <&infracfg CLK_IFR_PWM3>; > > + clock-names = "top", "main", "pwm1", "pwm2", > > "pwm3"; > > + }; > > + > > + i2c0: i2c@11007000 { > > + compatible = "mediatek,mt8365-i2c", > > + "mediatek,mt8168-i2c"; > > + reg = <0 0x11007000 0 0xa0>, > > + <0 0x11000080 0 0x80>; > > + interrupts = <GIC_SPI 28 IRQ_TYPE_LEVEL_LOW>; > > + clock-div = <1>; > > + clocks = <&infracfg CLK_IFR_I2C0_AXI>, > > + <&infracfg CLK_IFR_AP_DMA>; > > + clock-names = "main", "dma"; > > + #address-cells = <1>; > > + #size-cells = <0>; > > + status = "disabled"; > > + }; > > + > > + i2c1: i2c@11008000 { > > + compatible = "mediatek,mt8365-i2c", > > + "mediatek,mt8168-i2c"; > > + reg = <0 0x11008000 0 0xa0>, > > + <0 0x11000100 0 0x80>; > > + interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_LOW>; > > + clock-div = <1>; > > + clocks = <&infracfg CLK_IFR_I2C1_AXI>, > > + <&infracfg CLK_IFR_AP_DMA>; > > + clock-names = "main", "dma"; > > + #address-cells = <1>; > > + #size-cells = <0>; > > + status = "disabled"; > > + }; > > + > > + i2c2: i2c@11009000 { > > + compatible = "mediatek,mt8365-i2c", > > + "mediatek,mt8168-i2c"; > > + reg = <0 0x11009000 0 0xa0>, > > + <0 0x11000180 0 0x80>; > > + interrupts = <GIC_SPI 30 IRQ_TYPE_LEVEL_LOW>; > > + clock-div = <1>; > > + clocks = <&infracfg CLK_IFR_I2C2_AXI>, > > + <&infracfg CLK_IFR_AP_DMA>; > > + clock-names = "main", "dma"; > > + #address-cells = <1>; > > + #size-cells = <0>; > > + status = "disabled"; > > + }; > > + > > + spi: spi@1100a000 { > > + compatible = "mediatek,mt8365-spi", > > + "mediatek,mt7622-spi"; > > + #address-cells = <1>; > > + #size-cells = <0>; > > + reg = <0 0x1100a000 0 0x100>; > > Reg goes after compatible. > > > + interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_LOW>; > > + clocks = <&topckgen CLK_TOP_UNIVPLL2_D4>, > > + <&topckgen CLK_TOP_SPI_SEL>, > > + <&infracfg CLK_IFR_SPI0>; > > + clock-names = "parent-clk", "sel-clk", "spi- > > clk"; > > + status = "disabled"; > > + }; > > + > > + thermal: thermal@1100b000 { > > + compatible = "mediatek,mt8365-thermal"; > > + reg = <0 0x1100b000 0 0x1000>; > > + interrupts = <GIC_SPI 22 IRQ_TYPE_LEVEL_LOW>; > > + clocks = <&infracfg CLK_IFR_THERM>, > > + <&infracfg CLK_IFR_AUXADC>; > > + clock-names = "therm", "auxadc"; > > + mediatek,auxadc = <&auxadc>; > > + mediatek,apmixedsys = <&apmixedsys>; > > + nvmem-cells = <&thermal_calibration>; > > + nvmem-cell-names = "calibration-data"; > > + #thermal-sensor-cells = <1>; > > + }; > > + > > + disp_pwm: disp-pwm@1100e000 { > > Generic node names, so "pwm" > > > + compatible = "mediatek,mt8365-disp-pwm", > > + "mediatek,mt8183-disp-pwm"; > > + reg = <0 0x1100e000 0 0x1000>; > > + #pwm-cells = <2>; > > + clocks = <&topckgen CLK_TOP_DISP_PWM_SEL>, > > + <&infracfg CLK_IFR_DISP_PWM>; > > + clock-names = "main", "mm"; > > + power-domains = <&spm MT8365_POWER_DOMAIN_MM>; > > + status = "disabled"; > > + }; > > + > > + i2c3: i2c@1100f000 { > > + compatible = "mediatek,mt8365-i2c", > > + "mediatek,mt8168-i2c"; > > + reg = <0 0x1100f000 0 0xa0>, > > + <0 0x11000200 0 0x80>; > > + interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_LOW>; > > + clock-div = <1>; > > + clocks = <&infracfg CLK_IFR_I2C3_AXI>, > > + <&infracfg CLK_IFR_AP_DMA>; > > + clock-names = "main", "dma"; > > + #address-cells = <1>; > > + #size-cells = <0>; > > + status = "disabled"; > > + }; > > + > > + ssusb: usb@11201000 { > > + compatible = "mediatek,mt8365-mtu3", > > "mediatek,mtu3"; > > + reg = <0 0x11201000 0 0x2e00>, > > + <0 0x11203e00 0 0x0100>; > > + reg-names = "mac", "ippc"; > > + interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_LOW>; > > + phys = <&u2port0 PHY_TYPE_USB2>, > > + <&u2port1 PHY_TYPE_USB2>; > > + clocks = <&topckgen CLK_TOP_SSUSB_TOP_CK_EN>, > > + <&infracfg CLK_IFR_SSUSB_REF>, > > + <&infracfg CLK_IFR_SSUSB_SYS>, > > + <&infracfg CLK_IFR_ICUSB>; > > + clock-names = "sys_ck", "ref_ck", "mcu_ck", > > + "dma_ck"; > > + #address-cells = <2>; > > + #size-cells = <2>; > > + ranges; > > + status = "disabled"; > > + > > + usb_host: usb@11200000 { > > + compatible = "mediatek,mt8365-xhci", > > + "mediatek,mtk-xhci"; > > + reg = <0 0x11200000 0 0x1000>; > > + reg-names = "mac"; > > + interrupts = <GIC_SPI 67 > > IRQ_TYPE_LEVEL_LOW>; > > + clocks = <&topckgen > > CLK_TOP_SSUSB_TOP_CK_EN>, > > + <&infracfg CLK_IFR_SSUSB_REF>, > > + <&infracfg CLK_IFR_SSUSB_SYS>, > > + <&infracfg CLK_IFR_ICUSB>, > > + <&infracfg > > CLK_IFR_SSUSB_XHCI>; > > + clock-names = "sys_ck", "ref_ck", > > "mcu_ck", > > + "dma_ck", "xhci_ck"; > > + status = "disabled"; > > + }; > > + }; > > + > > + mmc0: mmc@11230000 { > > + compatible = "mediatek,mt8365-mmc", > > "mediatek,mt8183-mmc"; > > + reg = <0 0x11230000 0 0x1000>, > > + <0 0x11cd0000 0 0x1000>; > > + interrupts = <GIC_SPI 23 IRQ_TYPE_LEVEL_LOW>; > > + clocks = <&topckgen CLK_TOP_MSDC50_0_SEL>, > > + <&infracfg CLK_IFR_MSDC0_HCLK>, > > + <&infracfg CLK_IFR_MSDC0_SRC>; > > + clock-names = "source", "hclk", "source_cg"; > > + status = "disabled"; > > + }; > > + > > + mmc1: mmc@11240000 { > > + compatible = "mediatek,mt8365-mmc", > > "mediatek,mt8183-mmc"; > > + reg = <0 0x11240000 0 0x1000>, > > + <0 0x11c90000 0 0x1000>; > > + interrupts = <GIC_SPI 24 IRQ_TYPE_LEVEL_LOW>; > > + clocks = <&topckgen CLK_TOP_MSDC30_1_SEL>, > > + <&infracfg CLK_IFR_MSDC1_HCLK>, > > + <&infracfg CLK_IFR_MSDC1_SRC>; > > + clock-names = "source", "hclk", "source_cg"; > > + status = "disabled"; > > + }; > > + > > + ethernet: ethernet@112a0000 { > > + compatible = "mediatek,mt8365-eth"; > > + reg = <0 0x112a0000 0 0x1000>; > > + mediatek,pericfg = <&infracfg>; > > + interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>; > > + clocks = <&topckgen CLK_TOP_ETH_SEL>, > > + <&infracfg CLK_IFR_NIC_AXI>, > > + <&infracfg CLK_IFR_NIC_SLV_AXI>; > > + clock-names = "core", "reg", "trans"; > > + status = "disabled"; > > + }; > > + > > + mipi_tx0: dsi-phy@11c00000 { > > + compatible = "mediatek,mt8365-mipi-tx", > > + "mediatek,mt8183-mipi-tx"; > > + reg = <0 0x11c00000 0 0x800>; > > + clocks = <&clk26m>; > > + clock-names = "ref_clk"; > > + #clock-cells = <0>; > > + #phy-cells = <0>; > > + clock-output-names = "mipi_tx0_pll"; > > + }; > > + > > + efuse: efuse@11c50000 { > > + compatible = "mediatek,mt8365-efuse", > > "mediatek,efuse"; > > + reg = <0 0x11c50000 0 0x1000>; > > + #address-cells = <1>; > > + #size-cells = <1>; > > + > > + thermal_calibration: calib@180 { > > + reg = <0x180 0xc>; > > + }; > > + }; > > + > > + u3phy: t-phy@11cc0000 { > > s/t-phy/phy/ can't use phy here, if will cause dt-binding check fail. > > > + compatible = "mediatek,mt8365-tphy", > > + "mediatek,generic-tphy-v2"; > > + #address-cells = <2>; > > + #phy-cells = <1>; > > address-cells, then size, then phy > > > + #size-cells = <2>; > > + ranges; > > + status = "okay"; > > No need for status ok. > > > + > > + u2port0: usb-phy@11cc0000 { > > + reg = <0 0x11cc0000 0 0x400>; > > + clocks = <&topckgen > > CLK_TOP_SSUSB_PHY_CK_EN>, > > + <&topckgen > > CLK_TOP_USB20_48M_EN>; > > + clock-names = "ref", "da_ref"; > > + #phy-cells = <1>; > > + status = "okay"; > > Ditto > > > + }; > > + > > + u2port1: usb-phy@11cc1000 { > > + reg = <0 0x11cc1000 0 0x400>; > > + clocks = <&topckgen > > CLK_TOP_SSUSB_PHY_CK_EN>, > > + <&topckgen > > CLK_TOP_USB20_48M_EN>; > > + clock-names = "ref", "da_ref"; > > + #phy-cells = <1>; > > + status = "okay"; > > + }; > > + }; > > + > > + mfgcfg: syscon@13000000 { > > + compatible = "mediatek,mt8365-mfgcfg", > > "syscon"; > > + reg = <0 0x13000000 0 0x1000>; > > + #clock-cells = <1>; > > + }; > > + > > + mmsys: syscon@14000000 { > > + compatible = "mediatek,mt8365-mmsys", "syscon"; > > + reg = <0 0x14000000 0 0x1000>; > > + #clock-cells = <1>; > > + }; > > + > > + mutex: mutex@14001000 { > > + compatible = "mediatek,mt8365-disp-mutex"; > > + reg = <0 0x14001000 0 0x1000>; > > + interrupts = <GIC_SPI 154 IRQ_TYPE_LEVEL_LOW>; > > + power-domains = <&spm MT8365_POWER_DOMAIN_MM>; > > + }; > > + > > + smi_common: smi@14002000 { > > s/smi/memory-controller/ in node name? > > > + compatible = "mediatek,mt8365-smi-common", > > + "mediatek,mt8186-smi-common"; > > + reg = <0 0x14002000 0 0x1000>; > > + clocks = <&mmsys CLK_MM_MM_SMI_COMMON>, > > + <&mmsys CLK_MM_MM_SMI_COMMON>, > > + <&mmsys CLK_MM_MM_SMI_COMM0>, > > + <&mmsys CLK_MM_MM_SMI_COMM1>; > > + clock-names = "apb", "smi", "gals0", "gals1"; > > + power-domains = <&spm MT8365_POWER_DOMAIN_MM>; > > + }; > > + > > + larb0: larb@14003000 { > > The same? > > > + compatible = "mediatek,mt8365-smi-larb", > > + "mediatek,mt8186-smi-larb"; > > + reg = <0 0x14003000 0 0x1000>; > > + mediatek,smi = <&smi_common>; > > + clocks = <&mmsys CLK_MM_MM_SMI_LARB0>, > > + <&mmsys CLK_MM_MM_SMI_LARB0>; > > + clock-names = "apb", "smi"; > > + power-domains = <&spm MT8365_POWER_DOMAIN_MM>; > > > > Best regards, > Krzysztof